Gebruiksaanwijzing /service van het product LE261/EVC van de fabrikant Shindaiwa
Ga naar pagina of 20
ENGLISH SHIND AIWA OWNER’S/OPERA T OR’S MANU AL LE261/EV C LA WN EDGER Par t Number 62721-94310 Rev . 11/06 Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit.
2 Contents Introduction PAGE The Shindaiwa 261-series of hand-held power tools has been designed and built to deliver superior per for mance and reliability without compromise to quality , comfor t, safety or durability .
3 WARNING! Use Good Judgment AL W A YS wear eye protection to shield against thrown objects. NEVER run the engine when transport- ing the unit. NEVER run the engine indoors! Make sure there is always good ventilation. Fumes from engine exhaust can cause serious injury or death.
4 Safety Labels Figure 3 IMPORT ANT Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer .
5 26103 Using the accompanying illustrations as a guide, familiarize yourself with your unit and its various components. Understanding your unit helps ensure top per for mance, long ser vice life, and safer operation.
6 2. Use the 4 mm hex wrench to loosen the tube clamp screw . See Figure 5. 3. Slide the outer tube into the tube clamp until the tube bottoms. If installation is dif ficult, rotate the outer tube or main- shaft slightly until you feel the mainshaft engage with the powerhead.
7 26109 26110 Assembly Throttle Cable Free Play Adjustment 1. Move the throttle lever to check for smooth operation. Any stif fness or bind- ing must be cor r ected before using the product. 2. Actuate the throttle lever to check for free play of approximately 4-6 mm (1/4”) in the idle position.
8 WARNING! The LE261 is designed for use with a single blade only! Never operate the LE261 without the cutting attachment shield installed and tightly secured! 26118 Assembly Attachment Shield and Edger Blade Mount the Edger Blade. 1. Install holder A onto the output shaft.
9 IMPORT ANT! Repeated cranking of the engine with the choke CLOSED will lead to engine ood - ing. If the engine fails to start after several attempts, move the choke lever to the OPEN position and continue cranking. 26121 26120 Star ting the Engine 5.
10 26125 1. Place the trimmer on the ground, then star t the engine and allow it to idle 2-3 minutes until war m. 2 If the attachment rotates when the engine is at idle, reduce the idle speed by tur ning the idle adjustment scr ew counter-clockwise. 3.
11 26130 The edger’s depth of cut is controlled by a combination of operator height, blade wear , and the positioning of the edger’s guide wheel. T o Adjust Blade Height: 1. Loosen the guide wheel adjusting knob. See Figure 21. 2. Raise or lower the guide wheel to the desired setting.
12 Daily Maintenance Remove all dir t and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as neces- sar y . Prior to each work day , per for m the following: Carefully remove any accumulations of dir t or debris from the muf fler and fuel tank.
13 26138 26135 50-Hour Maintenance Ever y 50 hours of operation (more frequently in sever e conditions): Remove and clean the cylinder cover and clean grass and dir t from the cylin- der fins. Remove the cutting attachment, cutting attachment holder and the gear shaft collar .
14 CA T AL YST MUFFLER 26139 135-Hour Maintenance 1. Remove the muf fler cover from the engine. 2. Remove the two 5 mm muf fler scr ews. Remove the lower muf fler screw , then lift the muf fler assembly from the en- gine. See Figure 29. 3. Remove the rear muf fler shield bolt.
15 NO T r oubleshooting Guide Does the engine crank? Good compression? Does the tank contain fresh fuel of the proper grade? Is fuel visible and moving in the retur n line when priming? Is there spark at the spark plug wire ter minal? Check the spark plug.
16 T r oubleshooting Guide (continued) ADDITIONAL PR OBLEMS Poor acceleration. Clogged air filter . Clogged fuel filter . Lean fuel/air mixture. Idle speed set too low . Switch tur ned of f. Fuel tank empty . Clogged fuel filter . W ater in the fuel.
17 Y our Warranty Rights and Obligations The Califor nia Air Resour ces Board, the U.S. Envir onmental Protection Agency and Shindaiwa Corporation are pleased to explain the exhaust and evaporative emission control system war ranty on your new small of f-r oad (non-road) engine.
18 Notes.
19 Notes.
20 Shindaiwa Inc. 11975 S.W . Her man Rd. T ualatin, Oregon 97062 USA Telephone: 503 692-3070 Fax: 503 692-6696 www .shindaiwa.com Shindaiwa Corporation Head Of fice: 6-2-11, Ozuka-Nishi Asaminami-Ku, Hiroshima 731-3167, Japan Telephone: 81-82-849-2220 Fax: 81-82-849-2481 ©2006 Shindaiwa, Inc.
Een belangrijk punt na aankoop van elk apparaat Shindaiwa LE261/EVC (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Shindaiwa LE261/EVC heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Shindaiwa LE261/EVC vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Shindaiwa LE261/EVC leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Shindaiwa LE261/EVC krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Shindaiwa LE261/EVC bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Shindaiwa LE261/EVC kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Shindaiwa LE261/EVC . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
