Gebruiksaanwijzing /service van het product AR-151 van de fabrikant Sharp
Ga naar pagina of 52
MODEL AR-151 • GETTING STARTED • MAKING COPIES • SPECIAL FUNCTIONS • SUPPLIES AND USER MAINTENANCE • COPIER TROUBLE? • APPENDIX • OPTIONAL EQUIPMENT 3 12 19 22 26 33 36 DIGITAL LASER COP.
FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit. Model Number Serial Number Date of Purchase Place o.
1 CONTENTS 1 GETTING ST ARTED INTRODUCTION 3 CA UTIONS 4 MAIN FEA TURES 5 P AR T NAMES 6 OPERA TION P ANEL 7 COPIER INST ALLA TION 8 CA UTIONS ON HANDLING 9 LOADING COPY P APER 10 2 MAKING COPIES NORM.
2 5 COPIER TROUBLE? MISFEED REMO V AL 26 – A Misf eed in the paper f eed area 27 – B Misf eed in the fusing area 27 – C Misf eed in the tr ansport area 28 DEVELOPER REQUIRED 29 MAINTENANCE REQUI.
3 1 Getting started GETTING ST AR TED This chapter provides basic inf ormation f or using the copier . INTRODUCTION This copier has been designed to provide intuitive operating ease while requiring a minimum amount of space. T o get full use of all copier f eatures, be sure to f amiliarize yourself with this manual and the copier .
4 1 Getting started CA UTIONS F ollow the cautions below when using this copier . ● The fusing area is hot. Exercise care in this area when removing misf ed paper . ● Do not look directly at the light source. Doing so ma y damage y our e y es . ● Do not s witch the copier rapidly on and off .
5 1 Getting started MAIN FEA TURES High-speed laser copying ● Since warm-up time is zero , cop ying can be star ted immediately after the power s witch is tur ned on. ● First-copy time is only 9.6 seconds (normal mode). ● Copying speed is 15 copies/min.
6 1 Getting started P AR T NAMES 1-B T oner car tridge lock release le ver T oner car tridge T ransfer charger P aper feed roller Fusing unit release le ver Charger cleaner Original table Operation pa.
7 1 Getting started OPERA TION P ANEL Exposure mode selector key and indicators Use to sequentially select the exposure modes: A UT O , MANU AL or PHO T O . Selected mode is shown b y a lit indicator . (p. 14) Light and dark keys and e xposure indicators Use to adjust the MANU AL or PHO T O exposure level.
8 1 Getting started COPIER INST ALLA TION Improper installation ma y damage the copier . Please note the f ollowing during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may f or m inside the copier .
9 1 Getting started 8"(20 cm) 8"(20 cm) 4" (10 cm) 4" (10 cm) COPIER INST ALLA TION Be sure to allow the required space around the machine for servicing and proper ventilation. A small amount of ozone is produced within the copier during operation.
10 1 Getting started LO ADING COPY P APER Raise the handle of the paper tra y and pull the paper tr a y out until it stops . Adjust the paper guides on the paper tra y to the copy paper width and length. Squeeze the lever of paper guide and slide the guide to match with the width of the paper .
11 1 Getting started LO ADING COPY P APER Gently push the paper tra y back into the copier . After loading cop y paper , to cancel the blinking “P” without restar ting copying, press the clear ( ) ke y . The “P” in the display will go out and the ready ( ) indicator will light up.
12 2 Making copies MAKING COPIES This chapter describes basic copying functions and some other cop ying functions using the b ypass tra y . NORMAL COPYING Ensure that paper of the desired size is set in the paper tr ay . See page 10, LO ADING COPY P APER .
13 2 Making copies NORMAL COPYING Tens digit Units digit Open the original cover . Place the original face down on the original tab le. Align it with the or iginal scale and the centering ( ) mark. mark Original scale Gently close the original cov er .
14 2 Making copies Press the print ( ) k e y . ● T o display the number of copies made in a contin uous r un, press the left cop y quantity ke y . ● T o stop copying in the middle of a run, press the clear ( ) ke y . Copying will stop and the number in the display will be reset to “0”.
15 2 Making copies Press the e xposure mode selector ke y to select the manual ( ) mode or photo ( ) mode. Use the light ( ) and dark ( ) keys to adjust the exposure level. If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously .
16 2 Making copies Preset reduction and enlargement ratios are: 50%, 64%, 78%, 129%, and 200% When a zoom ( or ) k ey is pressed, the ZOOM indicator will light up and the zoom ratio will be displayed in the displa y . T o decrease or increase the zoom ratio rapidly , press and hold down the or ke y .
