Gebruiksaanwijzing /service van het product AR-M200 van de fabrikant Sharp
Ga naar pagina of 111
DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL (for general information) Page PREPARATIONS LOADING PAPER MAKING COPIES PRINTER/SCANNER FUNCTIONS USER SETTINGS TROUBLESHOOTING AND MAINTENANCE OPTIONAL.
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. Do not make copies of anything which is prohibited from copying b y law . The follo wing items are normally prohibited from copying by nati onal law .
1 CA UTIONS ....... .............. ............. .............. .............. ............ ............. .............. ........... 3 ENVIRONMENT AL INFORMA TION ............... .............. .............. ............. .............. .... 5 INTRODUCTIO N .
2 6 PRINTER/SCANNER FUNCTIONS USING THE PRINTER MODE ............. ........... .............. .............. .............. ...... 50 BASIC PROCEDURE FOR PRINTI NG ................ .............. ............. .............. .. 50 USING THE SCANNER MODE.
3 CA UTIONS Caution label on the machine The label ( ) in the fusing area of the machine indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using the machine Follow the cautions below when using this machine. Warning: • The fusing area is hot.
4 Cautions on handling th e machine Be careful in handling the machine as follows to maintain the performance of this machine. Do not drop the machine, subje ct it to shock or st rike it against any object. Store spare toner cartridges in a c ool dry place without removing from the package before use.
5 ENVIRONMENT AL INFORMA TION Laser information SOFTW AR E LICENSE The SOFTWARE LICENSE will appear when you install th e software from the CD-ROM. By using all or any portion of the software on the CD -ROM or in the machine, you are agreeing to be bound by the terms of the SOFTWARE LICENSE.
6 INTRODUCTION Using the manual This machine has been desi gned to provide convenien t copying features i n a minimum amount of office s pace and with maximum operational ease. To get full use of all machine features, be sure t o familiarize yo urself with thi s manual and the machine.
7 Explanation of illustration Depend ing on the mod el you have a nd on the optio ns installed, s ome of the illust rations in this manual may be different , however, t he basic o perations are the same. MAIN FEA TURES High-speed laser copy ing First-copy time* 1 is only 8.
8 Enhanced copying features • Zoom copies can be made from 25% to 400% in increments of 1%. (When the RSPF is being used, the zoom cop y ratio range is 50% to 200%.) • Continuous copying of up to 99 copies is possible. • Sets of output can be offset from each other for easy separation (offset function).
9 1 Chapter 1 1 This chapter provides basic information t hat you should know before using the machine. PA R T N A M E S Document glass Paper output tra y extension Operation panel Po wer switch Front.
PREP ARA TIONS 10 Operation panel [MODE SELECT] key / Mode indicators Press this key to select the mode. The indicator of the selected mode lights (copy, printer, scanner, fax mode indi cators). Display This shows messages indicating the machine status and any problems that occur, as well as user programs and function setting menus.
PREP ARA TIONS 11 1 [ZOOM] key Press to select an enlargement or reduction ratio. To select a preset ratio setting, press the [ZOOM] key and select the desired preset ratio.
12 CONNECTING THE PO WER CORD 1 Ensure that the power switch of the unit is in the OFF position. Insert the attached power cord into the power cord socket at the rear of the unit. 2 Plug the other end of the power c ord into the nearest outlet. PO WER ON AND OFF The power switch is located on the left side of the machine.
PREP ARA TIONS 13 1 Power off Make sure that the machine is not in operation and t hen turn the power switch to the "OFF" position. If the power switch is turned off while the machine is in operation, a misfeed may occur and the job that was in progress will be cancelled.
14 2 Chapter 2 The tray location indicator will blink when there is no paper in the selected paper tray, or when the selecte d paper tray is not closed or is improperly closed. PA P E R For best results, use only SHARP recommended paper. * 1 The number of sheets of paper that can be loaded varies dependi ng on the weight of the paper.
LO ADING P APER 15 2 Special papers Follow these guidelines when using special papers. ● Use SHARP recommended transparency film and label shee ts. Using other than SHARP recommended paper may result in misfeeds or smudges on the output.
