Gebruiksaanwijzing /service van het product 72362-93115 van de fabrikant Shindaiwa
Ga naar pagina of 20
Always wear eye protection when operat- ing this unit. WARNING! SHINDAIW A OWNER'S/ OPERA TOR'S MANUAL 357 CHAIN SA W 3 5 7 0 1 WARNING! Minimize the risk of injury to yourself and others; read this manual and familiarize yourself with its contents! Part Number 72362-93115 Rev.
2 39 NOTES.
3 Introduction The Shindaiwa 357 Top-Handle saw has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety, or durability.
4 Read and follow the Operator’s Manual. Failure to do so could result in serious injury. Wear eye and hearing protection at all times during the operation of this unit. Do not operate this tool if you are tired, ill or under the influence of alcohol, drugs, or medication.
5 35702 Clutch Cover Muffler Outlet IMPORTANT! The operational procedures de- scribed in this manual are intended to help you get the most from your machine and also to protect you and others from harm. These procedures are general guidelines only, and are not intended to replace any safety rules/laws that may be in force in your area.
6 DESCRIPTION Model ....................................................................................................................... 35 7 Engine Type ................................................................ 2 cycle air cooled gas engine Displacement .
7 DESCRIPTION 35703 Kickback Safety This saw is equipped with the following safety equipment: ■ Operator activated and Inertial type chain brake. In the event of kickback, kickback energy either for.
8 DESCRIPTION WARNING! Either of the following reactions could cause you to lose control of your saw while cutting, possibly resulting in serious injury! 1. Kickback can occur whenever the guide bar nose or tip contact an object while the saw is running.
9 DESCRIPTION WARNING! NOTE: These safety precautions are intended primarily for consumers or occasional users. When using this chain saw for logging purposes, refer to: CFR Section 1910. 266 (5); 2.5.1 of the American National Safety Standard; Requirements for Pulp- wood Logging ANSI 03.
10 DESCRIPTION WARNING! ■ Install the appropriate guide-bar scabbard before transporting the saw. ■ Never operate a saw that is damaged, improperly adjusted, or not completely and securely assembled. ■ Use only Shindaiwa-recommended parts when repairing or servicing this saw.
11 ASSEMBLY 35707 IMPORTANT! The chain brake must be completely disengaged before removing or installing the clutch cover! 1. Use the 13 mm socket wrench to remove the clutch cover nuts. Turn the nuts counter-clockwise to remove. 2. Slide the rubber stopper downward and unhook the support arm from the brake lever (see illustration below).
12 ASSEMBLY 35708 57704 Brake lever support arm 4. Remove the packing spacer. 5. Install the guide bar. 6. Install the chain loop over the drive sprocket, and then align the chain drive links within the guide bar groove. Make sure the cutters are properly oriented.
13 OPERATION 35710 WARNING! Inspect chain tension often during operation, especially when breaking in a new chain. A loose saw chain can unexpectedly jump the guide bar during operation, possibly causing serious personal injury! IMPORTANT! Proper chain adjustment is essential for maximum performance, chain life, and operator safety.
14 OPERATION Mixing Fuel/Filling With Fuel WARNING! Minimize the risk of fire burns and personal injury! IMPORTANT! Shindaiwa high-performance 2-cycle engines are designed to operate on a 50:1 mixture of unleaded gasoline and 2-cycle engine oil.
15 OPERATION 35711 Fuel Cap Oil Cap 3. Refer to following chart for examples of 50:1 fuel to oil mix quantities. 4. Place the saw on a hard surface with the fuel cap up and wipe any chips or debris from around the fuel cap. Oil Requirements 䡵 When available, use Shindaiwa Premium bar & chain oil.
16 OPERATION 35712 Preparing to Start the Saw Throttle Lockout Lever Throttle Lock Button Throttle Trigger Ignition Switch WARNING! The saw chain will rotate when the saw is started! Clear a safe work area before starting the saw! IMPORTANT! Engine ignition is controlled by a two- position “ON-OFF” switch located below the throttle lever.
17 OPERATION 35714 Starting the Saw 1. Place the saw on the ground. 2. Secure the saw firmly as shown. 3. Grip the starter handle with your right hand, pull the starter cord slowly until you feel the starter engage, then… 4. Start the saw by pulling the starter cord upward rapidly.
18 35719 Starting a Flooded Engine 1. Disconnect the spark plug lead, then use the spark plug wrench to remove the spark plug (turn counter-clockwise to remove). 2. If the spark plug is fouled or is soaked with fuel, clean or replace the plug as required.
19 Carburetor Adjustments A clean and unrestricted airflow is essential to your saw engine’s perfor- mance and durability! Before attempt- ing any carburetor adjustments, inspect and clean the engine air filter as required! Procedures for maintain- ing this saw’s air cleaner are described on page 27 of this manual.
20 Low and High Mixture Adjust- ments for Non Emission Compli- ance Engines. Low Speed Mixture (engine idling at operating temperature. 1. Using a small screwdriver, slowly turn the low speed mixture screw clockwise (lean mixture) and note any changes in engine rpm.
Een belangrijk punt na aankoop van elk apparaat Shindaiwa 72362-93115 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Shindaiwa 72362-93115 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Shindaiwa 72362-93115 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Shindaiwa 72362-93115 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Shindaiwa 72362-93115 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Shindaiwa 72362-93115 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Shindaiwa 72362-93115 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Shindaiwa 72362-93115 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