17 2 Making copies T o close the bypass tra y , perform step1 and then step 2 in the illustration and push the round projections at the right of the tray until the tray clicks into place. Set the paper guides to the copy paper width. Insert the copy paper (print face down) all the wa y into the bypass tra y .
18 2 Making copies Place the first original on the original table and mak e a cop y . The first cop y can be made using either the paper tra y or the bypass tra y . Replace the first original with the second original on the original table and close the original cov er .
19 3 Special functions SPECIAL FUNCTIONS This chapter describes the special functions of this copier . Use these functions as needed. DESCRIPTION OF SPECIAL FUNCTIONS T oner save mode (page 19) Reduces toner consumption by approximately 10%.
20 3 Special functions T ONER SA VE MODE Press and hold down the e xposure mode selector ke y for appro ximately 5 seconds. The manual ( ) indicator will go out and the photo ( ) indicator will begin to blink. The exposure indicator mark ed “5” will light up, indicating the standard toner mode is active .
21 3 Special functions USER PROGRAMS Press the print ( ) ke y . The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the displa y . Select the desired parameter using the right cop y quantity ( ) ke y .
22 4 Supplies and user maintenance SUPPLIES AND USER MAINTENANCE This chapter describes how to replace the toner car tr idge. T ONER CAR TRIDGE REPLA CEMENT When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon.
23 4 Supplies and user maintenance T ONER CARTRIDGE REPLA CEMENT Remov e the toner car tridge from the bag. Hold the cartr idge on both sides and shake it horizontally f our or five times . 4 or 5 times Gently inser t the toner car tridge along the guides until it locks in place while pushing the lock release le ver .
24 4 Supplies and user maintenance T oner car tridge life T o find out the approximate quantity of toner remaining, f ollo w the procedure below . Press and hold down the light ( ) and dark ( ) k eys simultaneously f or more than 5 seconds until all the alar m indicators ( , , and ) b link and “– –” appears in the displa y .
25 4 Supplies and user maintenance USER MAINTENANCE T ransfer charger If copies star t becoming streaky or blotch y , the transfer charger ma y be dir ty . Clean the charger using the follo wing procedure. T ur n the power s witch off . Ensure that the bypass tray is open and then open the side cover while pressing the side cover open button.
26 5 Copier trouble? COPIER TR OUBLE? This chapter describes misfeed removal and troubleshooting. MISFEED REMO V AL When the misfeed ( ) indicator b links or blinks in the displa y , the copier will stop because of a misfeed. If a misf eed occurs when using the SPF , a number ma y appear in the displa y after a minus sign.
27 5 Copier trouble? MISFEED REMO V AL A Misfeed in the paper feed area Gently remov e the misfed paper from the paper f eed area as shown in the illustration. When blinks in the display and the misfed paper is not seen from the paper feed area, pull out the paper tra y and remov e the misf ed paper .
28 5 Copier trouble? MISFEED REMO V AL Gently remov e the misf ed paper from under the fusing unit as shown in the illustration. If the paper cannot be remov ed, proceed to “ C Misfeed in the transpor t area ”. The fusing unit is hot. Do not touch the fusing unit when removing misfed paper .
29 5 Copier trouble? Push gently on both sides of the front cov er to open the cov er . Rotate the f eeding roller in the direction of the arrow and gently remov e the misfed paper from the e xit area.
30 5 Copier trouble? TR OUBLESHOO TING If any prob lem occurs , check the list belo w bef ore contacting the SHARP service center . See page: - 12 - - 13 19 19 32 15 24 15 Solution Copier does not operate . Blank copies Copier plugged in? Prob lem P ossible cause Plug the copier into a grounded outlet.
31 5 Copier trouble? ST A TUS INDICA T ORS When the f ollowing indicators light up or blink on the oper ation panel or the follo wing alphanumeric codes appear in the displa y , solv e the problem immediately ref er ring to both the table below and the rele v ant page.
32 5 Copier trouble? A UT OMA TIC EXPOSURE ADJUSTMENT The automatic e xposure le v el can be adjusted to suit your cop ying needs . Press the e xposure mode selector k e y to select the photo ( ) mode. Press and hold down the e xposure mode selector ke y for appro ximately 5 seconds.
33 6 Appendix APPENDIX SPECIFICA TIONS T ype Digital laser copier , desk-top type Copy system Dr y , electrostatic transfer Or iginals Sheets, bound documents Original size Max. 10" x 14" Cop y sizes 3-1/2" x 5-1/2" to 8-1/2" x 14" (F eed cop y paper lengthwise only .