LO ADING P APER 16 3 Gently push the paper tr ay back into the machine. • If you loaded a diff erent size of paper than w as loaded previously in the tra y , go to "CHA NGING A TRA Y'S P APER SIZE SETTING" (p.
17 2 BYP ASS FEED (including special paper) The bypass tray can be used to feed st andard pa per, transparency film, labels, envelopes, and other special purpose paper. Important points when inserting paper in the bypass tray Up to 50 sheets of standard copy paper can be inserted in the bypass tr ay.
LO ADING P APER 18 Loading paper in the bypass tray 1 Open the bypass tray and extend the tray. 2 Set the bypass tray paper guide s to the paper width. Insert the paper (print face down) all the way into the bypass tray. 3 Press the [TRAY SELECT] key ( ) to select the bypass tray.
19 2 CHANGING A TRA Y'S P APER SIZE SETTING Follow these steps to change a tray's paper size setting. 1 Press the [MENU] key. Press the [ ] key ( ) or [ ] key ( ) until "PAPER SIZE" appears, and then press the [OK] key. 2 Press the [ ] key ( ) or [ ] key ( ) to select the tray, and th en press the [OK] key.
20 3 Chapter 3 This chapter explains basic cop ying functions. NORMAL COPYING Using the document glass 1 Open the document cover/RSPF, and place the ori ginal face down on the document glass. [How to place the original] Align the original with th e original scale and the centri ng ( ) mark.
MAKING COPIES 21 3 Removing the document cover To copy large originals like newspapers, remove the document cover. To remove the cover, lift straight up as shown. To replace the cover, do the reverse. The RSPF cannot be removed. Using the RSPF 1 Make sure that an original ha s not been left on the document glass.
MAKING COPIES 22 Originals that cannot be used in the RSPF The following originals cannot be used. These may cause m isfeeds or smudging and unclear images. • T ransparencies, tracing paper , othe r transparent or translucent paper , and photographs.
MAKING COPIES 23 3 Setting the number of cop ies Press the numeric keys to set the number of copies. The set number of copies appears in t he display. A max imum of 99 copies can be set. If you wish to make only a single copy, copying is possible with the display showing "0".
24 MAKING A COPY D ARKER OR LIGHTER Automatic exposure adjustment is initially enabled . This function automatically adjusts the copy image according to the orig inal being copied. If you wish to select the exposure level yours elf, follow the steps below.
25 3 REDUCTION/ENLARGEM ENT/ZOOM Copies can be reduced down to 25% or enlarged up to 400%. (When the RSPF is being used, the zoom copy ratio range is 50% to 200%.) The [ZOOM] key can be pressed to quickly select a ratio from among eight pr eset ratios.
26 4 Chapter 4 A UT OMA TIC TWO-SIDED COPYING Two originals can be automatically co pied on to both sides of a single sheet of paper. When the RSPF is used, two-sided copies of two-sided originals can easily be made.
CONVENIENT COPY FUNCTIONS 27 4 Using the document glass 1 Place the original that you wish to copy onto the front side of the paper on the document glass and close the document cover/RSPF. 2 Press the [2-SIDED COPY ( )] key until "1 TO 2" appears, and then press the [OK] key.
CONVENIENT COPY FUNCTIONS 28 Using the RSPF 1 Place the original(s) in the RSPF. (p.21) If you place an odd number of originals for one-sided to tw o-sided copying, the last page will be one-sided. 2 Press the [2-SIDED COPY ( )] key* 1 and select the two-sided copy mode that you wish to use.
29 4 SORT COPY Copies of multiple original pages can be sorted into sets. Using the document glass 1 Place the first original. (p. 20) 2 Press the [E-SORT/SP.FUNC ( )] key until "SORT" appears and then press the [OK] key. 3 Press the [ ] key ( ) to move " " to the "ON" position and then press the [OK] key.
CONVENIENT COPY FUNCTIONS 30 Using the RSPF 1 Place the originals. (p.21) 2 Press the [E-SORT/SP.FUNC ( )] key until "SORT" appears and then press the [OK] key. 3 Press the [ ] key ( ) to move " " to the "ON" position and then the [OK] key.
