Gebruiksaanwijzing /service van het product P1214-E van de fabrikant Axis
Ga naar pagina of 49
USER MANUAL AXIS P1214–E Network Camera.
About this document This manual is intended for admini strators and users of the AXIS P1214-E Network Camera, a nd is applicable to fi rmware 5.40 and later. It includes instruction s for using and managing the product on your network. Previous experience of networking will be of use when using this product.
AXIS P12 14–E Netw ork Camer a T able o f Content s H a r d w a r e O v e r v i e w ....... ................... ................ 4 C o n n e c t o r s ............. ............ ............. ............ .. 4 L E DI n d i c a t o r s ........... ..
AXIS P12 14–E Netw ork Camer a H a rd w a re O ve r v i ew Hardware Overview 10 11 9 8 7 3 2 1 6 5 4 12 13 14 1 Power indica tor LED 2 Status indicator LED 3 Network indicator LED 4 SD card slot (mi.
AXIS P12 14–E Netw ork Camer a H a rd w a re O ve r v i ew NOTICE To prevent corruption of recordings, the S D card should be unmounted before removal.
AXIS P12 14–E Netw ork Camer a H a rd w a re O ve r v i ew 1. Cut the cable to the desired len gth. Measure from the sensor unit. 2. Strip the plastic outer coating from the end of the cable. 3. Peel back the shield. 4. Flatten the colored wire s in the order described below.
AXIS P12 14–E Netw ork Camer a A ccessing the P r oduct Accessing the Product To install the Axis product, refer to the Installation Guide supplie d with the pro duct.
AXIS P12 14–E Netw ork Camer a A ccessing the P r oduct Access from the Internet Once connected, the Axis product is accessible on your local net work (LAN). To access the product from the Internet you must con fi gure your network router to allow incoming data traf fi c to the product.
AXIS P12 14–E Netw ork Camer a A ccessing the P r oduct Select the power line f req uency (50 Hz or 60 Hz) used at the locat ion of the Axis product. Selecting the wrong frequency may cause image fl i c k e ri ft h ep r o d u c ti su s e di n fl uorescent light environments.
AXIS P12 14–E Netw ork Camer a A ccessing the P r oduct For more information about a ction rules, see Events on pa ge 25 . To show the manual trigger buttons in the Live View page: 1. Go to Setup > Live View Layout . 2. Under Action Buttons ,s e l e c t Show manual trigger button .
AXIS P12 14–E Netw ork Camer a Media Str ea ms Media Streams The Axis product provides severa l video stream forma ts. Your re quirements and the properties of y our netw ork will determine the type you use. The Live View pag e in the product provides access to H .
AXIS P12 14–E Netw ork Camer a Media Str ea ms T h eA M CC o n t r o lP a n e lc a nb eu s e dt oc o n fi gure various video se ttings. Please see the AXIS Media Contro l User’s Manual for more information. The AMC Control Panel is automa tically installed on fi rst use, after which it can be con fi gured.
AXIS P12 14–E Netw ork Camer a Media Str ea ms Note • <ip>= IP addess • The Axis product s upports QuickTim e 6.5.1 and later. • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths a bove, although Axis does not guarantee this.
AXIS P12 14–E Netw ork Camer a Settin g Up the P r oduct Setting Up the Product The Axis product can be con fi g ured by users with administrator or operator r ights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page.
AXIS P12 14–E Netw ork Camer a Video Video It is possible to con fi gure the follo wing video features in yo ur Axis product: • Video stream. See page 15 . •S t r e a m p r o fi les. See page 16 . • Camera settings. See page 17 . • Overlay imag e.
AXIS P12 14–E Netw ork Camer a Video Image The default image s etting s can be con fi gured under Video> Video Stream . Select the Image tab. The following settings are a vailable: • Resolution . Select the default resolution. • Compression .
AXIS P12 14–E Netw ork Camer a Video Camera Settings The Video > Camera Settings page provides access to advanced image settings for the Axis product. Image Appearance Increasing the Color level increases the color saturation. The value 100 gives m aximum color saturation.
