Gebruiksaanwijzing /service van het product 2004 L-Series van de fabrikant Saturn
Ga naar pagina of 386
Seats and Restraint Systems ........................... 1 - 1 Front Seats ............................................... 1 - 3 Rear Seats ............................................... 1 - 8 Safety Belts .............................................
SATURN and the SATURN Emblem are registered trademarks of Saturn Corporation. GM and the GM Emblem are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Safety Warnings and Symbols You will find a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. { CAUTION: These mean there is something that could hurt you or other people.
Vehicle Damage Warnings Also, in this manual you will find these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage your vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
These are some examples of symbols that may be found on the vehicle: v.
✍ NOTES vi.
Front Seats ..................................................... .1-3 Manual Seats ............................................... .1-3 Driver Seat Height Adjuster ............................. .1-3 Six-Way Power Driver Seat .........................
What Makes an Air Bag Inflate? .................... .1-68 How Does an Air Bag Restrain? .................... .1-68 What Will You See After an Air Bag Inflates? ...... .1-69 Servicing Your Air Bag-Equipped Vehicle ........ .1-71 Adding Equipment to Your Air Bag-Equipped Vehicle .
Front Seats Manual Seats { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Six-Way Power Driver Seat If your vehicle has this feature, the control is located on the outboard side of the driver’s seat. To adjust the seat do any of the following: • Move the seat forward or rearward by pressing the center switch forward or rearward.
Heated Seats If your vehicle has this feature, the thumbwheel controls for both driver and passenger heated seats are located in the center of the instrument panel. Move the thumbwheel to the first circle to warm the seat to a lower temperature and to the second circle for a higher temperature.
On a power driver’s seat, adjust the seatback by pressing the RECLINE switch forward or rearward. But don’t have a seatback reclined if your vehicle is moving.
{ CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job because it will not be against your body.
Rear Seats Split Folding Rear Seat Your vehicle is equipped with a split folding rear seat. A split folding rear seat enables you to carry long cargo by folding down part or all of the rear seat. Sedan On sedans, you can fold either the driver’s or passenger’s right side of the seatback separately or both sides together.
{ CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Wagon On wagons, you can fold either the passenger’s side of the seatback or the entire seatback. To fold down the passenger’s side of the seatback, pull the lever on the corner of the seatback. To lower the entire rear seatback, pull the lever on the corner of the driver’s side seatback.
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. { CAUTION: Do not let anyone ride where he or she can not wear a safety belt properly.
You never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person wouldn’t survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider doesn’t stop. 1-13.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 1-14.
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Q: If I’m a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you’re in an accident – even one that isn’t your fault – you and your passengers can be hurt. Being a good driver doesn’t protect you from things beyond your control, such as bad drivers.
Lap-Shoulder Belt The driver has a lap-shoulder belt. Here is how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats” in the Index. 3. Pick up the latch plate and pull the belt across you.
5. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder belt. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Shoulder Belt Height Adjuster Before you begin to drive, move the shoulder belt adjuster to the height that is right for you. To move it down, press down on the indented part of the height adjuster and move the height adjuster to the desired position.
Q: What’s wrong with this? A: The shoulder belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What’s wrong with this? A: The belt is buckled in the wrong place. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Q: What’s wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What’s wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your retailer to fix it.
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle. Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women.
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Lap-Shoulder Belt All rear seating positions have lap-shoulder belts. Here is how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
To unlatch the belt, just push the button on the buckle. Rear Seat Outside Passenger Positions (Wagon) 1-28.
Lap-Shoulder Belt The positions next to the windows have lap-shoulder belts. Here is how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
To unlatch the belt, just push the button on the buckle. Center Rear Passenger Position (Wagon) 1-31.
Lap Belt When you sit in the center seating position, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt. To make the belt shorter, pull its free end as shown until the belt is snug.
Rear Safety Belt Comfort Guides for Children and Small Adults If you would like to have rear shoulder belt comfort guides installed on your vehicle, contact your retailer. Rear shoulder belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults.
2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough to fasten, your retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Q: What is the proper way to wear safety belts? A: If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured.
{ CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen.
Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Young children should not use the vehicle’s adult safety belts alone, unless there is no other choice. Instead, they need to use a child restraint.
{ CAUTION: Children who are up against, or very close to, any air bag when it inflates can be seriously injured or killed. Air bags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants.
For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous flat surface. Make sure that the infant’s head rests toward the center of the vehicle.
A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system.
Q: How do child restraints work? A: A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Here is why: { CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating air bag.
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
{ CAUTION: Each top tether bracket is designed to anchor only one child restraint. Attaching more than one child restraint to a single bracket could cause the anchor to come loose or even break during a crash. A child or others could be injured if this happens.
Sedan The anchors are located behind the rear seat on the filler panel. In order to get to one of these brackets, you will have to open the trim cover. The trim cover is marked with the symbol for child seat top tether anchor. Wagon Anchor brackets are located on the floor in the cargo area.
{ CAUTION: Routing the top strap for a child restraint over or under the cargo shade could cause the shade to come loose and even break. If this happens, the shade could be thrown about the vehicle in a collision or sudden maneuver. You or others could be injured.
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You’ll find anchors (A) for all three rear seating positions. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts.
In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback at each lower anchor position.
Securing a Child Restraint Designed for the LATCH System 1. Find the LATCH anchorages for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-50 .
3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 4. Pull the rest of shoulder belt all the way out of the retractor to set the lock.
5. To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 6.
3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 4. Pull the rest of shoulder belt all the way out of the retractor to set the lock.
5. To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 6.
1. Make the belt as long as possible by tilting the latch plate and pulling it along the belt. 2. Put the restraint on the seat. 3. Run the vehicle’s safety belt through or around the restraint.
4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. To tighten the belt, pull its free end while you push down on the child restraint.
There is no top strap anchor in the right front passenger’s position. Do not secure a child seat in this position if a national or local law requires that the top strap be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. You may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Air Bag Systems This part explains the frontal and side impact air bag systems. Your vehicle has four air bags: • A frontal air bag for the driver and another frontal air bag for the right front pas.
CAUTION: (Continued) They are not designed to inflate in frontal, in rollover or in rear crashes. Everyone in your vehicle should wear a safety belt properly – whether or not there is an air bag for that person. { CAUTION: Both frontal and side impact air bags inflate with great force, faster than the blink of an eye.
There is a air bag readiness light on the instrument panel, which shows the air bag symbol. The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical problem. See Air Bag Readiness Light on page 3-28 for more information.
The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side. If your vehicle has a side impact air bag for the driver and the person seated directly behind the driver, it is in the ceiling above the side windows.