31 4 COPYING MUL TIPLE ORIG INA LS ONT O A SINGLE SHEET OF P APER (2 IN 1 copy) Multiple originals can be copied onto a single sheet of paper in a selected layout pattern. This function is convenient for c ompiling multi-page reference mater ials into a compact format, or for providing an overvi ew of all pages of a document on a single page.
CONVENIENT COPY FUNCTIONS 32 4 Press the [ ] key ( ) or [ ] key ( ) to select the original size and t hen press the [OK] key. The following original sizes can be selected: "A4", "B5", "A5", "8.5x14", "8.5x13", "8.
CONVENIENT COPY FUNCTIONS 33 4 Using the /RSPF 1 Place the originals. (p.21) 2 Press the [E-SORT/SP.FUNC ( )] key until "2IN1" appear s and then press the [OK] key. 3 Press the [ ] key ( ) to move " " to the "ON" position and then press the [OK] key.
34 CREA TING MARGINS WHEN COPYING (Margin shift) The margin shift function is used to automatic ally shift the text or image or the copy paper approximately 10 mm. As shown below, LONG EDGE or SHORT EDGE can be selected. 1 Place the original(s). 2 Press the [E-SORT/SP.
CONVENIENT COPY FUNCTIONS 35 4 3 Press the [ ] key ( ) to move " " to the "ON" position and then press the [OK] key. 4 Press the [ ] key ( ) or [ ] key ( ) to select the margin position and then press the [OK] key. Select "LONG EDGE" or "SHORT EDGE".
36 5 Chapter 5 This chapter explains how to install and conf igure the software that is required for the printer and scanner functions of the machine. The procedure for viewing the Online Manual is also explained.
37 5 BEFORE INST ALLA TION Hardware and software requirements Check the following hardware and s oftware requirements in o rder to install the software. * 1 Compatible with Windows 9 8, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Editi on preinstalled model standardly equipped with a USB port.
38 INST ALLING THE SOFTW ARE Using the machine with a USB connection 1 The USB cable must not be connected to the machine. Mak e sure that the cable is not connected before proce eding. If the cable is connected, a Plug and Play window will appear. If this happens, click the "Cancel" button to cl ose the window and discon nect the cable.
INST ALLING THE SOFTW ARE 39 5 7 To install all of the software, click the "Standard" button and go to step 12 . To install particular packages, click the "Custom" button and go to next step. 8 Click the "MFP Driver" button.
INST ALLING THE SOFTW ARE 40 10 You will return to the window of step 8. If you wish to install Button Manager or Sharpdesk, click the "Utility Software" button. If you do not wish to insta ll the Utilit y Software, click the "Close" button and go to step 12.
INST ALLING THE SOFTW ARE 41 5 12 When installing is finished, click the "Close" button. A message will appear instr ucting you to connect the machine to your computer. Click the "OK" button. 13 Make sure that the power of the machine is turned on, and then connect the USB cable (p.
INST ALLING THE SOFTW ARE 42 Connecting a USB cabl e Follow the procedure below to connect the machine to your computer. A USB cable for connecting the machine to your computer is not included with the machine. Please purchase the appropriate cable for your computer.
INST ALLING THE SOFTW ARE 43 5 Using the machine as a sha red printer If the machine will be used as a shared pr inter on a network, follow these steps to install the printer driver in the client computer. 1 Perform steps 2 through 6 in "INSTALLING THE SOFTWARE" (p.
INST ALLING THE SOFTW ARE 44 5 Click the "Add Network Port" button. In Windows Vista, the "Add Network Port" button does not appear . 6 Select the network printer that is shared and click the "OK" button. Ask your network administrator for the server name and printer name of the machine on the network.
INST ALLING THE SOFTW ARE 45 5 SETTING UP BUTT ON MANA GER Button Manager is a software program that works with the scanner driver to enable scanning from the machine. To scan using the machine, Button Manager must be linked with the scan menu on the machine.