AXIS P12 14–E Netw ork Camer a Video 3. To include date and time, select Include date and In clud e time . 4. To include a text string, select Incl ude text and enter the text in the fi eld. Modi fi ers can be used, see Fi le Namin g & Date/Time Form ats in the o nline he lp .
AXIS P12 14–E Netw ork Camer a Live Vie w Con fi g Live View Con fi g You can customize the Live View page and alter it to suit your requirements. It is possible to d e fi ne the following features of t h eL i v eV i e wp a g e . •S t r e a m P r o fi le.
AXIS P12 14–E Netw ork Camer a Live Vie w Con fi g Browser Viewer Description AMC Recommended viewer in Internet Explorer (H.264/Motion JPEG). QuickTime H.264. Java applet A slower imaging alter n ative to AMC (Motion JPEG). Require s one of the following installed on the client: • JVM (J2SE) 1.
AXIS P12 14–E Netw ork Camer a Live Vie w Con fi g For more information about I/O ports, see I/O Ports on page 38 . 21.
AXIS P12 14–E Netw ork Camer a Detector s Detectors Camera Tampering Camera Tampering can genera te an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. To send an alarm, for example an email, an action rule must be set up.
AXIS P12 14–E Netw ork Camer a Detector s Note Using the motion detection feature may dec rease the product’s overall p erformance. Set Up Motion Detection Windows To set up a motion detection Includ e Window, follow these instructions : 1. Go to Detectors > Motion Detection .
AXIS P12 14–E Netw ork Camer a Applications Applications Third p arty ap plicatio ns can be uploaded to and installed on the Axis product. For information a bout available ap plications, downloads, trials and licenses, go to www.
AXIS P12 14–E Netw ork Camer a Ev e n ts Events The Axis product can be con fi gured to perform actions when diffe rent events occur, for example, start a recording when motion i s detected. The set of conditions that de fi nes how and when the action is triggered is called an Action Rule .
AXIS P12 14–E Netw ork Camer a Ev e n ts Setting Up an Action Rule An action rule de fi nes the conditions that m u st be met for the product to pe rform an action, f or examp le record video or send email noti fi cations. If multiple conditions are de fi ned, all must be met to trigger the action.
AXIS P12 14–E Netw ork Camer a Ev e n ts Note A network share can also b e used as a storage device for recorded video. Go to System Options > Storage to con fi gure a network share before setting up a continuous re c o r d i n go ra na c t i o nr u l et or e c o r dv i d e o .
AXIS P12 14–E Netw ork Camer a Re c o rd i ng s Recordings T h eA x i sp r o d u c tc a nb ec o n fi gured to record video continuously or according to an action rule: • To start a continuous recording, see page 28 . • To set up action rule s, see page 26 .
AXIS P12 14–E Netw ork Camer a Re c o rd i ng s Note If a new stream pro fi le is selected while a recording is ongoing, the reco rding will be stopped and saved in the reco rding list and a new recording with the new stream pro fi le will start.
AXIS P12 14–E Netw ork Camer a System Options System Options Security Users User access control is enabled by default and can be con fi gured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords.
AXIS P12 14–E Netw ork Camer a System Options IEEE 802.1X IEEE 802.1X is a s tandard for port-based Network Admission Control p roviding secure authentication of wired and wireless network devices. IEEE 802.1X is based on EAP (Extensible Authentication P rotocol).
AXIS P12 14–E Netw ork Camer a System Options If using a host name for the NTP server, a DNS server must be con fi gured. See DNS Con fi guration on page 34 . • Set m anually allows you to ma nuall y set date and time. If using an NTP ser ver, select your Time zone from the dro p-down list.
AXIS P12 14–E Netw ork Camer a System Options Linux/Unix syntax arp -s <IP address> <serial number> temp ping -s 408 <IP address> Linux/Unix example arp -s 192.
