Gebruiksaanwijzing /service van het product 113.21371 van de fabrikant Sears
Ga naar pagina of 24
MODEL NO. ]]3.21371 DRILL PRESS ONLY 113.213710 DRI LL PRESS WITH 1/2 HP MOTOR Serial Number ...................... Model and serial number may be found at the rear of the head. You should record both model and serial number in a safe place for future use.
FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES.
additionam safety instructions for drill presses WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR DRILL PRESS UNTIL iT IS COMPLETELY ASSEMBLED AND iNSTALLED ACCORDING TO THE INSTRUCTOONS . .. AND UNTaL YOU HAVE READ AND UNDERSTAND THE FOLLOWING: 1.
additional safety instructions for drill presses WEAR YOUR The operation of any power tool can result in foreign objects being thrown into the _yes, which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87,1 (shown on Package) before commencing power tool operation.
motor specifications and electrical requirements MOTOR SPECRFICATIONS This drill press is designed to use a 1725 RPM motor only. Do not use any motor that runs faster than 1725 RPM. It is wired for operation on 1!0-120 volts, 60 Hz., alternating current.
assembly WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED, 1. Unwind the power cord. 2. Make sure the quill lock handle is tight. 3. Stand on, the left side of the drill press and LOOSEN the HEAD LOCK HANDLE.
SPINDLE NOSE LOCKING COLLAR 2. Apply a light film of oil such as Sears household oil to the spindle nose. 3. Place the chuck on the spindle nose and screw the locking collar up as far as it will go. CHUCK 4. Insert a piece of 1/4" dia. STEEL ROD in to one of the holes in the chuck body.
assembly INSTALLING THE DEPTH STOP 1. Screw the THUMB SCREW partways into the DEPTH POINTER. 2. Place the DEPTH POINTER SHOE inside the pointer. 3. Loosen QUILL LOCK HANDLE ... lower the quill about two inches. 4. Slide the pointer and shoe onto the FEED STOP ROD and tighten the thumb screw.
9. Gently push down on the FEED HANDLES until the head raises upwards as far as it will go. 10, TIGHTEN THE HEAD LOCK HANDLE AND THE QUILL LOCK HANDLE. 11. HOLD onto the Feed Handle and UNLOCK the quill lock handle. 12, Let the quill return to the UP position in the head.
assembty NOTE: When using motors which have Y2" dia. shafts, place the adapter sleeve (furnished with the motor) on the shaft so that the slot in the sleeve is over the flat spot. 4. Insert the shaft key (furnished with motor) into the grooves in the shaft and pulley so that the end of the key is even with the end of the shaft, 5.
5, Remove the belt guard by "pushing in" on the two "links". 6, Place motor on drill press ... screw the pivot screws into the holes. NOTE: DO NOT SCREW THEM IN TOO TIGHT ,.. EXCESSIVE TIGHTNESS COULD BEND THE MOTOR MOUNT. 7, Find two 5/16 in-18 hex.
assembly INSTALLING AND TENSIONING BELT 1. Place a straightedge such as a piece of wood, metal or framing square across the pulleys. 2. Move the motor UPWARDS until the pulleys are IN LINE ... tighten the motor mounting nuts with a ½ in. wrench. 3. 4, 5.
getting to know your drill press -4.-- SPLINES (GROOVES) SPINDLE QU ILL "_ QUILL AND SPINDLE ASSEMBLY INSIDE OF DRILL PRESS SWITCH KEY CHUCK _,.__.
getting to know your drill press HEAD LOCK HANDLE ... locks the head to the column. ALWAYS have it locked in place while operating the drill press. HEAD SUPPORT COLLAR . .. prevents the head from dropping when the head lock handle is loosened. ALWAYS have the collar LOCKED into position against the UNDERSIDE of the head .
REMOVING THE CHUCK. 1, 2. Insert apiece of 1/4 in. alia. steel rod in one of the holes in the chuck body, insert the CHUCK KEY into one of the hoIes in the collar ... turn it in the direction of arrow until LOOSE. Continue to turn it until the chuck is released.
basic drill press operation We recommend the following instructions for operating your drill press so that you get the best results and to minimize the likelihood of personal injury. WARNING: FOR YOUR OWN SAFETY, ALWAYS OBSERVE THE FOLLOWING SAFETY PRECAUTIONS.
HOLE LOCAT!ON Make a DENT in the workpiece whereyou want the hole • • . using a CENTER PUNCH or a SHARP NAIL. Before turning the switch ON, bring the drill down to the workpiece lining it up with the hole location. FEEDING Pull down on the feed handles with only enough effort to allow the drill to cut.
maintenance WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "'OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR DRILL PRESS, Frequently blow out any dust that may accumulate inside the motor. A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean.
trouble shooting WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING. TROUBLE Noisy Operation Drill Burns. Drill leads off... hole not round. PROBABLE CAUSE 1. Incorrect belt tension 2.
PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.21371 & 113.213710 13 14 (SEE FIGURE 3) i 38 18 52 51 Figure I 37 WIRING DIAGRAM ,=111 _0 Q.
PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.21371 & 113.213710 Always order by Part Number - not by Key Number FIGURE 1 PARTS LIST Key No. 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 35 36 37 Part No.
PARTS LIST FOR CRAFTSMAN DRILL PRESS ,___i_ 5 MODEL NO. 113.21371 & 113.213710 6 4 11-- ,4d; 15-----._ 16,----..-"_ Figure 2 FIGURE 2 PARTS LIST Key Part No.
Q "+-------3 7 / / / / PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.21371 & 113.213710 / / / / / / ,/ / / / / FIGURE 3 - 71075 SPINDLE ASSEMBLY, STOP Key Part No.
SERVICE MODEL NO. 113.2137] DRILL PRESS ONLY 113.2!3710 DRILL PRESS WITH 1/2 HP MOTOR HOW TO ORDER REPAIR PARTS ] 5°]/2 [NCH DRILL PRESS Now that you have purchased your 15-1/2 inch drill press should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
Een belangrijk punt na aankoop van elk apparaat Sears 113.21371 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears 113.21371 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears 113.21371 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears 113.21371 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears 113.21371 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears 113.21371 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears 113.21371 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears 113.21371 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
