Gebruiksaanwijzing /service van het product SCM810AZ van de fabrikant Shure
Ga naar pagina of 17
User Guide © 200 8 Shure Incorporated 27A8868 (Rev . 2 ) Printed in U.S.A. SCM810/SCM810AZ SCM810/SCM810AZ EIGHT-CHANNEL MICROPHONE MIXER EIGHT-CHANNEL MICROPHONE MIXER SCM810/SCM810C SCM810/SCM810C .
2 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SYSTEM FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 DESCRIPTION The Shure Model SCM810/E is an eight-channel automatic microphone mixer designed for use in sound re inforcement, audio recording, and broadcast applications. The SCM810 dr amatically improve s audio quality in any application w here multiple microphones are re quired.
4 FRONT PANEL FEATURES MODEL SCM810 FRONT PANEL FIGURE 1 Microphone Channel Gain Controls 1–8: Allows adjustment of microphone gain. Input LED 1–8: Lights green when channel is active; lights red at 6 dB below clipping level.
5 DIP SWITCHES The rear-panel DIP switch provides the following setup options. The posi- tions shown in bold type are the factory settings. NOTE: Switch positions and effects are shown in Figure 3 and a lso on the mixer label.
6 INSTALLATION AND SYSTEM SETUP RACK MOUNTING THE MIXER T o mount the SCM810 in a st and ard 483 mm (19-inch) audio equipment rack, slide the mixer into the rack and secure it with the supplied Phillips head screws, as shown in Figure 4. Use all four screws.
7 EQUALIZER FUNCTIONS Low Cut Filter (High-Pass) The low-cut (or high -pass) filter allo ws all frequencies above its cutoff point to pass from filter input to filter output without attenuation, while fr equencies below the cutoff are attenuated (see Figure 6).
8 NETWORKING MULTIPLE MIXERS If additional inputs are needed, more SCM810 mixers (as many as 50) can be “linked” using supplied link cables. Such a conf iguration can provide up to 400 microphone inputs. T o link multiple mixers, connect the LINK OUT of the first mixer to the LINK IN of the next mixer , and so on (see Figure 8).
9 SPECIFICATIONS Measurement Conditions (unless ot herwise specified): Line voltage 120 V ac, 60 Hz (SCM810) or 230 Vac, 50 Hz (SCM810E); full gain; 1 kHz, one channel activated; source impedances: Mi.
10 ADVANCED FUNCTIONS LOGIC CONNECTION SPECIFICATIONS The logic functions of the SCM810 ex pand the mixer's range of inst allation and control options. Logic can be used for everything from simple cough switches to elaborate computer-c ontrolled room systems.
11 SUGGESTED LOGIC APPLICATIONS This section contains suggestions on t he uses of the SCM810's logic capa- bilities. Note that uses of these func tions are not limited to the listed appli- cations. The user is limited only by individual imagination and creativity .
12 Inhibiting Gating for Unwa nted Sounds As described in the Operating Principles section, MaxBus attempts to acti- vate only one microphone per sound source. Muting a microphone channel prevents its audio from appearing at the mixer's output. However , the mut- ed microphone still communicates with other mic channels via MaxBus.
13 Diode Isolation of Logic Controls T wo or more control functions using the same logic pins can be isolated with diodes. In this manner a chann el can be muted by an overall group mute switch, or by its own cough button (see Figure 19-Channels 1, 3 and 5 modified).
14 INTERNAL MODIFICATIONS W ARNING: All modifications must be performed by qualified service tech- nicians. This section describes SCM810 modifi cations that can be made using sol- der “jumpers” on the printed circuit board; the pads where jumpers may be used are placed close together so that a single solder drop functions as a jumper .
15 SCM810 Speech Gate for Mixing Console The SCM810 can be used in conjunction with large mixing consoles to pro- vide automatic mixing for talk shows, panel discussions, and news shows. Large consoles have channel insert jac ks so that e xternal signal process- ing devices can be patched into individual channel si gnal paths.
16 Increase Hold Time In addition to the dip switch SW702 options of 0.4- and 1.0-second hold time, the hold time can be increased to 1.5 seconds. (Mor e than 1.5 sec- onds is not recommended.) Procedure: Install a 470 k Ω resistor across jumper points X902.
SHURE Incorporated http://ww w.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 607 14-4608, U.S.A. Phone: 847-600-2000 U.
Een belangrijk punt na aankoop van elk apparaat Shure SCM810AZ (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Shure SCM810AZ heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Shure SCM810AZ vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Shure SCM810AZ leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Shure SCM810AZ krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Shure SCM810AZ bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Shure SCM810AZ kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Shure SCM810AZ . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