AXIS P12 14–E Netw ork Camer a System Options Advanced TCP/IP Settings DNS Con fi guration DNS (Domain Name Service) provides the translation of host names to IP a ddresses. The DNS settings are con fi gured under System Options > Network > TCP/IP > Advanced .
AXIS P12 14–E Netw ork Camer a System Options NAT traversal (port mapping) for IPv4 A network router allows devices on a private network (LAN) to share a single connection to the Internet. This is done by forwarding network traf fi c from the private network to the “outside”, that is, the Int ernet.
AXIS P12 14–E Netw ork Camer a System Options QoS (Quality of Service) QoS (Quality of Service) guarantees a certain level of a speci fi ed resource to selected traf fi c on a network. A QoS-aware network prioritizes network traf fi c and provides a greater network reliability by co ntrolling the amount of bandwi dth an application may use.
AXIS P12 14–E Netw ork Camer a System Options RTP/H.264 The RTP port range and multicast settings are con fi gured under System Options > Network > RTP . The RTP port range de fi nes t he range of po rts from which the video ports are automatically selected.
AXIS P12 14–E Netw ork Camer a System Options Network Share Network share allows you to add network sto rage such as a NAS (Network Attached Storage) or any server that uses CIFS (Common Internet File System) and use them for storage of recordings. To add a network share: 1.
AXIS P12 14–E Netw ork Camer a System Options Click Defaul t to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The Axis product can also be reset to factory d efault using the control button, see Reset to Factory Default Settings on page 40 .
AXIS P12 14–E Netw ork Camer a System Options NOTICE Improper use may cause unexp ected behavio r a nd loss of contact with the Axis product. Axis strongly recommends that you do not use this function unless y ou understand the consequences. Axis Support does not provide assistance for problems with custom ized scripts.
AXIS P12 14–E Netw ork Camer a T r oubleshootin g Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your fi rst actions when tro u bleshooting a problem should be to check the current fi rmware version.
AXIS P12 14–E Netw ork Camer a T r oubleshootin g arp -s <IP address> <serial number> temp ping -s 408 <IP address> In Windows , type the following from a command/DOS prom pt (t hi.
AXIS P12 14–E Netw ork Camer a T r oubleshootin g The IP address has been changed by DHCP IP addresses obtained from a DH CP server are dynamic and may change. If the IP addr es s has been changed, use AXIS IP Utility or AXIS Camera Management to located the product on the network.
AXIS P12 14–E Netw ork Camer a T r oubleshootin g Why do I not get maximum frames per second? See Performance Considerations on page 48 . The maximum frames per se cond is dependent on the utility fr equency (60/50 Hz) of the Axis product. See Technical Speci fi cations on page 46 .
AXIS P12 14–E Netw ork Camer a T r oubleshootin g Storage and disk management problems Video cannot be recorded Check that the SD card is not write protected (that is, read only). SD card cannot be mounted Reformat the SD card and then click Mo unt.
AXIS P12 14–E Netw ork Camer a T echnical Speci fi cations Technical Speci fi cations Function/group Item Speci fi cations Model AXIS P1214-E Image sensor Progressive scan RGB CMOS 1/4” Lens f=2.
AXIS P12 14–E Netw ork Camer a T echnical Speci fi cations Function/group Item Speci fi cations External o utput activatio n Status LED Video access from web b rows er Camera live view Video recor.
AXIS P12 14–E Netw ork Camer a T echnical Speci fi cations Performance Considerations When settings up your s ystem, it is important to consider how variou s settings and situations will affect performance. Some factors affect the amount of bandwidth (the bit rate) required , others can affect the frame rate, and some affect both.
User Manual Ver. M2.2 AXIS P1214– E Network Camera Date: August 2012 © Axis Communications AB, 2012 Part No. 47 875.
Een belangrijk punt na aankoop van elk apparaat Axis P1214-E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Axis P1214-E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Axis P1214-E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Axis P1214-E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Axis P1214-E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Axis P1214-E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Axis P1214-E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Axis P1214-E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
