Gebruiksaanwijzing /service van het product RO 2000 van de fabrikant Sears
Ga naar pagina of 20
WaterWorks TM Undersink Reverse Osmosis HOME DRINKING WATER SYSTEM Model RO 2000 Installation Operation Maintenance Repair Parts IF YOU HAVE QUESTIONS WHEN INSTALLING, OPERATING AND MAINTAINING YOUR REVERSE OSMOSIS SYSTEM... CALL TOLL FREE 1-800-86 WATER System Tested and Certified to ANSI/NSF Standard 58.
- TABLE OF CONTENTS - Safety Guides ................................................ 2-3 What Your Home Drinking Water System Will Do ..................... 3 Things To Check Before You Start To Install ....................... 4-5 How To Install Your Home Drinking Water System .
- SAFETY GUIDES - DO NOT USE THE SYSTEM ON MICROBIOLOGICALLY UNSAFE WATER, OR WATER OF UNKNOWN QUALITY WITHOUT ADEQUATE DISINFECTION BEFORE OR AFTER THE SYSTEM. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
- THINGS TO CHECK BEFORE YOU START TO INSTALL - • PARTS IN THE SHIPPING CARTON -- Unpack the carton carefully so needed parts are not discard- ed by mistake. Included are: _ _ WATER (_ _ _ t SUPPLY _,/_1 _b') _tl SADDLE VALVE _,,_ --. RO , I ASSEMBLY _ .
- THINGS TO CHECK BEFORE YOU START TO INSTALL - REMOTE LOCATION -- You can install the RO assembly or water supply saddle valve in another place away from the RO faucet (please see page 2O). • REPLACING ANOTHER RO SYSTEM -- We suggest you remove all parts of another RO system, and use everything included with your new RO system.
- HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM - STEP 1 -- INSTALL THE COLD WATER SUPPLY SADDLE VALVE (FIG. 2) • Install this valve on the COLD water pipe to the kitchen sink (FIG. 2). • This valve has a cutting pin and will make its own hole in copper or plastic pipe.
- HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM - INSTALL THE DRAIN ADAPTER • Use FIG. 3 and the following guides. Note: Consult a plumber if you are not familiar with plumbing procedures• 1. Use a ferrule and nut to assemble the drain tubing connector to the drain adapter.
- HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM - ASSEMBLE FAUCET AND INSTALL - continued B. ASSEMBLE FAUCET (FIG. 4) 1. Remove the hex nut, and all other parts shown in the dotted line box, FIG. 4. 2. Insert the faucet stud through the top gasket and faucet base.
- HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM - tighten the nut. NOTE: Cut tubing as needed for neat appearance, but keep long enough to alllow easy service of the RO system. 7. If needed, cut the 1/4" tubing (marked "1/4" BARB ON FAUCET") to length.
- HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM - MAKE REMAINING RO CONNECTIONS - continued B. CONNECT TUBING, FAUCET TO DRAIN TUB- ING CONNECTOR Looking at FIG. 7 and page 16, run the 3/8" x 27" tubing from the RO faucet, to the connector at the adapter you installed in the sink drain pipe.
- HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM - the RO system. At that time, carefully check all fit- tings and tubing connections for any water leaks. Correct leaks if any are found. E. IMPORTANT PURGING INSTRUCTIONS: The RO cartridge contains a food grade preser- vative that you should clean from it before using the system.
- HOW YOUR HOME DRINKING WATER SYSTEM WORKS - POSTFILTER - continued water. High quality drinking water flows from the postfilter and to the faucet. NOTE: Before going to the faucet, product water passes through the electronic box and remaining TDS is measured by a sensor.
- CARE OF YOUR HOME DRINKING WATER SYSTEM - PREFILTER CARTRIDGE - You must replace the prefilter cartridge often to protect the RO mem- brane from being destroyed by chlorine, and/or from plugging with sediments from the water supply. If you have chlorine in the water, replace the cartridge at least every 6 months.
- CARE OF YOUR HOME DRINKING WATER SYSTEM - RO MEMBRANE CARTRIDGE - The useful life of the membrane cartridge depends mostly on the pH (see page 17) of your supply water. The lower the pH, the longer the membrane will last. For ex- ample, if the feed water has a pH of about 7.
- CARE OF YOUR HOME DRINKING WATER SYSTEM - 7. Install the RO housing, push downward and rotate 900 clockwise to lock in place. 8. Replace the tank shutoff valve and rotate 900 to lock. 9. Using the o-ring seal, replace the vacuum relief valve. 10. DO THE SANITIZING AND PURGING PRO- CEDURES, PAGE 10.
- CARE OF YOUR HOME DRINKING WATER SYSTEM - RO CARE GUIDE MODEL RO 2000 WITH MONITOR IMPORTANT: BEFORE DOING THE FOLLOWING MAINTENANCE, BE SURETO RELIEVE PRESSURE AND ALLOW AIR TO ENTER THE TANK, STEPS 1, 2 AND 3, PAGE 12.
- DIMENSIONS / SPECIFICATIONS - • =-- 8_ 1/8,,--.-_ 21" Supply water pressure limits ...................................... 40-125 PSI Supply water temperature limits ..................................... 40-100OF Maximum total dissolved solids (TDS) .
- REPAIR PARTS - WaterWorks _ I 1 I O I I HOME DRINKING WATER SYSTEM Undersink Reverse Osmosis MODEL RO 2000 ] I 36 -----_(_ DRAIN I ADAPTER I 35 ---'-'-"_(_;J[ I"'---,_ 5 34 "'"""_ _ 33 .
- REPAIR PARTS - WaterWorks TM HOME DRINKING WATER SYSTEM Undersink Reverse Osmosis MODEL RO 2000 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART NUMBER 7205465 12606.
- REMOTE INSTALLATION LOCATION - INSTALLING RO ASSEMBLY, AND/OR SUPPLY SADDLE VALVE IN REMOTE LOCATION Longer lengths of tubing are available from Sears (see page 19) for installingthe RO assembly, and/or water supply saddle valve away from the RO faucet.
Een belangrijk punt na aankoop van elk apparaat Sears RO 2000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears RO 2000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears RO 2000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears RO 2000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears RO 2000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears RO 2000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears RO 2000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears RO 2000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