If your vehicle has a side impact air bag for the right front passenger and the person seated directly behind that passenger, it is in the ceiling above the side windows.
When Should an Air Bag Inflate? The driver’s and right front passenger’s frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system’s designed “threshold level.
What Makes an Air Bag Inflate? In an impact of suff icient severity, the air bag sensing system detects that the vehicle is in a crash. For both frontal and side impact air bags, the sensing system triggers a release of gas from the inflator, which inflates the air bag.
What Will You See After an Air Bag Inflates? After the air bag inflates, it quickly deflates, so quickly that some people may not even realize the air bag inflated.
You must first turn your ignition key to the following ignition switch positions: 1. Turn the ignition key to the OFF position. 2. Turn the ignition key to the RUN position. 3. Turn the ignition key to the OFF position. In many crashes severe enough to inflate an air bag, windshields are broken by vehicle deformation.
Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are air bag system parts in several places around your vehicle.
Adding Equipment to Your Air Bag-Equipped Vehicle Q: If I add a luggage carrier or sunroof to the roof of my vehicle, will it keep the roof-mounted side impact air bags from working properly? A: As lo.
Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash.
✍ NOTES 1-74.
Keys .............................................................. .2-3 Remote Keyless Entry System ........................ .2-4 Remote Keyless Entry System Operation .......... .2-5 Doors and Locks ............................................ .2-9 Door Locks .
Storage Areas ............................................... .2-41 Glove Box .................................................. .2-41 Center Console Storage Area ........................ .2-41 Assist Handles ..........................................
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
One key is used for the ignition and all of the locks. Key code information can be obtained only at the retailer where your vehicle was purchased. These code numbers can be used to make new keys. Additional keys that are needed can be made at any retail service facility provided you have the key code information.
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: • Check the distance. You may be too far from your vehicle.
UNLOCK : Press this button on the remote keyless entry transmitter to unlock the driver’s door. This also disarms the theft-deterrent system. See “Theft-Deterrent System” following for information on disarming the theft-deterrent system. Press the button again within 5 seconds to unlock the rest of the doors.
A chime will sound once the mode has been selected. If you accidentally set off the alarm when entering/exiting the vehicle, you can shut it off by pressing any button on the remote keyless entry transmitter other than the panic alarm button.
2. Once the transmitter is separated, use a pencil or similar object to remove the old battery. Do not use a metal object. 3. Insert the new battery as the instructions under the cover indicate. 4. Snap the transmitter back together tightly to be sure no moisture can enter.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Power Door Locks Press the bottom half of the switch on either front door to lock all of the doors. Push the top half of the switch to unlock all of the doors. The unlocked door indicators on the manual door lock pins will be hidden when the doors are locked.
Programmable Automatic Door Locks With this feature, all the doors will lock as the transaxle is shifted out of PARK (P) if the ignition key is in the RUN position and all doors are closed. The doors will automatically lock if the vehicle is going faster than 3 mph (5 km/h).
When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, the front door power lock switch, or by lifting the rear door manual lock. 2. Open the door from the outside.
Trunk/Liftgate { CAUTION: It can be dangerous to drive with the trunk or liftgate open because carbon monoxide (CO) gas can come into your vehicle. You can not see or smell CO.
Liftgate Release (Wagon) Unlock the liftgate by doing any of the following: • Press the unlock button on your remote keyless entry transmitter twice. • Press the liftgate button on your transmitter. • Press the interior door unlock switch. • Enable the automatic door unlocking feature.
Emergency Trunk Release Handle (Sedan) There is a glow-in-the-dark trunk release handle located inside the trunk near the bottom edge of the trunk lid. This handle will glow following exposure to light. Notice: Using the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk may damage it.
Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Manual Windows On a vehicle with manual windows, use the window crank to open and close each window. Power Windows Switches are located on each side of the shift lever on the console. To open a window press the switch down and lift up to close it. The power windows can operate only when the ignition key is in the RUN or the ACC position.
Window Lock Out The driver’s window controls also include a lock-out switch. Press the window lock switch to the left to stop rear passengers from using their window switches. The driver can still control all the windows with the lock on. Press the right side of the window lock button to return to normal window operation.
During normal operation, the security light will go off approximately five seconds after the key is turned to the RUN ignition position following an engine start. If the engine stalls and the security light flashes, wait until the light stops flashing before trying to restart the engine.
Ignition Positions With the key in the ignition switch, you can turn the switch to four positions. OFF: This position locks your steering column in a vehicle with a manual transmission. It is a theft-deterrent feature. You will only be able to remove your key when the ignition is turned to OFF.
Starting Your Engine Automatic Transaxle Move your shift lever to PARK (P) or NEUTRAL (N). Your engine won’t start in any other position — that is a safety feature. To restart when you’re already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle.
Engine Coolant Heater If your vehicle has this feature, in very cold weather, − 20°F ( − 29°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Automatic Transaxle Operation Your vehicle is equipped with an automatic transaxle, the shift lever is located on the console between the seats. There are several positions for the shift lever. PARK (P): This position locks your front wheels. It’s the best position to use when you start your engine because your vehicle can’t move easily.
Then move the shift lever into the gear you wish. Press the shift lever button before moving the shift lever. See Shifting Out of Park (P) on page 2-30 . REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle.
AUTOMATIC OVERDRIVE ( X ): This position is for normal driving with the automatic transaxle. If you need more power for passing, and you’re: • Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down. • Going about 35 mph (55 km/h), push your accelerator all the way down.
Shift Lock Release If you ever hold the brake pedal down, but still cannot shift out of PARK (P), try this: 1. Turn the ignition to OFF and remove the key. 2. Carefully pry the shift lock override cover from the floor shift console. 3. Lift up and forward to disengage.
Parking Brake The parking brake lever is located between the bucket seats. When parking your vehicle, set the parking brake before shifting your automatic transaxle into PARK (P). To set the parking brake, hold the brake pedal down and pull up on the parking brake lever.
Shifting Into Park (P) (Automatic Transaxle) { CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Leaving Your Vehicle With the Engine Running { CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire.
Shifting Out of Park (P) Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN.
Engine Exhaust { CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different.
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Mirrors Manual Rearview Mirror While you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side.
Automatic Dimming Rearview Mirror with OnStar ® , Compass and Temperature Display Your vehicle may have this feature. When on, an automatic dimming mirror automatically dims to the proper level to minimize glare from lights behind you after dark. The mirror also includes a duel display in the upper right corner of the mirror face.
Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror do the following: 1. Make sure the indicator light, located to the left of the on/off button, is lit.
To adjust for compass variance do the following: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the on/of f button until a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the on/of f button until the desired zone number appears in the display.