INST ALLING THE SOFTW ARE 46 5 Select "Start this program" and then select "Sharp Button Manager T" from the pull-down menu. 6 Click the "Apply" button . 7 Repeat Steps 4 through 6 to link Button Manager to "SC 2:" through " SC6:".
INST ALLING THE SOFTW ARE 47 5 Windows 98/Me/2000 1 Click the "Start" button, select "Settings", and then click "Control Panel". 2 Double-click the "Scanners and Cameras" icon. 3 Select "SHARP AR-XXXX" and c lick the "Properties" button.
INST ALLING THE SOFTW ARE 48 6 Select "Sharp Button Manager T" in "Send to this application". 7 Click the "Apply" button . 8 Repeat Steps 5 through 7 to link Button Manager to "SC 2:" through " SC6:". Select "SC2:" from the "Scanner events" pull-down menu.
49 6 Chapter 6 6 The machine includes a USB connector as standard equipment. The machine has the following features: • High-speed data transfer (when connected to a USB 2.0 connector) • ROPM* function * ROPM is an acronym for "Rip Once Print Many" processing.
50 USING THE PRINTER MODE The procedure for loading paper for printing is the same as for loading copy paper. See "LOADING PAPER" (p.14). B ASIC PR OCEDURE FOR PRINTING The basic procedure for printing is expl ained in the following. To use convenient printer functions, see the "Online Manual " or the printer driver help file.
51 6 USING THE SC ANNER MODE The procedure for placing the original is the same as for copying. See "NORMAL COPYING" (p.20). SCANNING USING TH E KEYS ON THE MA CHINE When scanning is perform.
PRINTER/SCAN NER FUNCTIONS 52 Button Manag er scan menu For information on Button Manager setti ngs, see the Button Manager help file. The names in the Button Manager menu ("xxxx" in "SC1:xxxx", etc.) can be changed. See the online manual.
53 6 HO W T O USE THE ONLINE MANU AL The online manual provides detailed instruct ions for operating the unit as a printer and scanner. It also provides methods for de aling with printing or scanner problems. 1 Turn on your comput er. 2 Insert the supplied CD-ROM into your CD-ROM drive.
54 7 Chapter 7 The user settings allow you to custo mize machine settings to better meet your needs. USER PROGRAMS The user settings consist of the following items. To change the user program settings as explained in "SELECTING A SETTING FOR A USER PROGRAM" (p.
USER SETTINGS 55 7 4 A UT O SHUT -OFF TIME 1: 5 MIN. 2: 30 MIN. 3: 60 MIN. 4: 120 MIN. 5: 240 MIN. • This function automatically switches the machine to a state that consumes ev en less power than preheat mode if the set duration of time elapses without the machine being used when the power is on.
USER SETTINGS 56 13 MEM. FOR PRINTER 1: 30% 2: 40% 3: 50% 4: 60% 5: 70% • Use this to change the propor tion of machine memor y used f or printer mode. 14 A UT O KEY REPEA T 1: ON 2: OFF • Use this setting to select whether or not holding down a key causes r epeated input of the ke y .
USER SETTINGS 57 7 20 LANGU AGE 1: AMERICAN ENGLISH 2: ENGLISH 3: FRENCH 4: SP ANISH 5: GERMA N 6: IT AL IAN 7: DUTC H 8: SWEDISH 9: NOR WEGIA N 10: FINNISH 11: D ANI SH 12: HUNGARIAN 13: CZE CH 14: PO LISH 15: R USSIAN 16: SLO V AK 17: PORTUGUESE • T his is used to set the language used in the display .
USER SETTINGS 58 Print mode * 1 The scanning speed increases when the USB 2.0 mode is set to "HI-SPEED", however, the printing speed doe s not increase considerably.
59 7 SELECTING A SETTING FOR A USER P ROGRAM 1 Press the [MENU] key and then press the [OK] key. In printer mode, the user program s are accessed by simply pressing the [MENU] key. 2 Press the [ ] key ( ) or [ ] key ( ) to select the item that you wish t o configure in the USER PROGRAM items, and then press the [OK] key.
