Gebruiksaanwijzing /service van het product PN-V601 van de fabrikant Sharp
Ga naar pagina of 42
PN-V601 LCD MONIT OR OPERA TION GUIDE.
2 E This guide contains instructions regarding operation, settings, and similar details. For instructions regarding connection and installation, refer to the included Operation Manual. Manual Scope - Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.
3 E n Front view 1 23 45 6 7 8 9 The rear buttons if seen from the front 1. LCD panel 2. INPUT button 3. MENU button 4. VOL -/Cursor control ( ) button 5. VOL +/Cursor control ( ) button 6. BRIGHT -/Cursor control ( ) button 7. BRIGHT +/Cursor control ( ) button 8.
E 4 Part Names n Remote control unit (Supplied with the PN-ZR01 (optional)) 1 2 3 4 5 6 7 12 9 10 11 8 1. Signal transmitter 2. POWER button 3. MUTE button 4. VOL +/Cursor control ( ) button 5. BRIGHT -/Cursor control ( ) button 6. DISPLA Y button 7.
5 E Basic Operation When performing operation of multiple monitors with the remote control unit, rst set the remote control unit to the appropriate remote control mode (see page 7). 1 2 3 4 5 6 7 8 TIPS • Y ou can perform operation of the monitor with the rear buttons.
E 6 Basic Operation n Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it lls the entire screen. A V input An image with a 4:3 aspect ratio is stretched to ll the entire screen.
7 E Remote Control Mode With the remote control unit it’s possible to perform operation of... • The primary monitor • Monitors with a specied ID No. • All primary/secondary monitors It’s necessary to specify which type of operation will be performed in advance.
8 E Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 9 to 12 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed.
E 9 Menu item details The menu will differ depending on the input mode. n SCREEN AUTO (PC D-SUB/PC RGB) The CLOCK, PHASE, H-POS, and V -POS are automatically adjusted.
E 10 n AUDIO TREBLE Adjusts the volume of treble-level sound. BASS Adjusts the volume of bass-level sound. BALANCE Adjusts the balance of the audio sound between right and left. RESET Resets the values of the AUDIO menu items to the factory preset values.
E 11 Menu Items AUDIO LEVEL(STEREO MINI) Selects the maximum audio input level of the audio input terminal. SELF ADJUST On a PC D-SUB/PC RGB screen, specify whether to perform screen adjustment automatically or not.
E 12 Menu Items n MUL TI ENLARGE (See page 13.) Sets whether or not to use the enlarge function. ADV ANCED (ENLARGE) ENLARGE H / ENLARGE V ......... Sets the number of screen splits (number of monitors) in the horizontal/vertical direction used for the enlargement.
E 13 Menu Items n Enlarge • Y ou can align several monitors and integrate them into a single large screen to display . • Up to ve monitors can be aligned in both the horizontal and vertical directions. • Each monitor displays enlarg ed views of separated images.
E 14 n SCHEDULE Y ou can set the time to switch the monitor on and off. Set th is funct ion with “SCHEDU LE” in t he OPTIO N menu. (See page 1 1.) SCHEDULE No. POWER DA Y OF THE WEEK TIME INPU T XXXX/XX/XX XXX XX:XX:XX (2) OK … [MENU] 1366x768 V: 60 Hz H: 47.
E 15 n ADV ANCED items (A V input) (See page 9 for additional Menu item details.) FLESH TONE Adjust the hue control. 3D-NR Reduce the noise of playback images on video. Setting a higher level reduces more noise. However , it may cause blurring on an image.
16 E Y ou can return the settings to their factory-preset values and restrict operations. 1. If using the remote control unit, press SIZE until “F” is displayed in the upper left area of the screen, then while “F” is being displayed, press , , , and in that order .
17 E Controlling the Monitor with a PC (RS-232C) Y ou can control this monitor from a PC via RS-232C (COM port) on the PC. Y ou can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 18), you can make input mode selection/adjustment or can check the status of a specic monitor .
E 18 Controlling the Monitor with a PC (RS-232C) n Response code format When a command has been executed correctly O K Return code (0D H , 0A H ) A response is returned after a command is executed.
E 19 Controlling the Monitor with a PC (RS-232C) n Commands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ......... A monitor receiving this command sets its own ID number in the parameter eld.
E 20 Controlling the Monitor with a PC (RS-232C) n Repeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. Y ou can use Repeater control function without assigning ID numbers.
E 21 RS-232C command table How to read the command table Command: Command eld (See page 17.) Direction: W When the “Parameter” is set in the parameter eld (see page 17), the command functions as described under “Control/Response Contents”.