Temperature Display The temperature can be displayed by pressing the TEMP button. Pressing the TEMP button once briefly, will toggle the temperature reading from Fahrenheit (°F), Celsius (°C), to off. Automatic Dimming Mirror Operation Press the COMP button to turn the automatic dimming feature on and off.
To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the COMP button for five seconds until a zone number appears in the display. 3. Press the COMP button on the bottom of the mirror until the new zone number appears in the display.
Outside Power Mirrors The outside power mirror control is located on the driver’s door. Use the selector switch located above the round touch pad to choose either the left or right outside mirror. To adjust the mirror press the round touch pad in the desired direction.
OnStar ® System OnStar ® uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information and convenience services.
Luxury and Leisure Plan • All Directions and Connections Plan services • Personal Concierge OnStar ® Personal Calling With OnStar ® Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle.
Load Floor Storage Box Some wagon models have a load floor storage box, which is located in the rear of the vehicle. This storage space is designed to hold small items.
Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-34 . To prevent damage or loss of cargo as you’re driving, check frequently to ensure your cargo is securely fastened.
Removing the Cargo Cover To remove the cargo shade: 1. Unhook the shade and allow it to retract all the way. 2. Grasp the shade on the driver’s side of the vehicle and move it toward the passenger’s side, compressing the spring. 3. Lift up the end of the shade on the driver’s side of the vehicle and remove the cargo shade from the vehicle.
Sunroof If your vehicle has this feature, the switch will be located above your rearview mirror. Your ignition key must be in the RUN or ACC position to operate the sunroof. To open the sunroof three-quarters of the way, press and hold the SLIDE portion of the switch.
✍ NOTES 2-46.
Instrument Panel Overview .............................. .3-2 Hazard Warning Flashers ............................... .3-4 Other Warning Devices .................................. .3-5 Horn ............................................................ .
Instrument Panel Overview 3-2.
The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-24 . B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-6 . C. Cruise Control (If Equipped). See Cruise Control on page 3-10 .
Hazard Warning Flashers Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off. The hazard warning flasher button is located near the center of the instrument panel.
Other Warning Devices If you carry reflective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle. Horn You can sound the horn by pressing the center of your steering wheel. Tilt Wheel Your vehicle may have a tilt wheel which allows you to adjust the steering wheel before you drive.
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals • Headlamps • Headlamp High/Low-Beam Changer • Flash-to-Pass Feature For additional information on the exterior lamps, see Exterior Lamps on page 3-13 .
Headlamp High/Low-Beam Changer To change the headlamps from low beam to high or high beam to low, pull the turn signal lever all the way towards you. Then release it. When the high beams are on, this light on the instrument panel cluster will also be on.
Windshield Wiper Lever The lever on the right side of the steering column operates the windshield wipers. 8 : Pull the lever down and release it for a single wiping cycle. The lever will return to its original position. For more cycles, hold the lever down before releasing it.
Windshield Washer { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. Pull the windshield wiper lever toward you to operate the windshield wipers.
Cruise Control The buttons for the cruise control are located on the steering wheel. I O (Cruise On/Off): Push this button to turn the system on and off. IS (Resume/Accelerate): Push this button to make the vehicle resume a previously set speed or to accelerate when cruise is already active.
Setting Cruise Control { CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press the set/coast button, then release the button and the accelerator pedal. You’ll now cruise at the higher speed.
Ending Cruise Control To end a cruise control session, step lightly on the brake pedal. Stepping on the brake will end the current cruise control session only. Press the cruise on/off button to turn of f the system completely. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased.
Automatic Headlamp System When it is dark enough outside, the headlamps will come on automatically. Your vehicle has a light sensor located on top of the instrument panel. Make sure it is not covered, or the headlamps will be on when you don’t need them.
Interior Lamps Instrument Panel Brightness This feature controls the brightness of the instrument panel lights. The thumbwheel for this feature is located on the instrument panel to the left of the steering column. Turn the thumbwheel up to brighten the lights or down to dim them.
Battery Run-Down Protection Your vehicle is equipped with a battery saver feature designed to protect your vehicle’s battery. When any interior lamp is left on and the ignition is turned off, the battery rundown protection system will automatically turn the lamp off after 20 minutes.
Ashtrays and Cigarette Lighter Your vehicle may have an ashtray and cigarette lighter. To use the lighter, just push it in all the way and let go. When it’s ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot.
Operation To change the current mode, turn the right knob to select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode directs half of the air to the instrument panel outlets, and then directs most of the remaining air to the floor outlets.
AC (Air Conditioning): Press this button to turn the air-conditioning system on or off. When A/C is pressed, an indicator light above the button will come on to let you know that air conditioning is activated. On hot days, open the windows to let hot inside air escape; then close them.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. < REAR: Press this button to turn the rear window defogger on or off. An indicator light above the button will come on to let your know that the rear window defogger is activated.
Automatic Operation To switch the temperature display from degrees Fahrenheit to degrees Celsius, press and hold the AUTO, ECON, and MODE buttons at the same time. AUTO (Automatic): When automatic operation is active the system will control the inside temperature, the air delivery, and the fan speed.
Manual Operation You may manually adjust the air delivery mode or fan speed. OFF: Press this button to turn off the entire climate control system. Outside air will still enter the vehicle. A (Fan): The knob with the fan symbol allows you to manually adjust the fan speed.
Sensor A sensor located on top of the instrument panel is used by the automatic climate control system to adjust the automatic operation of the system. Do not cover this sensor. Defogging and Defrosting You can use either defog or front defrost to clear fog or frost from your windshield.
Outlet Adjustment Use the louvers located on the air outlets to change the direction of the airflow. Operation Tips • Clear away any ice, snow or leaves from the air inlets at the base of the vehicle that may block the flow of air into your vehicle.
5. Release the two locking tabs and pull the filter out. 6. Reverse the steps to install the new air filter. Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them.
Instrument Panel Cluster The instrument cluster is designed to let you know at a glance how the vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles or kilometers. Your vehicle has a tamper-resistant odometer.
Safety Belt Reminder Light When the key is turned to RUN or START, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will flash for several more.
{ CAUTION: If the air bag readiness light stays on after you start your vehicle, it means the air bag system may not be working properly. The air bags in your vehicle may not inflate in a crash, or they could even inflate without a crash.
Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the brake system warning light comes on, there is a brake problem.
Anti-Lock Brake System Warning Light If your vehicle has anti-lock brakes, the anti-lock brake system (ABS) warning light will come on briefly, as a check, when you start your vehicle. If it does not, have your vehicle serviced so that the light works properly when it needs to.
