Gebruiksaanwijzing /service van het product 200.71232 van de fabrikant Sears
Ga naar pagina of 16
Sears, Roebuck and Co., Hoffman Est ates, IL 60179 U.S.A. B A TTER Y CHARGER 60/20/2 Amp Fully A utomatic 275/125 AMP ENGINE ST AR TER With Batter y T ester Model No. 200.71232 O WNER’S MANU AL 00-99-000314/0103 CA UTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product.
.
1 W arranty .................................................................... 1 Important Saf ety Instructions ................................. 2 P arts .......................................................................... 3 Before Using Y our Battery Charger .
2 Help us help you Remember: • Place charger as far away from battery being charged as the charger cables will permit. • Do not expose charger to rain or snow. • Never charge a frozen battery. If battery fluid (electrolyte) becomes frozen, bring battery into a warm area to thaw before you begin charging.
3 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List DieHard 71232 Item Description Part Number 1. Plastic Top 3799001210 2.
4 To attach the axle assembly: 1. Remove charger from packing materials and place upside down on a flat surface. Attach mounting foot and secure with the two 1/4-20 thread cutting screws. 2. Hold axle upright on floor or work surface. Then, using a hammer, tap one of the plastic hubs onto the top end of the axle.
5 3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
6 A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician.
7 For best results from your battery charger, learn to use it properly. This section tells how to set the controls, charge a battery in or out of the vehicle, use the ENGINE START feature and test the battery. Using Y our Battery Charger All the controls for your charger are located on the front of the unit.
8 • TIME: To select a charging time, you must be in the MANUAL mode and have selected a charge rate. Touch the TIME pad until the desired time shows on the meter. The following chart shows the amount of time available for each charge rate and the amount of time, in hours, added for each touch of the TIME pad.
9 Charging Y our Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads carefully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury.
10 8. For automatic charging, touch AUTO then a charge-rate pad 2, 20, or 60 Amps. The charging will stop when the battery is fully charged. 9. For manual charging, touch a charge rate pad then select a charge time up to 18 hours. If more than 135 minutes of charging time is needed, reset the time when the original time runs out.
11 Calculating charge times • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC) . • NR means that the charger setting is NOT RECOM- MENDED . Find your battery’s rating on the chart below and note the charge time given for each charger setting.
12 A minimal amount of care can keep your battery charger working properly for years. 1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. 2. Coil the input and output cords neatly when storing the charger.
13 T roubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check for poor connections at battery and frame.
For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm CT Monday through Friday. 1-800-SEARS-64 (1-800-732-7764). For repair parts or the location of a Sears Parts and Repair Center call: 1-800-4-MY-HOME ® (1-800-469-4663).
Een belangrijk punt na aankoop van elk apparaat Sears 200.71232 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears 200.71232 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears 200.71232 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears 200.71232 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears 200.71232 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears 200.71232 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears 200.71232 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears 200.71232 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
