Gebruiksaanwijzing /service van het product 917.299642 van de fabrikant Sears
Ga naar pagina of 36
SWAURS OWNER'S MANUAL MODEL NO, 917.299642 Caution: Read and follow all Safety Rules and Instructions Before Operating This Equipment £RI:IFTSMI:IN 4.0 HORSEPOWER 14 INCH TINE WIDTH COUNTER ROTATING TINES REAR TINE TILLER Assembly Operation Maintenance Service and Adjustment Repair Parts Sears, Roebuck and Co.
SAFETY RULES Safe Operation Practices for Walk-Behind Powered Rotary Tillers & TRAINING - Read the operating and service instruction manual carefully.
CONGRATULATIONS on your purchase of a Sears Craftsman Tiller° it has been des=gned, engineered and manufactured to give you the best possible dependability and performance.
TABLE OF CONTENTS , iii1, ,Jl,Jll,,,Jlll,,J i J, i, ,,ul Jl, i,ii,llll,ll,, ii, u,lll iin i ii i i i i i i i SAFETY RULES ............................................................................ 2 CUSTOMER RESPONSIBILITIES ........................
TILLER ACCESSORIES THESE ACCESSORIES WERE AVAILABLE WHEN THE TILLER WAS PURCHASED. THEY ARE ALSO AVAILABLE AT MOST SEARS RETAIL OUTLETS, CATALOG AND SERVICE CENTERS.
ASSEMBLY TO ASSEMBLE YOUR TILLER YOU WILL NEED: (1) utility knife (1) wire cutter (1) tire pressure gauge (1) pair of pliers (1) screwdriver (1) 9/16" wrench (1) ratchet (1) socket extension (1) 9/16" socket OPERATOR'S POSITION The right hand (RH.
ASSEMBLY UNPACKING CARTON BE CAREFUL OF EXPOSED STAPLES WHEN HANDLING OR DISPOSING OF CARTONING MATERIAL. .... H ,H, CAUTION: WHEN UNPACKING AND ASSEMBLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES,, . While holding Handle Assembly, cut Cable Ties secur- ing Handle Assembly to Top Frame and Depth Slake° Let Handle Assembly rest on Tiller.
ASSEMBLY CONNECT SHIFT ROD , Insert one end of Shift Rod (Fig 6) into hole of Shift Lever Indicator.. • Swing Shift Rod to the right side of Tiller and insert one of two Hairpin Clips through hole of Shift Rod.
- illl i lllU ill LLU IJLIIILILLII,,, " .......... . II JlLILll i ,,.,... Illl ILLJLJLJ I, OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.
OPERATION The operationof any Tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your Tiller and while tilling.
OPERATION STOPPING TINES AND ENGINE . TILLER MOVEMENT AND TINES WILL STOP WHEN DRIVE CONTROL BAR iS RELEASED. • Move Shift Lever Indicator to "N" Neutral position., • To stop Engine, move Throttle Control to "STOP" posi- tion. TURNING • Release the Drive Contro! Bar.
OPERATION H, FILL FUEL TANK • TO fill Fuel Tank (Fig 16), use fresh, clean regular unleaded automotive gasoline Capacity is about 2 quarts_ FILL TO WITHIN 1/2 INCH OF TOP OF FUEL TANK TO PREVENT SPILLS AND TO ALLOW FOR FUEL EXPAN- SION. IF GASOLINE IS ACCIDEN- TALLY SPILLED, MOVE MACHINE AWAY FROM AREA OF SPILL.
OPERATION . For easier handling of your Tiller, leave about 8 inches of untilled soil between the first and second tilling passes. The third pass will be between the first and second (Fig. 17). OUTER VIEW OF TIRE _ _ ,_ _'_ HAIRPIN CLIP FIGURE 17 • Do not lean on the Handle.
i, illllllllllll ii i i i ii i i i i i iillllll MAINTENANCE i ............ DISCONNECT SPARK PLUG WIRE FROM SPARK PLUG BEFORE PER- FORMING ANY MAINTENANCE (EX* CEPT CARBURETOR ADJUSTMENT ) TO PREVENT ACCIDENTAL START- ING OF ENGINE. PREVENT FIRES! KEEP THE ENGINE FREE OF GRASS, LEAVES, SPILLED OIL, OR FUEL.
MAINTENANCE ENGINE LUBRICATION Your four cycle Engine will normally consume some oil, therefore check Engine oil level regularly--approximately every five hours of operation and before each usage. Stop Engine and wait several minutes before checking oii level, With Engine level the oil must be even with oil fill (Fig.
................................. ,,,,,,,,,,, SERVICE RECOMMENDATIONS LUBRICATION CHART- OIL PIVOT POINTS USE SAE 30 OIL TH ROIRLE CONTROL IDLER BRACKET SHIFT LEVER DEPTH STAKE PIN WHEEL HUB FIGURE 25.
SERVICE AND ADJUSTMENTS POSITION HANDLE Select Handle height suitable for you and your tilling conditions,Handle heightwill change when Tiller digs into the soilo TO ADJUST HANDLE: • First loosen Ha.