Traction Control System (TCS) Warning Light The Traction Control System (TCS) light will come on when the system is limiting wheel spin. You may feel or hear the system working, but this is normal. The roads may be slippery if this light comes on. Adjust your driving accordingly.
Engine Coolant Temperature Gage This gage measures the temperature of the vehicle’s engine. If the indicator needle moves into the shaded area, the engine is too hot.
Malfunction Indicator Lamp Service Engine Soon Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems.
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: • Light Flashing — A misfire condition has been detected.
Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5 . Poor fuel quality will cause your engine not to run as eff iciently as designed.
Oil Pressure Light If you have a low engine oil pressure problem, this light will stay on after you start your engine, or come on when you are driving. This indicates that your engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem.
Change Engine Oil Light If this light comes on and stays on, it means that service is required for your vehicle. See Scheduled Maintenance on page 6-4 Engine Oil on page 5-16 for more information. Security Light Your vehicle is equipped with a Passlock ® theft-deterrent system.
Daytime Running Lamps Indicator Light This light is located on the instrument panel cluster. It goes on whenever the Daytime Running Lamps are on. See Daytime Running Lamps under Exterior Lamps on page 3-13 for further information. Low Washer Fluid Warning Light This light will come on when your vehicle is low on windshield washer fluid.
Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have left in your tank. When the indicator nears empty, the low fuel light will come on. You still have a little fuel left, but you should get more soon. See Low Fuel Warning Light on page 3-40 for more information.
Audio System(s) Notice: Before adding any sound equipment to your vehicle, like a tape player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer. Also, check federal rules covering mobile radio and telephone units.
AM-FM Radio Playing the Radio ON (Power): Push this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. RCL (Recall): Press this knob to switch the display between the radio station frequency and the time.
Setting Preset Stations Up to 18 stations (six FM1, six FM2, and six AM) can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press AM FM to select FM1, FM2, or AM. 3. Tune in the desired station.
Cancelling Automatic Set The radio retains the previously stored stations so they can be recalled when automatic set is canceled. Press and hold A.SET until you hear a beep. A.SET will no longer appear on the display. Setting the Tone (Bass/Treble) BASS: Press this knob lightly so it extends.
Radio with CD Playing the Radio PUSH ON (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease volume. RCL (Recall): Press this knob to switch the display between the radio station frequency and the time.
Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six FM1, six FM2, and six AM) by performing the following steps: 1. Turn the radio on. 2. Press AM FM to select FM1, FM2, or AM.
Setting the Tone (Bass/Treble) MODE: Press this button until BAS or TRE appears on the display. Press the plus or minus buttons to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, you may want to decrease the treble.
Do not add paper labels to CDs, they could get caught in the CD player. Do not play 3 inch CDs without a standard adapter CD. If an error appears on the display, see “CD Messages” later in this section. 1 PRV (Previous): Press this pushbutton to go to the start of the current track if more than eight seconds have played.
RCL (Recall): Press this button to see the track number. Press this button again to see how long the current track has been playing. AM FM: Press this button to listen to the radio when a CD is playing. The inactive CD will remain safely inside the radio for future listening.
Radio with Cassette and CD Playing the Radio PUSH ON (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease volume. RCL (Recall): Press this knob to switch the display between the radio station frequency and the time.
Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six FM1, six FM2, and six AM) by performing the following steps: 1. Turn the radio on. 2. Press AM FM to select FM1, FM2, or AM.
Setting the Tone (Bass/Treble) BASS/TREB (Treble): Press and release this knob until BASS or TREB appears on the display. Turn the knob to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, you may want to decrease the treble.
1 PREV (Previous): Press this pushbutton to go to the beginning of the current selection. Press this pushbutton again to go to the previous selection on the tape. 2 NEXT: Press this pushbutton to go to the next selection on the tape. The radio will play while the tape advances.
Cassette Tape Messages ERR (Error): If this message appears on the display, the tape will not play because of one of the following errors. • The tape is tight and the player cannot turn the tape hubs. Remove the tape. Hold the tape with the open end down and try to turn the right hub counterclockwise with a pencil.
If playing a CD-R the sound quality may be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. You may experience an increase in skipping, diff iculty in finding tracks and/or diff iculty in loading and ejecting.
CD TP (Tape): Press this button to play a CD when listening to the radio. Press this button to switch between the tape, CD, and DVD (if equipped) if loaded. The inactive tape, CD, or DVD will remain safely inside the radio for future listening. EJ (Eject): Press this button, located to the left of the CD slot, to eject a CD.
3. Press the pushbutton (1-6) for the CD slot to load or to eject. WAIT will appear on the display. If a CD is already loaded the CD will eject. If the CD slot is empty, LOAD will appear on the display, and a CD can be loaded. 4. Load a CD. Insert the CD partway into the slot, label side up.
R REW (Rewind): Press and hold the down arrow to rewind quickly within a track. Release it to play the passage. The display will show the elapsed time of the track. Q FF (Fast Forward): Press and hold the up arrow to advance quickly within a track. Release it to play the passage.
Rear Seat Entertainment System Your vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicles audio system and includes a DVD radio, a video display screen, two sets of wireless headphones, and a remote control.
Battery Replacement To change the batteries, do the following: 1. Slide open the battery door located on the left side of the headphones. 2. Replace the two AAA batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment.
The RCA jacks are color coded to match typical home entertainment system equipment. The yellow jack (right) is for the video input. The white jack (middle) is for the left audio input.
Video Screen The video screen is located in the overhead console. To use the video screen, do the following: 1. Push forward on the release button on the DVD display console. 2. Pull the screen down, away from you, and adjust its position as desired. When the video screen is not in use, push it up into its locked position.
The DVD radio is only compatible with DVDs authorized for use in the United States and Canada (Region Code 1). The DVD region code is printed on the jacket of most DVDs.
Stopping and Resuming Playback To stop playing a disc, press the stop button on the remote control. To resume playback, press the play/pause button on the remote control. The movie should resume play from where it last stopped if the disc has not been ejected and the stop button has not been pressed twice on the remote control.
Remote Control Buttons O (Power): Press this button to turn the DVD player on and off. v (Title): Press this button to return the DVD to the main menu of the DVD. n , q , p , o (Menu Navigation Arrows): Use the arrow buttons to navigate through a menu.
1 through 0 (Numeric Keypad): The numeric keypad provides the capability of direct chapter, title, and track number selection. } 10 (Double Digit Entries): Press the button, to select chapter, title, and track numbers greater than 9. Press this button before inputting the number.
s (Play/Pause): Press this button to start play of a DVD or CD. Press this button while a DVD or CD is playing to pause it. Press this button again to continue playing the DVD or CD. When the DVD is playing, press the pause button then press the fast forward button.
