Gebruiksaanwijzing /service van het product AR-156 van de fabrikant Sharp
Ga naar pagina of 22
MODEL AR-156 • GETTING STARTED • MAKING COPIES • SPECIAL FUNCTIONS • SUPPLIES AND USER MAINTENANCE • COPIER TROUBLE? • APPENDIX • OPTIONAL EQUIPMENT 3 12 20 23 27 36 40 DIGITAL LASER COP.
3 1 Getting star ted GETTING ST AR TED This chapter provides basic inf or mation f or using the copier . INTR ODUCTION This copier has been designed to provide intuitiv e operating ease while requiring a minimum amount of space. T o get full use of all copier f eatures, be sure to f amiliarize yourself with this manual and the copier .
4 1 Getting star ted CA UTIONS F ollow the cautions belo w when using this copier . ● The fusing area is hot. Ex ercise care in this area when removing misf ed paper . ● Do not look directly at the light source. Doing so may damage y our eyes . ● Do not s witch the copier rapidly on and off .
5 1 Getting star ted MAIN FEA TURES High-speed laser copying ● Since warm-up time is zero , cop ying can be star ted immediately after the power s witch is tur ned on. ● First-copy time is only 9.6 seconds (normal mode). ● Cop ying speed is 15 copies/min.
7 1 Getting star ted OPERA TION P ANEL Original to copy key and indicator s : T wo-sided copies from one- sided originals. T urn on Long Edge or T urn on Shor t Edge can be selected. : T wo-sided copies from two- sided originals. (Can be selected only when the RSPF is used.
10 1 Getting star ted LO ADING COPY P APER Raise the handle of the paper tra y and pull the paper tra y out until it stops. Adjust the paper guides on the paper tra y to the copy paper width and length. Squeeze the le ver of paper guide and slide the guide to match with the width of the paper .
11 1 Getting star ted Gently push the paper tra y back into the copier . After loading cop y paper , to cancel the blinking “ P ” without restar ting copying, press the clear ( ) k ey . The “ P ” in the display will go out and the ready ( ) indicator will light up .
12 2 Making copies MAKING COPIES This chapter describes basic copying functions and some other cop ying functions using the b ypass tra y . NORMAL COPYING This copier has two document input stations -re v ersing single pass feeder (RSPF) f or automatic document f eeding and an original table f or manual handling of documents.
13 2 Making copies NORMAL COPYING T ur n the po wer s witch on. The ready ( ) indicator will light up . ● The copier will enter a pow er sav e mode once the set time has elapsed without any copier oper ation after the last cop y of a r un is made or po wer is turned on.
14 2 Making copies NORMAL COPYING Original face up B. When using the original table: (1) Open the original cov er . (2) Place an original face do wn on the or iginal tab le. Align it with the original scale and the centering ( ) mark. Close the or iginal co ver .
15 2 Making copies NORMAL COPYING D . When cop ying in the two-sided to one-sided mode: Use the original to copy k ey to select the two-sided to one-sided cop ying mode. The originals must hav e been set in the RSPF in step 3. Ensure that the desired paper tra y is selected.
16 2 Making copies When making two-sided copies from the original table , place the second original on the original table and press the print ( ) ke y .
17 2 Making copies Set the number of copies using the cop y quantity ( , ) ke ys and press the print ( ) k ey . REDUCTION/ENLARGEMENT/ZOOM Three preset reduction ratios and two enlargement ratios can be selected. The zoom function enables cop y ratio selection from 50% to 200% in 1% increments.
18 2 Making copies BYP ASS FEED (including special paper) The bypass tra y can automatically f eed up to 50 sheets of standard cop y paper and can also f eed special papers such as transparency film and labels one sheet at a time. Copy paper measuring from 3-1/2" x 5-1/2" to 8-1/2" x 14" and in the weight range of 14 to 34.
19 2 Making copies Print face Press the tra y select ( ) ke y to select the bypass tr a y . Set the number of copies if using standard cop y paper . Press the pr int ( ) k e y .
27 5 Copier trouble? COPIER TR OUBLE? This chapter describes misfeed removal and troubleshooting. MISFEED REMO V AL When the misfeed ( ) indicator b links or blinks in the displa y , the copier will stop because of a misfeed. If a misf eed occurs when using the RSPF , a number ma y appear in the displa y after a minus sign.
28 5 Copier trouble? MISFEED REMO V AL A Misfeed in the paper feed area Gently remov e the misf ed paper from the paper f eed area as shown in the illustration. When blinks in the display and the misfed paper is not seen from the paper feed area, pull out the paper tra y and remov e the misfed paper .
29 5 Copier trouble? MISFEED REMO V AL ● Do not touch the photoconductiv e drum (green por tion) when removing the misf ed paper . Doing so may damage the drum and cause smudges on copies. ● Do not remov e the misf ed paper from abov e the fusing unit.
30 5 Copier trouble? Rotate the f eeding roller in the direction of the arrow and gently remov e the misfe d paper from the e xit area. F eeding roller Raise the fusing unit release lev er , close the front cover and then close the side co ver b y pressing the round projections near the side cov er open button.
31 5 Copier trouble? MISFEED REMO V AL Roller rotating knob With the RSPF , pull out the re versing tra y to remov e the misfed original. With the RSPF , after removing the misf ed or iginal from the e xit area, be sure to inser t the re v ersing tra y into the e xit area until it locks in place .
32 5 Copier trouble? DEVELOPER REQUIRED When the indicator lights up , the de veloper should be replaced.DEVELOPER REPLA CEMENT SHOULD ONL Y BE DONE BY AN A UTHORIZED SHARP SER VICE TECHNICIAN. Contact University Copy Service at Ext. 3012 as soon as possib le.
35 5 Copier trouble? A UT OMA TIC EXPOSURE ADJUSTMENT The automatic exposure le vel can be adjusted to suit y our copying needs . This lev el is set f or cop ying from the or iginal tab le and copying from the RSPF respectiv ely .
Een belangrijk punt na aankoop van elk apparaat Sharp AR-156 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sharp AR-156 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sharp AR-156 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sharp AR-156 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sharp AR-156 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sharp AR-156 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sharp AR-156 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sharp AR-156 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