SERVICE AND ADJUSTMENTS ,ll, GROUND DRIVE BELT REPLACEMENT - Remove Hairpin Clip and Retaining Pin from Hub of left hand Wheel Pull Wheel out from Tiller about I inc_h__ - Remove Belt Guard by removing two (2) Cap Nuts, one (1) Hex Nut and three (3) Washers so that the Belt Guard can slide straight out away from the Engine (Fig.
SERVICE AND ADJUSTMENT TINE REPLACEMENT STOP THE ENGINE AND REMOVE THE SPARK PLUG WIRE FROM THE SPARK PLUG BEFORE CLEANING OUT THE TINES BY HAND. USE CAU* TION : TINES ARE SHARP. A badly worn Tine causes your Tiller to work harder and dig more shallow.
IIIlUl II SERVICE AND ADJUSTMENT CARBURETOR NOTE: A dirty Air Cleaner will cause the Engine to run rough. Be sure Air Cleaner is clean before adjustments_ Factory settings are satisfactory for most applications and conditions, if adjustments are needed, proceed as follows: Never attempt to change maximum Engine speed.
STORAGE STORAGE Keep your Tiller in a weatherproof, dry building_ To avoid Engine problems, the fuel system should be emptied be- fore storage of 30 days or longer° • Drain Fuel Tank; run Engine until gasoline in Carbure- tor is used.. . While Engine is still warm, drain oil from Engine.
22.
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 HANDLE ASSEMBLY 12 "%::.', 32---_ 26 16 KEY PART NO, NO. 1 110707X 2 110674X 3 110673X 4 110672X 5 6712J 6 120431X 7 121859X 8 .
REPAIR PARTS 4 H,P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 MAINFRAME, LEFT SIDE 3 12 40 13 KEY PART NO. NO. 1 STD541431 * 2 STD551137" 3 STD541037" 4 74930576 5 1572H 6 110111X 7 STD5325.
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 MAINFRAME, RIGHT SIDE 2 12 13 9 KEY PART DESCRIPTION NO, NO. t --- Decal, O,P.E.I 2 STD541431" Decal, Operations and Lubrication 3 7.
REPAIR PARTS 4 H.P, CRAFTSMAN TILLER - MODEL NUMBER 917.299642 TRANSMISSION 25 24 2G 24 24 43 44 45 46 47 48 > 24 KEY PART NO. NO. 1 121146X 2 121147X 3 106211X 4 5020J 5 !370H 6 102113X 7 102110X .
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 TINE SHIELD ,J %, 1 2 23 13 7 24 22 11 27 28 19 KEY PART NO. NOr 1 98000129 2 104086X361 3 104085X361 4 8393J 5 12000036 6 STD533107".
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 TINES 1 t T 10 KEY PART DESCRIPTION NO. NO. 1 4459J Tine L H. Outer 2 74610616 Bolt, Hex 3/8 - 24 x 1 3 STD551137" Washer, Lock 3/8 4 73610600 Nut, Hex 3/8 - 24 5 4929H Retaining Pin 6 102170X Hub, Assembly L.
REPAIR PARTS 4 H.P, CRAFTSMAN TILLER - MODEL NUMBER 917.299642 ENGINE - BRIGGS & STRATTON-- MODEL NUMBER 112202, TYPE NUMBER 0847-01 ENGINE, RIGHT SIDE 22 10 * REQUIRES SPECIAL TOOLS TO INSTALL, SEE REPAIR INSTRUCTION MANUAL° Assemblies include all parts shown in frames.
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 ENGINE - BRIGGS & STRATTON -- MODEL NUMBER 112202, TYPE NUMBER 0847-01 ENGINE, REAR 3 16 41 (_29 28 14 10 11 39 4O 47 37 23 54 53 51 .
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 ENGINE - BRIGGS & STRATTON - MODEL NUMBER 112202, TYPE NUMBER 0847-01 ENGINE, REAR KEY PART DESCRIPTION KEY PART DESCRIPTION NO.
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 ENGINE- BRIGGS & STRATTON -- MODEL NUMBER 112202, TYPE NUMBER 0847.01 ENGINE, INTERNAL PARTS 6 5 7 72, 76 14 74 75 49 54 134 GASKET SET] @_4s 46 38 * SPECIAL TOOLS REQUIRED TO INSTALL, SEE REPAIR INSTRUCTION MANUAL t71 DECAL KIT 1 8 23 24 25 L 23 26.
REPAIR PARTS 4 H.P. CRAFTSMAN TILLER - MODEL NUMBER 917.299642 ENGINE - BRIGGS & STRATTON -- MODEL NUMBER 112202, TYPE NUMBER 0847-01 ENGINE, INTERNAL PARTS KEY PART DESCRIPTION KEY PART DESCRIPTION NO.
lll£Vl@l 1II@?!i8 34.
IIIi£VIGII 111)1118 35.
OWNERS MANUAL MODEL NO. 917.299642 HOW TO ORDER REPAIR PARTS £RRFTXMaN 4.0 POWER 14 INCH TI WIDTH COUNTER ROTATING TINES R AR TINE TILLER Each Tiller has its own model number,, Each Engine has its own model number,_ The Model Number for your Tiller will be found on a plate attached to the top of the Transmission.
Een belangrijk punt na aankoop van elk apparaat Sears 917.299642 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears 917.299642 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears 917.299642 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears 917.299642 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears 917.299642 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears 917.299642 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears 917.299642 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears 917.299642 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