DVD Radio Error Messages The radio may display one of the following: No Disc: This message will be displayed, if no disc is present when the play, eject, or DVD/AUX button is pressed on the remote control or the eject, RSE, or AUX button is pressed on the radio.
Theft-Deterrent Feature The Radio with Cassette and CD and the Radio with Cassette and Six-Disc CD have a theft deterrent feature. The theft deterrent feature is designed to discourage theft of your vehicle’s radio. It works by using a secret code to disable all radio functions whenever battery power is interrupted.
5. Press the SEEK/SCAN up arrow to make the first digit agree with your code. 6. Press the SEEK/SCAN down arrow to make the second digit agree with your code. 7. Press the TUNE up arrow to make the third digit agree with your code. 8. Press the TUNE down arrow to make the fourth digit agree with your code.
Disabling the Theft-Deterrent Feature Enter your secret code as follows; pause no more than 15 seconds between steps: Preform Steps 1 through 9 from the “Activating the Theft-Deterrent Feature” earlier to enter your secret code. OFF will appear on the display indicating the theft deterrent feature is off.
Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes, or a damaged mechanism. Cassette tapes should be stored in their cases away from contaminants, direct sunlight, and extreme heat.
Care of Your CDs and DVDs Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
✍ NOTES 3-74.
Your Driving, the Road, and Your Vehicle ......... .4-2 Defensive Driving .......................................... .4-2 Drunken Driving ............................................ .4-2 Control of a Vehicle ....................................... .4-5 Braking .
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-11 .
Many adults — by some estimates, nearly half the adult population — choose never to drink alcohol, so they never drive after drinking. For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological and developmental reasons for these laws.
There is a gender difference, too. Women generally have a lower relative percentage of body water than men. Since alcohol is carried in body water, this means that a woman generally will reach a higher BAC level than a man of her same body weight will when each has the same number of drinks.
{ CAUTION: Drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Please do not drink and drive or ride with a driver who has been drinking.
Braking Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time. Average reaction time is about 3/4 of a second.
Anti-lock Brake System (ABS) Your vehicle has anti-lock brakes. ABS is an advanced electronic braking system that will help prevent a braking skid. When you start your engine and begin to drive away, your anti-lock brake system will check itself.
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly.
Traction Control System (TCS) Your vehicle has a traction control system that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
To turn the system off, press the trac switch. The traction control system warning light will come on and stay on. If the system is limiting wheel spin when you press the button, the warning light will come on – but the system won’t turn off right away.
Suppose you are steering through a sharp curve. Then you suddenly apply the brakes. Both control systems — steering and braking — have to do their work where the tires meet the road. Unless you have four-wheel anti-lock brakes, adding the hard braking can demand too much of those places.
An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again.
• Check your mirrors, glance over your shoulder, and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane.
If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, your vehicle may straighten out. Always be ready for a second skid if it occurs. Of course, traction is reduced when water, snow, ice, gravel or other material is on the road.
Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Adjust your inside rearview mirror to reduce the glare from headlamps behind you. • Since you can not see as well, you may need to slow down and keep more space between you and other vehicles.
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can not stop, accelerate or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can not, try to slow down before you hit them. { CAUTION: Wet brakes can cause accidents.
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Some Other Rainy Weather Tips • Turn on your low-beam headlamps — not just your parking lamps — to help make you more visible to others. • Besides slowing down, allow some extra following distance. And be especially careful when you pass another vehicle.
Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip. • Try to use the freeways that rim and crisscross most large cities.
The most important advice on freeway driving is: Keep up with traff ic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-fast or too-slow driving breaks a smooth traff ic flow. Treat the left lane on a freeway as a passing lane.
Before Leaving on a Long Trip Make sure you are ready. Try to be well rested. If you must start when you are not fresh — such as after a day’s work — do not plan to make too many miles that first part of the journey. Wear comfortable clothing and shoes you can easily drive in.
What can you do about highway hypnosis? First, be aware that it can happen. Then here are some tips: • Make sure your vehicle is well ventilated, with a comfortably cool interior. • Keep your eyes moving. Scan the road ahead and to the sides. Check your rearview mirrors and your instruments frequently.
• Know how to go down hills. The most important thing to know is this: let your engine do some of the slowing down. Shift to a lower gear when you go down a steep or long hill. { CAUTION: If you do not shift down, your brakes could get so hot that they would not work well.
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your trunk.
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You will have a lot less traction or “grip” and will need to be very careful.
Remember, unless you have anti-lock, if you brake so hard that your wheels stop rolling, you will just slide. Brake so your wheels always keep rolling and you can still steer. • Whatever your braking system, allow greater following distance on any slippery road.
• Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, floor mats — anything you can wrap around yourself or tuck under your clothing to keep warm.
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can.
Rocking Your Vehicle To Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. You should turn your traction control system off. See Traction Control System (TCS) on page 4-9 . Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible.
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-6 . If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing” following.
Dinghy Towing You may dinghy tow your vehicle from the front following these steps: 1. Set the parking brake. 2. Turn the ignition key to ACC to unlock the steering wheel. 3. Shift your transaxle to NEUTRAL (N). 4. Open the lid on the underhood fuse block and remove the IGN 0/3/CR and IGN 1/2 fuses.
Dolly Towing Your vehicle can be towed using a dolly. To tow your vehicle using a dolly, follow these steps: 1. Put the front wheels on a dolly. 2. Put the vehicle in PARK (P). 3. Set the parking brake and remove the key. 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing.
Tire and Loading Information Label A. Vehicle Capacity Weight A. Vehicle Capacity Weight The Tire and Loading Information label shows the seating capacity and the total weight your vehicle can properly carry. This weight is called the vehicle capacity weight.
The Tire and Loading Information label also gives you the size and recommended inflation pressure for the factory-installed, original equipment tires on your vehicle. For more information on tires and inflation see Tires on page 5-54 and Inflation - Tire Pressure on page 5-61 .
Loading Your Vehicle Item Description Total A Vehicle Capacity Weight for Example 1= 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Carg.
Loading Your Vehicle Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Occupant and C.
The GVWR includes the weight of the vehicle, all occupants, fuel and cargo. Never exceed the GVWR for your vehicle or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. If you do have a heavy load, spread it out. Don’t carry more than 167 pounds (75 kg) in your trunk.
Towing a Trailer { CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured.
If You Do Decide to Pull a Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Hitches It’s important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why you will need the right hitch. Here are some rules to follow: • The rear bumper on your vehicle is not intended for hitches.
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you will want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer.