E 22 PICTURE menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) AUTO AGIN W 1 When the input mode is PC D-SUB, PC RGB. - ○ ○ CONTRAST CONT WR 0-60 0-60 0-127 on PC D-SUB, PC RGB. ○ BLACK LEVEL BL VL WR 0-60 0-60 0-127 on PC D-SUB, PC RGB.
E 23 SETUP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) OSD H-POSITION OSDH WR 0-100 0-100 ○ ○ ○ OSD V -POSITION OSDV WR 0-100 0-100 MONITOR STDR WR 0-.
E 24 OPTION menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) DA TE/TIME SETTING DA TE WR AABBCCDDEE AABBCCDDEE AA: Y ear, BB: Month, CC: Day , DD: Time, EE: Minu.
E 25 Controlling the Monitor with a PC (RS-232C) MUL TI menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) ENLARGE ENLG WR 0-1 0-1 0: OFF , 1: ON - ○ ○ ENLARGE.
E 26 PIP/PbyP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) PIP MODES MWIN WR 0-3 0-3 0: OFF , 1: PIP , 2: PbyP , 3: PbyP2 ○ ○ ○ PIP SIZE MPSZ WR 1-12 1.
E 27 Others Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) SCREEN SIZE (PC) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 ○ ○ ○ SCREEN.
28 E When the PN-ZB02 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. Y ou can also congure the monitor to send e-mail notication when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).
29 E 29 ■T osetfromaPC When the monitor is connected to a PC, LAN settings can be congured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address.
30 E 30 5. Click on “LAN SETUP” under NETWORK. 6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”. T o set the address manually , set this to “OFF”.
31 E 31 ■INFORMA TION Information about this monitor appears. ■CONTROL Y ou can control the operations corresponding to the buttons ( POWER INPUT SIZE ) on the remote control unit. (See page 5.) TIPS • In standby mode, Power ON is the operation available.
32 E 32 ■NETWORK(LANSETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”.
33 E 33 ■NETWORK(GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network.
34 E 34 ■MAIL(RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error . RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notication e-mail to. CONDITION Specify the conditions to send mails.
35 E 35 Controlling the Monitor with a PC (LAN) ■SNMP Y ou can congure settings related to SNMP . SNMP SETTING Set whether to enable or disable SNMP . VERSION Set the version of the SNMP to be supported. COMMUNITY NAME 1 to 3 Set the name of the community required for the access.
36 E T roubleshooting If you are experiencing any problem with your display , before calling for service, please review the following troubleshooting tips.
37 E Specications n PN-V601ProductSpecications Model PN-V601 LCD component 60" Class [60 inch (152.4cm) diagonal] TFT LCD Max. resolution (pixels) 1366 x 768 Max.
38 E Specications n Dimensional Drawings Note that the values shown are approximate values. Unit: inch [mm] 52-5/8 [1335.9] Opening width (52-5/16 [1329.4]) Opening height (29-7/16 [747.7]) 29-1 1/16 [754.2] 7-7/8 [200] 5-7/8 [149.3] 52-5/8 [1335.9] 3-5/8 [92.
39 E n Compatible signal timing (PC) VESA Wide US TEXT Sun Screen resolution Hsync Vsyn c D ot frequency Digital 640 × 480 800 × 600 848 × 480 1024 × 768 1 152 × 864 *1 1280 × 768 1280 × 800 *1.
40 E n Compatible signal timing (A V) Screen resolution Frequency DVI-D* 2 HDMI Component* 2 1920 × 1080p * 1 24Hz - Ye s - 50Hz Ye s Ye s Ye s 59.94Hz Ye s Ye s Ye s 60Hz Ye s Ye s Ye s 1920 × 1080i * 1 50Hz Ye s Ye s Ye s 59.94Hz Ye s Ye s Ye s 60Hz Ye s Ye s Ye s 1280 × 720p 50Hz Ye s Ye s Ye s 59.
41 E Specications n PC/A V DVI-D input terminal pins (DVI-D 24 pin) No. Function No. Function 1 TMDS data 2- 13 N.C. 2 TMDS data 2+ 14 +5V 3 TMDS data 2/4 shield 15 GND 4 N.C. 16 Hot-plug detection 5 N.C. 17 TMDS data 0- 6 DDC clock 18 TMDS data 0+ 7 DDC data 19 TMDS data 0/5 shield 8 N.
PN-V601 Ge EN10H(1).
Een belangrijk punt na aankoop van elk apparaat Sharp PN-V601 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sharp PN-V601 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sharp PN-V601 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sharp PN-V601 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sharp PN-V601 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sharp PN-V601 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sharp PN-V601 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sharp PN-V601 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