34 6 Appendix SPECIFICA TIONS Optional equipment Single pass f eeder (AR-SP3) 250-sheet paper f eed unit (AR-DE9) F acsimile e xpansion kit (AR-FX3) GDI expansion kit (AR-PG1) PCL expansion kit (AR-PB9) First-copy time ma y diff er depending on operating conditions, such as power-supply v oltage and room temperature.
35 6 Appendix * Do not use env elopes that hav e metal clasps, plastic snappers, string closures, windows , linings, self-adhesiv e, patches or synthetic mater ials. These will cause physical damage to the copier . ** F or paper weighing from 28 to 34.
36 7 Optional equipment OPTIONAL EQ UIPMENT SYSTEM CONFIGURA TION A number of options are av ailable f or the copier which allow y ou to configure a copier system to meet your particular needs.
37 7 Optional equipment SINGLE P ASS FEEDER (AR-SP3) The single pass f eeder (SPF) holds up to 30 originals f or automatic f eeding. Part names Document feeder tray Feeding roller cover Original guides SPF exit area Specifications Acceptable originals W eight: 14 to 23 lbs.
38 7 Optional equipment ● Bef ore f eeding or iginals in the document f eeder tra y , be sure to remov e any staples or paper clips from them. ● Bef ore placing curled or wavy originals into the document f eeding tray , be sure to flatten them. If not, or iginal misfeeds ma y result.
39 7 Optional equipment (B) Open the original cov er and rotate the roller rotating knob to remov e the misfed original from the e xit area. If the misf ed original cannot be easily remov ed, proceed to (C). (C) If the original does not mov e easily into the SPF exit area, remo ve it in the direction of the arrow while rotating the knob .
40 7 Optional equipment 250-SHEET P APER FEED UNIT (AR-DE9) The paper f eed unit pro vide the con v enience of increased paper capacity f or the copier and a greater choice of paper sizes readily a vailable f or cop ying.
41 7 Optional equipment Close the lower side co v er. Close the side cov er by pressing the round projections near the side co ver open b utton. The misfeed ( ) indicator will go out and the ready ( ) indicator will light up . Specifications Copy paper size 5-1/2" x 8-1/2" to 8-1/2" x 14" Paper weight 15 lbs.
INDEX 2 250-sheet paper f eed unit (AR-DE9) – loading cop y paper . . . . . . . . . . . . . . 40 – misf eed remov al . . . . . . . . . . . . . . . . 40 – par t names . . . . . . . . . . . . . . . . . . . . 40 – specifications . . . . . . . . .
P P aper – loading . . . . . . . . . . . . . . . . . . . . . . . . 10 – special . . . . . . . . . . . . . . . . . . . . . . . . 34 – specifications . . . . . . . . . . . . . . . . . . . 34 P aper f eed area . . . . . . . . . . . . . . . . . . . 27 P aper output tra y .
Date Issued:No v . 1, 2000 MA TERIAL SAFETY D A T A SHEET MSDS No . F-01001 Section 1. Product Identification Pr oduct: AR-152NT/T/FT/ST (Black T oner) Section 2. Supplier’ s Name and Address Shar p Cor por ation 22-22 Nagaike-cho , Abeno-ku, Osaka, Japan Local suppliers are listed below .
Section 6. Physical Chemical Characteristics Boiling / Melting P oint: Not applicab le Specific Gravity: 1.1 V apor Pressure: Not applicable Solubility in W ater: Negligible V apor Density: Not applicable PH: Not applicab le Evaporation Rate: Not applicab le Viscosity: Not applicable Appearance: Fine powder Color: Black Odor: Odor less Section 7.
Date Issued :No v . 1, 2000 MA TERIAL SAFETY D A T A SHEET MSDS No . F-31001 Section 1. Product Identification Pr oduct AR-152ND/D V/SD (Blac k Dev eloper) Section 2. Supplier’ s Name and Address Shar p Cor por ation 22-22 Nagaike-cho , Abeno-ku, Osaka, Japan Local suppliers are listed below .
Section 6. Physical Chemical Characteristics Boiling / Melting P oint: Not applicab le Specific Gravity: about 7.3 V apor Pressure: Not applicable Solubility in W ater: Negligible V apor Density: Not .
MEMO.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PRINTED IN CHINA 2000M KS TINSE0461QSZZ AR-151 SHARP ELECTR ONICS CORPORA TION Shar p Plaza, Mahwah, Ne w Jersey 07430-2135. www .shar p-usa.com SHARP CORPORA TION.
Een belangrijk punt na aankoop van elk apparaat Sharp AR-151 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sharp AR-151 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sharp AR-151 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sharp AR-151 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sharp AR-151 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sharp AR-151 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sharp AR-151 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sharp AR-151 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