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle may need a different turn signal flasher and/or extra wiring. Check with your dealer.
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks.
Service ........................................................... .5-3 Doing Your Own Service Work ........................ .5-4 Adding Equipment to the Outside of Your Vehicle ..................................................... .5-5 Fuel ........
Tire Chains ................................................. .5-68 If a Tire Goes Flat ....................................... .5-69 Changing a Flat Tire .................................... .5-70 Compact Spare Tire ..................................
Service Your Saturn retailer knows your vehicle best and wants you to be happy with it. We hope you will go to your retailer for all your service needs. You will get genuine Saturn parts and Saturn-trained and supported service people. We hope you will want to keep your Saturn vehicle all Saturn.
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-10 .
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it. This may cause wind noise and affect windshield washer performance. Check with your retailer before adding equipment to the outside of your vehicle.
Gasoline Specifications It is recommended that gasoline meet specifications which were developed by automobile manufacturers around the world and contained in the World-Wide Fuel Charter which is available from the Alliance of Automobile Manufacturers at www.
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. You should not have to add anything to your fuel.
Filling Your Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
CAUTION: (Continued) This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any “hiss” noise to stop. Then unscrew the cap all the way. Be careful not to spill fuel. Clean fuel from painted surfaces as soon as possible.
Checking Things Under the Hood { CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. { CAUTION: Things that burn can get on hot engine parts and start a fire.
2. Then go to the front of the vehicle and lift up on the secondary hood release lever. 3. Lift the hood, release the hood prop from its retainer and put the hood prop into the slot in the hood. Before closing the hood, be sure all the filler caps are on properly.
Engine Compartment Overview When you open the hood on the 2.2L L4 (L61) engine, you’ll see the following: 5-12.
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-20 for more information. B. Engine Oil Dipstick. See Engine Oil on page 5-16 for more information. C. Engine Oil Fill Cap. See Engine Oil on page 5-16 for more information. D. Power Steering Fluid.
When you open the hood on the 3.0L V6 (L81) engine, you’ll see the following: 5-14.
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-20 for more information. B. Engine Oil Dipstick. See Engine Oil on page 5-16 for more information. C. Engine Oil Fill Cap. See Engine Oil on page 5-16 for more information. D. Brake Master Cylinder Fluid.
Engine Oil Checking Engine Oil It is a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground.
See Engine Compartment Overview on page 5-12 for the location of the engine oil fill cap. Be sure to add enough oil to put the level somewhere in the proper operating range.
• SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, if it is going to be 0°F (–18°C) or above and SAE 5W-30 is not available, you may use SAE 10W-30. These numbers on an oil container show its viscosity, or thickness.
When to Change Engine Oil (GM Oil Life System) Your vehicle has a computer system that lets you know when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably.
What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner.
{ CAUTION: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air, it helps to stop flame if the engine backfires. If it is not there and the engine backfires, you could be burned.
3. Pull the air cleaner/filter box cover out and remove the air filter element from the air filter box. If the element is dirty, you should replace it. If the element is only dusty, it may be cleaned by blowing compressed air through it from the clean side.
Automatic Transaxle Fluid It is not necessary to check the transaxle fluid level. A transaxle fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to retailer’s service department and have it repaired as soon as possible.
What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL ® coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else. { CAUTION: Adding only plain water to your cooling system can be dangerous.
Checking Coolant The surge tank is located on the driver”s side of the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location. { CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Adding Coolant If you need more coolant, add the proper DEX-COOL ® coolant mixture at the surge tank , but only when the engine is cool. See Engine Overheating on page 5-26 for instructions on “How to Add Coolant to the Coolant Surge Tank.” { CAUTION: You can be burned if you spill coolant on hot engine parts.
If Steam Is Coming From Your Engine { CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
If No Steam Is Coming From Your Engine An overheat warning, along with a low coolant light, can indicate a serious problem. See Low Coolant Warning Light on page 3-33 . If you get an engine overheat warning with no low coolant light, but see or hear no steam, the problem may not be too serious.
Cooling System When you decide it is safe to lift the hood, here is what you will see: A. Coolant Surge Tank with Pressure Cap B. Electric Engine Fan { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
The coolant level should be at the COLD line (surge tank seam). If it is not, you may have a leak at the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. { CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
How to Add Coolant to the Coolant Surge Tank Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged. If you have not found a problem yet, check to see if coolant is visible in the surge tank.
{ CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture.
1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise (left) about one-quarter of a turn. If you hear a hiss, wait for that to stop.
Check the level in the surge tank when the cooling system has cooled down. If the coolant is not at the proper level, repeat Steps 1 through 3 and reinstall the pressure cap. If the coolant isn’t at the proper level when the system cools down again, see your retailer.
Windshield Washer Fluid What to Use When you need windshield or rear window (wagon models) washer fluid be sure to read the instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has suff icient protection against freezing.
Brakes Brake Fluid Your brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down.
What to Add When you do need brake fluid, use only DOT-3 brake fluid. Use new brake fluid from a sealed container only. See Recommended Fluids and Lubricants on page 6-12 . Always clean the brake fluid reservoir cap and the area around the cap before removing it.
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking.
Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative ( − ) cable from the battery. This will help keep your battery from running down. { CAUTION: Batteries have acid that can burn you and gas that can explode.
1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle.
4. Open the hoods and locate the batteries. Find the positive (+) and negative ( − ) terminal locations on each vehicle. See Engine Compartment Overview on page 5-12 for more information on location. { CAUTION: An electric fan can start up even when the engine is not running and can injure you.
{ CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged, too.
7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( − ) cable to the negative ( − ) terminal of the good battery.
10. Now start the vehicle with the good battery and run the engine for a while. 11. Press UNLOCK on the RKE transmitter to disarm your security system (if equipped). 12. Try to start the vehicle that had the dead battery. If it won’t start after a few tries, it probably needs service.
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( − ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery.
Headlamps, Front Turn Signal, Sidemarker, and Parking Lamps 1. Open the hood and secure it with the prop rod. 2. Remove push-pin fasteners from grill assembly. 3. Tilt grill assembly forward and lift it up to remove it from the body of the vehicle. 4.
5. Push headlamp housing lever up to disengage headlamp housing from headlamp housing pocket. 6. Turn the bulb socket being replaced counterclockwise one–quarter of a turn while pressing the socket in firmly. Pull the socket rearward until the bulb clears the headlamp housing, and lift it up to access the bulb.
Fog Lamps 1. Reach up from underneath the front body panel and turn the bulb socket counterclockwise one– quarter of a turn while pressing the socket in firmly. Pull the socket rearward until the bulb clears the fog lamp housing. 2. Disconnect the wire connector from the bulb by lifting the lock tab and pulling it away from the plastic base.