USER SETTINGS 60 Audible signals (key entry beep, in valid key beep, base setting beep) The machine sounds three different type s of beep signals: a key entr y beep that sounds when a valid key is pre.
61 8 Chapter 8 8 When the account control function is enabled, you can control use of the machine by account or view the total c opied pages by each account. There are some progra m menus for this function as in the table shown. PREP ARING FOR USING ACCOUN T CONTROL SETTINGS Entering account control mode 1 Press the [MENU] key.
A CCOUNT CONTROL SETTINGS 62 Enabling auditing mode 4 Press the [ ] key ( ) or [ ] key ( ) to select "2: ACC. CONTROL SET" and then press the [OK] key. 5 5 Press the [ ] key ( ) or [ ] key ( ) to select "1: AUDITING MODE" and then press the [OK] key.
63 8 A CCOUNT NUMBER CONTR OL This program is used to enter, delete and change account numbers. 1 After step 1, 2 and 4 on page 61 - 62, press the [ ] key ( ) or [ ] key ( ) until [4: ACC. # CONTROL] appears and t hen press the [OK] key. 2 3 4 5 Entering an account number 1 Select "1.
A CCOUNT CONTROL SETTINGS 64 3 If you wish to delete an each account number, select "2. DELETE ONE ACCOUNT" and then press the [OK] key. 4 Enter the account n umber that you wish to dele te with the numeric keys and then press the [ OK] key.
65 8 T O T AL PER ACCOUNT This program is used to display the page counts of each account. 1 After step 1, 2 and 4 on page 61 - 62, press the [ ] key ( ) or [ ] key ( ) until "2: TOTAL PER ACCOUNT" appears, and then press the [OK] key. 2 This program is used to display the page counts of each account.
66 COPYING WHEN A UDITING MODE IS ENABLED When account control is enabled, the account numbe r entry screen appears . 1 Enter your five-digit account num ber with the numeric keys. 2 When a valid account number is entered, the number of copies already made by that account appears for several seconds on the initial screen.
67 9 Chapter 9 9 Problems related to general use of the machine, the copy function, and software setup are explained here. Be sure to chec k the problem carefully before calling for service, as many p roblems can be solved by the us er.
TROUBLESHOO TING AND MAINTENANCE 68 Error indicator Blinks INST ALL A NEW T ONER CAR TRIDGE The toner car tridge is not installed correctly . R einstall the toner car tridge. 80 Steadily lit T ONER CAR TRIDGE IS NEAR EMPTY . Replacement of toner car tridge will be needed soon.
69 9 TROUBLESHOO TING THE MA CHINE The following problems are related to the general operation of the machine and copying. Problem Cause and solution Pag e The machine does not operate. The machine is not plugged into a power outlet. → Plug the machin e into a grounded outlet.
TROUBLESHOO TING AND MAINTENANCE 70 Problem Cause and solution Pag e Part of the image is cut off or there is too much blank space. The original was not placed in the correct position. → Place the original correctly . 20, 21 An appropriate ratio was not used f or the size of the original and the size of the paper .
TROUBLESHOO TING AND MAINTENANCE 71 9 Paper misfeed. Misfeed occur . → T o remove the misf eed, see "MISFEED REMO V AL". 76 The paper is outside of the specified size and weight range. → Use copy paper within the specified range. 14 Paper curled or damp.
TROUBLESHOO TING AND MAINTENANCE 72 Paper size for a paper tray cannot be set. Copying or printi ng is performed. → Set the paper size after cop ying or printing is complete. - The machine has stopped temporarily due to running out of paper or a misfeed.
73 9 PROBLEMS DURING SETUP OF THE SOFTW ARE If the software does not install correctly, check the following ite ms on your computer. To remove the software, se e "Removing the software" (p.
TROUBLESHOO TING AND MAINTENANCE 74 Plug and play screen does not appear If the Plug and Play screen does not appear after you connect the machine to y our computer with a USB cable and turn on the ma chine, follow the st eps below to verify that the USB port is available.
