Gebruiksaanwijzing /service van het product 1692150 van de fabrikant Simplicity
Ga naar pagina of 22
Print V endor Instructions Ho w to use this file Operator’ s Manuals P aper Size: • 11x17 • Body - 50 lbs brilliant white offset or equivalent • Cov er - on pre-printed two tone “Sw ash” stock.
THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT).
OPERA T OR’S MANU AL Clean Sweep T win Catcher s Mfg. No. Description 1692149 Clean Sweep Twin Catcher (for 30” Mower Decks) 1692150 Clean Sweep Twin Catcher (for 34” Mower Decks) 1709142-08 Rev.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc.
1 T able of Contents Normal Installation & Remov al Installation & Remov al .....................................5 T roubleshooting Char t ................................................................7 Initial Setup & Assembl y 30” Models - Blade and Adapter Assembly .
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed.
3 BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.
4 Operation & Storage BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris, which may be caught or thrown by the mower blades. Clean the tube with mild detergent (other products may damage tube). Inspection windows can be removed to be cleaned.
5 Normal Installation & Removal INST ALLA TION & REMO V AL NOTE: For first-time installation, refer to Initial Setup & Installation. NOTE: If mower deck is equipped with Mulching Kit, the mulching baffles must be removed for grass collection.
6 Normal Installation & Removal 3. Open grass bag cover and install grass bag frames (A, figure 3) to support brackets (B). 4. On 30" mower, lift the deflector (C) up and install the adapter .
7 T roubleshooting The following table provides troubleshooting instructions for the more common and easily corrected problems. For problems not covered in the table, see your dealer. W ARNING To avoid serious Injury, perform maintenance on the grass catcher only after stopping the engine and waiting for all moving parts to come to a complete stop.
8 Initial Setup & Assembly 30” MODELS - BLADE AND AD APTER ASSEMBL Y Blade Assembl y - 30” Mower 1. Remove the mower deck to access the blade or using an overhead hoist, elevate the front of the unit to access the mower blade. 2. Mount the lifts (B, Figure 6) to the discharge side of the blade as shown.
9 Initial Setup - 30” Models 3. Install 5/16-18 x 2-1/4 carriage bolt (A, figure 8) through front hole in mower deck along with cup (B), whiz flange nut (C), wing nut (D) and center lock nut (E). Nut (C) must be seated inside cup and center lock nut (E) should be flush with end of carriage bolt.
10 Initial Setup - 34” Models 34" MODELS - B AFFLE, BLADE, & AD APTER ASSEMBL Y Install Baffle 1. Remove mower deck from rider. Position mower deck upright and support in this position. 2. Position baffle with notched end towards discharge side opening, Install all hardware as shown in figure 10.
11 Initial Setup - 34” Models Install Blades - Early Models with Splined Arbor 1. Remove existing discharge-side blade but retain hardware. Remove the retaining band (E, figure 11 b) from the arbor shaft and remove the existing splined adapter (3-3/8" O.
12 Initial Setup - All Models FRAME & B A GGER SUPPORT ASSEMBL Y - ALL MODELS Note: Units with 0510 transmissions use anchors (A, fig- ure 13) with a notch, all other units use anchor with no notch.
13 Initial Setup - All Models GRASS CA TCHER ASSEMBL Y - ALL MODELS NOTE: Cover and bag support are packaged as an assembly with long clevis pins and clips. It may be easier to separate components for the following step. 1. Install horizontal bag support (A, figure 14) to upright catcher support (B) holes as shown.
14 Initial Setup - All Models 5. Open cover and fasten cable (A, figure 17) to tube support (B) to prevent cover from going over center when opened. Loop end of cable fits over washer (C). Figure 17. A. Cable B. Support C. Washer Figure 18. A. Grass Bag Frame B.
15 Initial Setup - All Models 7. Apply dry talc powder to rubber seal at cover open- ing. Install tube (A, figure 19) as far as possible into opening to clear adapter and install over adapter. Figure 19. A. Tube B. Wire Form Location Figure 20. A. Wire Form B.
Installation Instructions Baffle Kit Part No. 1686783 INST ALLA TION 1. Remove the hardware (D) securing the plastic elbow (C) to the metal support plate (B). 2. Insert the baffle (A) in between the support plate (B) and elbow (C). 3. Reinstall the hardware (D).
INSTALLATION INSTRUCTIONS EXHAUST SHIELD KIT MFG. NO. 1666610 1. Raise the seat deck to expose the right-hand top duct. 2. See figure 1. Cut out the template below and place it on the duct with the edges aligned. Tape the template in place and drill out the holes as indicat- ed using a 13/W drill bit.
18 T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
Een belangrijk punt na aankoop van elk apparaat Simplicity 1692150 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Simplicity 1692150 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Simplicity 1692150 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Simplicity 1692150 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Simplicity 1692150 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Simplicity 1692150 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Simplicity 1692150 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Simplicity 1692150 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