Center High-Mounted Stoplamp (CHMSL) (Wagon) 1. Open the liftgate. 2. Remove the center high mounted stop lamp cover by pulling down on the cover edges. 3. Turn the bulb socket being replaced counterclockwise one–quarter of a turn and remove the bulb.
3. Remove fasteners from backside of taillamp housing. 4. Remove taillamp housing from body of vehicle. 5. Turn the bulb socket being replaced counterclockwise one–quarter of a turn while pressing the socket in firmly. Pull the socket rearward until the bulb clears the taillamp housing.
Taillamps, Turn Signal, Stoplamps and Back-up Lamps (Wagon) 1. Open the liftgate. 2. Remove the interior access trim panel. 3. Turn the bulb socket being replaced counterclockwise one–quarter of a turn while pressing the socket in firmly. Pull the socket rearward until the bulb clears the taillamp housing.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking. See “Windshield Wipers, Blade Check” under Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
(A) Tire Size: The tire size code is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail.
(E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance.
(A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat.
Tire Size The following illustration shows an example of a typical passenger car tire size. (A) P-Metric Tire: The United States version of a metric tire sizing system. The letter “P” as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall.
UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire’s traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire.
When to Check Check your tires once a month or more. Don’t forget your compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gage to check tire pressure. You can’t tell if your tires are properly inflated simply by looking at them.
When rotating your tires, always use the correct rotation pattern shown here. Don’t include the compact spare tire in your tire rotation. If you are towing your Saturn vehicle with all four wheels o.
When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following statements are true: • You can see the indicators at three or more places around the tire.
{ CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle.
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance.
Used Replacement Wheels { CAUTION: Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new Saturn original equipment wheel.
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
The following steps will tell you how to use the jack and change a tire. Removing the Spare Tire and Tools (Sedan) The equipment you’ll need is located in the trunk. 1. Open the jack access door on the left side panel of the trunk. 2. Remove the nut that holds the jack in place and remove the jack together with the wheel wrench.
3. Lift the trunk liner and place the plastic hook in the lip of the trunk. 4. Remove the nut that holds down the spare tire. 5. Remove the compact spare tire. See Compact Spare Tire on page 5-81 6. The wheel wrench is held in place by two clips which are attached to the jack.
1. Lift up the spare tire cover by the handle. Fold the side panels in and then attach the cover to the liftgate with the hook provided. 2. Remove the nut that holds down the spare tire. 3. Remove the compact spare tire. See Compact Spare Tire on page 5-81 4.
Removing the Wheel You must take off the wheel cover or hubcap to reach the wheel bolts. For steel wheels with full plastic covers and aluminum wheels with large circular center caps, do the following: 1. Loosen all five hex-shaped plastic caps by turning the wrench counterclockwise.
4. Position the lift head at the jack location nearest the flat tire. Your vehicle has jack notches. Position the jack in the notch near the tire being changed, but make sure all of the jack lift head is touching the jacking flange under the body. Do not place the jack under a body panel.
6. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to fit underneath the wheel well. 7. Remove all of the wheel nuts. 8. Take of f the tire and wheel.
{ CAUTION: Never use oil or grease on wheel bolts. If you do, the wheel bolts might come loose. Your wheel could fall off, causing a serious accident. 10. Place the compact spare tire on the wheel-mounting surface. 11. Reinstall the wheel nuts. Tighten each nut by hand until the wheel is held against the hub.
13. Tighten the wheel nuts firmly in a crisscross sequence, as shown. { CAUTION: Incorrect wheel bolts or improperly tightened wheel bolts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel bolts.
Storing a Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
1. Place the wheel wrench into the clips on the jack. 2. Install the jack in the left side panel of the trunk for sedans or the spare tire compartment for wagons and secure as shown on the jacking instruction label located in the trunk or cargo area. 3.
Compact Spare Tire Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly.
Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flames if you strike a match or get them on a hot part of the vehicle.
• Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn. • If a ring forms on fabric after spot cleaning, clean the entire area immediately or it will set. Using Cleaner on Fabric 1. Vacuum and brush the area to remove any loose dirt.
Cleaning Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. You may have to do this more than once. • Things like tar, asphalt and shoe polish will stain if you do not get them off quickly. Use a clean cloth and vinyl cleaner.
Care of Safety Belts Keep belts clean and dry. { CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish.
Cleaning Aluminum or Chrome-Plated Wheels Your vehicle may be equipped with either aluminum or chrome-plated wheels. Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel.
Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials avaliable from your dealer.
Vehicle Care/Appearance Materials See your Saturn retailer for more information on purchasing the following products. Vehicle Care/Appearance Materials Description Usage Polishing Cloth Wax-Treated Interior and exterior polishing cloth.
Vehicle Care/Appearance Materials (cont’d) Description Usage Wash Wax Concentrate Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Spot Lifter Quickly and easily removes spots and stains from carpets, vinyl and cloth upholstery.
Engine Identification The 8th character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts. Service Parts Identification Label You’ll find this label on your spare tire cover. It’s very helpful if you ever need to order parts.
Power Windows and Other Power Options Circuit breakers in the fuse panel protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed.
Fuses Usage RADIO Audio, OnStar ® , Rear Seat DVD (Option) WIPER Windshield Washers and Wipers (Front) IGN 3 Left Heated Seat Switch, Right Heated Seat Switch, Air Conditioning, Rear Defogger Relay D.
The passenger’s side fuse block is located by the passenger’s right leg. Use a key or a coin to remove the fuse panel door and access the fuses and relays.
Engine Compartment Fuse Block The engine compartment fuse block is located in the forward part of the engine compartment near the battery. Fuses Usage IGN 1/2 Ignition switch IGN 0/3/CR Ignition switc.
Fuses Usage INJ Fuel Injectors (2.2L L4 (L61)) BACK-UP/TURN Backup Lamps, Coolant Level Switch BRAKE Brake Lamps FUEL PUMP Fuel Pump Relay IGN 0 Park Neutral Position Switch, Powertrain Control Module CRUISE SW Cruise Control Switch CONTROLS IGN 1 Cooling Fan Control Module, Powertrain Control Module, Transaxle (2.
Relays Usage A/C Air Conditioning System DRL Daytime Running Lamp HORN Horn MAIN 3.0L V6 (L81) Engine WIPER Wiper System FUEL PUMP Fuel Pump System REAR WIPER Rear Wiper System (Wagon Only) Circuit Breakers Usage WINDOWS/ SUNROOF Power Window Relay, Sunroof (3.