TROUBLESHOO TING AND MAINTENANCE 75 9 The MFP driver cannot be correctly installed by Plug and Play (Windows 2000/XP/Vista) In Windows 2000/XP/Vista, if the M FP driv er cannot be correctly installed .
76 MISFEED REMO V AL When a misfeed occurs, the error indica tor blinks, "CLEAR PAPER JAM" appears in the display, and the machin e stops operat ing. If a misfeed occurs when using the RSPF, "RETURN X ORIGINAL( S) START TO RESUME" will appear in the display.
TROUBLESHOO TING AND MAINTENANCE 77 9 A: Misfeed in the paper feed area 1 Gently remove the misf ed paper from the pape r feed area as shown in the illustration. If the error indicator blinks and the misfed paper is not visible in the paper feed area, pull out the paper tray and remove the misfed paper.
TROUBLESHOO TING AND MAINTENANCE 78 2 Gently remove the misfed paper from under the fusing unit as shown in the illustration. If the paper cannot be removed , proceed to " C: Misfeed in the transport area".
TROUBLESHOO TING AND MAINTENANCE 79 9 4 Raise the fusing unit re lease l ever, close the front cover and then close the side cover by pressing the round projections near the side cover open button. The error ind icator will go out and the ready indicator will light up.
80 T ONER CAR TRIDG E REPLA CEMEN T When toner is low, the error indicato r will light up and "TONER CARTRIDGE IS NEAR EMPTY." will appear in the display to alert you to purchase a new tone r cartridge.
TROUBLESHOO TING AND MAINTENANCE 81 9 3 Gently pull the toner cartridge out while pressing the lock release lever. 4 Remove the toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally four or fiv e times. After shaking the cartridge, remove the toner seal.
TROUBLESHOO TING AND MAINTENANCE 82 6 Close the front cover and then the side cover by pressing the round projections near the side cover open button. The error indicator will go out and the ready indicator will light up. 7 SCAN HEAD LOCKING SWITC H The scan head locking switch is under the original table.
83 9 CHECKING THE T OT AL COUNT You can check the total number of pages output by the machine (all pages printed by the copy function and printer function), as well as the output c ounts of each function (number of copies, number of s canned pages, number of faxes, etc.
84 CLEANING THE MA CHINE Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to clean the machine on a regular basis. Cabinet Wipe the cabinet with a soft, clean cloth. Document glass and the ba ck side of the RSPF Stains on the glass, RSPF scanning window, cover or RSPF roller will also be copied.
85 9 TRANSFER CHARG ER 1 Turn the power switch off. ( p.13 ) 2 Ensure that the by pass tray is open and th en open the side cover while pressing the side cover open butt on.
86 10 Chapter 10 SYSTEM CONFIGURA TION A number of options are available for the uni t which allows you to configure a system to meet your particular needs. The options include the following. F A CSIMILE EXP ANS ION KIT (AR-FX13) This allows the machine to be u sed as a facsimile machine.
87 10 250-SHEET P APER FEED UNIT (AR-D33) The paper feed unit provide the convenience of increase d paper capacity for the unit and a greater choice of paper size readily available for copyin g.
OPTIONAL EQUIPMENT 88 Using the AR-D33 with the printer function To use the AR-D33 with the printer function, follow these steps to adjust the s ettings in the printer driver. 1 Click the "start" button. 2 Click "Control Panel", select "Pri nter and Other H ardware", and then click "Printer and Faxes".
89 11 Chapter 11 SPECIFICA TIONS Model AR-M200 AR-M201 Ty p e Digital Multifunctional System, Desktop Photoconductive type OPC drum Document glass type Fixed Copy/printi ng system Dr y , electrostatic transfer Originals Sheets, bound documents Originals size Max.
APPENDIX 90 * 1 When making multiple duplex copies, the copy sp eed will vary based on the environment conditions. * 2 The firs t-copy time is me asured afte r the power sav e indicator turn s off fol.
APPENDIX 91 Printer Function * When printing same docume nt continuously on A4 plain paper in non-offs et mode, excluding processing time. Print speed* 20 ppm Resolution 600 dpi Memory Approx. 30MB Emulation SPLC (Sharp Printer Language with Compression) Interface USB 2.
