Gebruiksaanwijzing /service van het product 1694144 van de fabrikant Simplicity
Ga naar pagina of 30
A TT A CHMENT OPERA T OR’S MANU AL 42” Snowthrower Attachment Mfg. No. Description 1694144 42” Single-Stage Snowthrower 1694295 42” Single-Stage Snowthrower 46” Snowthrower Attachment Mfg.
1 T able of Contents T roub leshooting, Adjustments & Service T roub leshooting Char t ...................................11 Drive Chain Adjustment .................................12 Skid Shoe Adjustment ...................................12 Electric Chute Rotator Gear .
2 This machine is capable to amputating hands and feet. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
3 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
4 Safety Decals Part No. 1716532 Auger Danger Decal Part No. 1722674 Discharge Chute Danger Decal Part No. 1716531 Main Operation Warning Decal WHEN OPERA TING WITH SNO WTHRO WER, REAR WHEEL WEIGHTS ARE REQUIRED . C A UTION 1716540 Part No. 1716540 Rear Wheel Weights Required Part No.
5 Safety Information Required Accessories It is required that tire chains and two rear wheel weights or Quick Tach Weights are used. Never operate on slopes greater than 17.6% (10°). Recommended Accessories A rear-mounted weight box can also be added for additional traction.
Features & Controls 6 A. Electric Spout Rotator Switch Controls the electric spout rotator. B. PT O Switch Engages and disengages the PTO to start and stop the snowthrower. C. Hydraulic Attachment Lift Le ver NOTE: The hydraulic lift will only work with the engine running and the parking brake disengaged.
7 General Operating Instructions Checks Bef ore Star ting IMPORTANT NOTE: Refer to Tractor Operator’s Manual for important information concerning safely storing your tractor. 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service.
8 General Operating Instructions Snow Remo val Suggestions • Determine the best snow removal pattern before beginning. • Wind direction is an important factor to consider. Rotate the spout to discharge snow downwind. • Plan the pattern so that you avoid throwing snow on cleared areas and on yourself as you are operating.
9 Maintenance Schedule For Normal Care General Lubrication Lubricate the snowthrower as shown in Figure 2. Where an oil can is shown use 30 weight oil. Where a grease gun is shown, use lithium grease. Lubricate Dischar ge Chute Lubricate the ring gear at the base of the discharge chute with lithium grease.
10 Maintenance Inspect, Adjust, & Lubricate Drive Chain See Figure 3. 1. Remove the two flange nuts (A) and chain guard (B). 2. Check the chain. Replace chain if worn or damaged. 3. There should be no slack in the chain, and the sprockets (D and E) should be aligned.
11 T roubleshooting, Adjustments, & Service TR OUBLESHOO TING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly.
12 T roubleshooting, Adjustments, & Service Figure 5. Adjusting Skid Shoes Drive Chain Adjustment See Inspect, Adjust & Lubricate Drive Chain in the MAIN- TENANCE Section. Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface.
13 T roubleshooting, Adjustments, & Service Figure 7. Adjusting Lift Rod A. Front Set Collar B. Spring C. Rear Set Collar Lift Rod Adjustment In the fully raised position the attachment should be 4”-5” off the ground. In the fully lowered position, the lift rod should compress the spring creating downward pressure on the blade.
14 T roubleshooting, Adjustments, & Service Belt Replacement 1. Loosen the drive belt by turning the handle (C, Figure 8). 2. Remove the belt from the pulley (D, Figure 9) inside the snowthrower and remove the snowthrower from the tractor. 3. Loosen the lockwashers and nuts securing two belt stops on idler pulleys (A and E, Figure 4).
6 5 7 8 9 10 11 4 3 2 28 1 15 14 13 12 16 19 20 17 18 21 22 23 24 25 26 27 15 Initial Setup & Assembly Ref Qty Description 1 1 SNOWTHROWER 2 2 GUIDE, Chute, Hold-Down 3 2 SCREW, Plastite 4 1 DISCHARGE CHUTE ASSY.
16 Initial Setup & Assembly Figure 11. Assemble Discharge Chute A. Plastite Screw B. Hold-Down C. Chute Ring D. reinforcement Ring Gear Figure 12. Discharge Chute Motor Adjustment A. Adjustment Screws B. Plastic Cover Figure 13. Skid Shoe Installation A.
17 Initial Setup & Assembly Install Chute Rotator Switch and Harness 1. Remove the plug from the switch mounting hole in the right side of the dashboard. 2. Route the switch harness (C, F, Figure 15) through the frame and dashboard as shown. 3. Install the switch (G) in the dashboard and connect the upper end of the switch harness (F) to it.
18 Initial Setup & Assembly Figure 17. Install Remote Deflector Control A. Clevis Pin B. Deflector Control Handle C. Mounting Bracket D. Hair Pin Clip A B C D Mount Remote Deflector Control 1. Using the template included in the back of this manu- al, drill two 9/32” holes in the dashboard to mount the remote chute control.
19 Initial Setup & Assembly Figure 18. Install Snowthrower A. Hitch Pin B. Hair Pin Clip Figure 19. Lift Rod - Front A. Lift Rod Assembly B. Hair Pin Clip C. Lift Arm Figure 20. Lift Rod - Front A. Lift Rod Assembly B. Hair Pin Clip C. Lift Arm Install Snowthr ower CONNECT TO HITCH 1.
20 Initial Setup & Assembly INSTALL ASSIST SPRING 4. Lift the snowthrower up fully and support with wood blocks. 5. Assemble the lift assist spring (B, Figure 21) and spring bracket (C). Install the spring assist bracket (C) in the front bumper. Be sure the spring notch is in the lower position.
21 Initial Setup & Assembly B C B D A Figure 23. Belt Routing A. Snowthrower Pulley (V-pulley) B. Back-side Idler Pulley C. Electric Clutch Pulley (V-pulley) D. Idler Pulley (V-pulley) Figure 24. Adjusting Belt Tension A. Trunnion E. Idler Pulley B.
22 Removal & Normal Installation Remov al 1. Fully raise and support the snowthrower with wood blocks. 2. Release the lift assist spring. Remove the spring and spring bracket (E, Figure 25) from the tractor.
23 Removing & Installing the Snowthrower B C B D A Figure 27. Belt Routing A. Snowthrower Pulley (V-pulley) B. Back-side Idler Pulley C. Electric Clutch Pulley (V-pulley) D. Idler Pulley (V-pulley) Figure 26. Adjusting Belt Tension A. Trunnion E. Idler Pulley B.
24 T ractor Lift Linkage A F C D G Figure 29. Lift Link - Manual Lift Models A. Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E.
25 T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
26 Mounting Remote Deflector Control Line Template Up with Edge of Plastic Dashboard Mark and Drill One 9/32” Hole Mount Bracket and align with Line Mark and Drill One 9/32” Hole MOUNTING REMO TE DEFLECT OR CONTR OL NOTE: Read through instructions before beginning.
27 T emplate Line Template Up with Top Crease of Plastic Dashboard Line Template Up with Edge of Plastic Dashboard Mark and Drill One 9/32” Hole.
28 T emplate.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc.
Een belangrijk punt na aankoop van elk apparaat Simplicity 1694144 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Simplicity 1694144 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Simplicity 1694144 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Simplicity 1694144 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Simplicity 1694144 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Simplicity 1694144 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Simplicity 1694144 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Simplicity 1694144 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