Capacities and Specifications Application Capacities English Metric Air Conditioning Refrigerant R134a 2.1 lbs. 0.95 kg Cooling System 2.2L L4 (L61) Engine 3.0L V6 (L81) Engine 7.4 quarts 8.5 quarts 7.0 L 8.0 L Engine Oil with Filter 5.0 quarts 4.7 L Fuel Tank 15.
Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using Your Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition.
This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will find these limits on the tire and loading information label. See Loading Your Vehicle on page 4-34 . • are driven on reasonable road surfaces within legal driving limits.
Scheduled Maintenance When the Change Engine Oil light comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km).
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. Reset oil life system. See Engine Oil on page 5-16 . An Emission Control Service. •• Visually check for any leaks or damage. See footnote (j). •• Inspect engine air cleaner filter.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (41 500) 50,000 (83 000) 75,000 (125 000) 100,000 (166 000) 125,000 (207 500) 150,000 (240 000) Engine cooling system service (or every 5 years, whichever occurs first). An Emission Control Service.
(c) Visually inspect hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes, fittings and clamps; replace with genuine Saturn parts as needed.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Your Saturn retailer can assist you with these checks and services.
At Least Once a Year Starter Switch Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake.
Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition key to OFF in each shift lever position. • The key should turn to OFF only when the shift lever is in PARK (P). • The key should come out only in OFF.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your retailer. Part Saturn Part Number AC Delco Part Number Engine Air Cleaner/Filter 90571362 — Engine Oil Filter 3.
Engine Drive Belt Routing 2.2L Four Cylinder (L61) Engine 3.0L V6 (L81) Engine 6-14.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-16.
Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-4 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your retailer and to Saturn. Together we are committed to providing our customers with unparalleled service, before, during and after the purchase of a Saturn vehicle, for total customer satisfaction.
If you wish to write to the Saturn Customer Assistance Center, our address is: Saturn Customer Assistance Center 100 Saturn Parkway Mail Code 371-999-S24 Spring Hill, TN 37174-1500 In Canada, write to: Saturn Customer Communication Centre General Motors of Canada Ltd.
You may contact the BBB Auto Line Program by using the toll-free telephone number or by writing them at the following address: BBB Auto Line Program Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800 Arlington, VA 22203-1804 This program is available in all 50 states and the District of Columbia.
Customer Assistance for Text Telephone (TTY) Users To assist owners who have hearing diff iculties, Saturn has installed special TDD (Telecommunication Devices for the Deaf) equipment in its Saturn Customer Assistance Center.
Roadside Assistance Program Security While You Travel For vehicles purchased in the U.S. call 1-800-553-6000 (TTY: 1-800-833-6000). For vehicles purchased in Canada call 1-800-268-6800. As the proud owner of a new Saturn vehicle, you are automatically enrolled in the Saturn Roadside Assistance Program.
In many instances, mechanical failures are covered under Saturn’s Bumper-to-Bumper warranty. However, when other services are utilized, our Roadside Assistance Representatives will explain any payment obligations you might incur.
Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance.
In addition, once GM collects or receives data, GM may • use the data for GM research needs, • make it available for research where appropriate confidentiality is to be maintained and need is shown, or • share summary data which is not tied to a specific vehicle with non-GM organizations for research purposes.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited.
Owner Publications Information on how to obtain product bulletins and as described below is applicable only in the fifty U.S. states and the District of Columbia, and only for cars and light trucks with a GVWR less than 10,000 pounds (4 536 kg). Copies of individual bulletins are also at your participating Saturn retailer.
✍ NOTES 7-12.
A Accessory Power Outlets ................................. 3-16 Activating the Theft-Deterrent Feature ................ 3-69 Adding Windshield W asher Fluid ....................... 5-35 Additives, Fuel ................................................
B Backing Up .................................................... 4-44 Battery .......................................................... 5-39 Battery Replacement ......................................... 2 - 7 Battery Run-Down Protection ............
Child Restraints Child Restraint Systems ............................... 1-42 Infants and Y oung Children ........................... 1-38 Lower Anchorages and T op T ethers for Children (LA TCH System) .......................... 1-50 Older Children .
Customer Assistance Information Customer Assistance for T ext T elephone (TTY) Users ....................................................... 7 - 5 Customer Satisfaction Procedure ..................... 7 - 2 GM Mobility Program for Persons with Disabilities .
E Electrical System Add-On Equipment ...................................... 5-91 Fuses and Circuit Breakers ........................... 5-92 Power Windows and Other Power Options ...... 5-92 Windshield Wiper Fuses ............................... 5-91 Emergency T runk Release Handle (Sedan) .
Fuel (cont.) Filling a Portable Fuel Container ..................... 5 - 9 Filling Y our T ank ........................................... 5 - 8 Fuels in Foreign Countries .............................. 5 - 7 Gage .....................................
I If No Steam Is Coming From Y our Engine .......... 5-28 If Steam Is Coming From Y our Engine ............... 5-27 If the Light Is Flashing ..................................... 3-35 If the Light Is On Steady ................................. 3-35 If Y ou Are Caught in a Blizzard .
Light (cont.) Malfunction Indicator .................................... 3-34 Oil Pressure ............................................... 3-37 Reduced Engine Power ................................ 3-38 Safety Belt Reminder ...........................
Mirrors Automatic Dimming Rearview with Compass and T emperature Display ........................... 2-36 Automatic Dimming Rearview with OnStar ® , Compass and T emperature Display ............. 2-34 Manual Rearview Mirror ..........................
Playing the Radio ........................... 3-42, 3-45, 3-50 Playing the Single CD Player ........................... 3-54 Playing the Six–Disc CD Player ........................ 3-56 Power .........................................................
Reporting Safety Defects Canadian Government .................................. 7-10 Saturn ....................................................... 7-10 United States Government .............................. 7 - 9 Restraint System Check Checking Y our Restraint Systems .
Service ........................................................... 5 - 3 Adding Equipment to the Outside of Y our V ehicle ..................................................... 5- 5 Doing Y our Own Work ................................... 5 - 4 Engine Soon Light .
Buying New Tires ........................................ 5-64 Chains ....................................................... 5-68 Changing a Flat T ire .................................... 5-70 Compact Spare Tire .....................................
V ehicle Storage .............................................. 5-40 V entilation Adjustment ...................................... 3-24 Video Screen ................................................. 3-62 Visor V anity Mirrors ........................
Een belangrijk punt na aankoop van elk apparaat Saturn 2004 L-Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Saturn 2004 L-Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Saturn 2004 L-Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Saturn 2004 L-Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Saturn 2004 L-Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Saturn 2004 L-Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Saturn 2004 L-Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Saturn 2004 L-Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