APPENDIX 92 Scanner Function Network Expansion kit (AR-NB2A ) * Available only if the PS3 expans ion kit (AR-P K1N) is insta lled. Ty p e Flatbed scanner Scanning method Document glass/RSPF Light sour.
APPENDIX 93 Reversing Single Pass Fe eder (AR-RP9) 250-sheet paper feed unit (AR-D33) Facsimile expansion kit (AR-FX13 ) For the specifications of expansion kit AR -FX13, please refer to the AR-FX13 f ax operation manual itself.
94 INDEX Symbols [ ] key............. ............. 10, 27, 29, 32 [ ] key ............. .............. ........... ..... 10 [ ] key ............. .............. ........... ..... 10 2 2 IN 1 copy ................ .............. ......... 31 250-sheet paper feed unit .
95 I Initial settings............... .............. ....... 12 Installing the software................ ....... 36 Interface cable .................. .............. .. 88 Introduction ......... .................. .......... .... 6 L Language setting ..
96 R Ready indicator ......... ........... 11, 12, 76 Reduction/enlargement /zoom .... ...... 25 Removing the software ......... ............ 75 Roller rotating knob .............. ............ 78 RSPF ............. ............ .............. .......
97 INDEX BY PURP OSE Preparations Paper, loading - Bypass tray............. .............. ........ 17 - Paper tray ...... .................. .......... ... 15 Power, turn off .................. .............. ... 13 Power, turn on .................. .
MATERIAL SAFETY DATA SHEET Page : 1/4 Date Issued : Nov. 1, 2007 MSDS No. F-01601 1.PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-208NT/ AR-208T (Black Toner) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below.
MATERIAL SAFETY DATA SHEET Page : 2/4 Date Issued : Nov. 1, 2007 MSDS No. F-01601 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from e xposure based on animal tests performed using toner.
MATERIAL SAFETY DATA SHEET Page : 3/4 Date Issued : Nov. 1, 2007 MSDS No. F-01601 8.EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Measures Ventilation : Not required under intended use.
MATERIAL SAFETY DATA SHEET Page : 4/4 Date Issued : Nov. 1, 2007 MSDS No. F-01601 Chronic Effect : In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lu.
MATERIAL SAFETY DATA SHEET Page : 1/4 Date Issued : Nov.01, 2007 MSDS No. F-31601 1.PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-208ND / AR-208DV (Black Developer) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below.
MATERIAL SAFETY DATA SHEET Page : 2/4 Date Issued : Nov.01, 2007 MSDS No. F-31601 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from e xposure based on animal tests performed using toner.
MATERIAL SAFETY DATA SHEET Page : 3/4 Date Issued : Nov.01, 2007 MSDS No. F-31601 8.EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Measures Ventilation : Not required under intended use.
MATERIAL SAFETY DATA SHEET Page : 4/4 Date Issued : Nov.01, 2007 MSDS No. F-31601 Chronic Effect : In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lu.
Attention: Your product is marked with this sy mbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products. A. Information on Disposal for Users (private households) 1.
Required in IEC-950 (EN 60 950) - Europe • The equipment should be installed near an accessible socket outlet for easy disconnection. Required in Appendix ZB of BS 7002 (En 60 950) — United Kingdo.
CAUTION VORSICHT ADVARSEL ADVERSEL VARNING VARO! CLASS 3B INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. UNSICHTBARE LASERSTRAHLUNG DER KLASSE 3B, WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERERÜCKT.
AR-M200 / AR-M201_v1 AR-M200 / AR-M201 OPERATION MANUAL SHARP MANUF A CTURING FRANCE S.A. Route de Bollwiller - SOUL TZ 68503 GUEBWILLER CEDEX FRANCE.
Een belangrijk punt na aankoop van elk apparaat Sharp AR-M200 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sharp AR-M200 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sharp AR-M200 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sharp AR-M200 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sharp AR-M200 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sharp AR-M200 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sharp AR-M200 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sharp AR-M200 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
