Gebruiksaanwijzing /service van het product 11305 van de fabrikant Snapper
Ga naar pagina of 24
Safety Instructions & Operator’s Manual for TWO STAGE LARGE FRAM E SNOW THROWER SERIES 5 MODELS 8245 9265 11305 MODEL NUMBER EXPLA NA TION 11 30 5 ENGINE HP SERIES DESIGNATION A UGER WIDT H 8 – 8.0 Engine HP (En gine Horse Pow er 24 – 24” A uger Width 5 – Series Designation 9 – 9.
2 IMPORTA NT SA FETY INST RUC TIONS WARNING: This pow erful mach ine is capable of amp utating hands and f eet and can throw objects that can cause injury a nd d a m ag e ! Failure to comply with the follow ing instruct ions may result in se rious injury to the operator or other persons.
3 IMPORTA NT SA FETY INST RUC TIONS OPERA TIONA L PRECA UTIONS (Continued From Pre vious Page) 7. DO NOT put hands or feet nea r or under rotatin g parts. Keep clear o f the discharge opening at all times. 8. St art engine only where exhaust fu mes will be safely dissipated.
4 TABLE OF CONTENTS SECTION 1 - IMPORTA NT SA FETY INSTRUCTIONS .......................... 2-3 TA BLE OF CO NTENTS ............................................................................ 4 SECTION 2 - OPERA TIN G INSTRUCTIONS ....................
5 Section 2 - OPERA TING INSTRUCTIONS 1.1 INTRODUCT ION Before s tarting m achine, vis ually check location of all operational contr ols and identify major parts discuss ed in Operator’s Manual.
6 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the f ollowing check s and per form the ser vice required bef ore each star t-up. 2.1.1. Check engine oil and add oil as needed to bring level up to the FULL m ark . Refer to engine owner’s m anual for oil specif ications 2.
7 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.1.9. Check the AC elec trical outlet that will be used and m ak e sure it is a polar ized outlet. The ma chine has a polarized plug (one blade of plug is wider than the other) that will accept a polarized extension co rd.
8 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A RTING , OPERATION & ST OPPING (RECOIL STA RT MODELS) (Go t o Page 9 for Elect ric Start M odels) (Continued From Pre vious Page) 2.2.2. PROPELLING SNOW THROWER IMPO RTANT: T his snow thrower has six forward speeds and one rever se speed.
9 Section 2 - OPERA TING INSTRUCTIONS 2.2 STARTING, OPERA TION & ST OPPING (RECOIL STA RT MODELS) 2.2.6. STOPPING - ENGINE , A UGER & WHEEL DRIVE Stop the auger /im peller and wheel drive by releasing the auger/im peller and wheel drive control levers .
10 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A RTING , OPERATION & ST OPPING (ELECTRIC STA RT M ODELS) (Go to Page 7 for Recoil Start Models) (Continue From Pre vious Page) WA RNING Objects can b e thrown b y the snow throw er wh ile it is in operation.
11 Section 3 - MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the snow thrower, use only genuine SNAPPER replacem ent parts. Contac t a local SNAPPER dealer for par ts and ser vice assistanc e. For the cor rect part or inform ation for a particular s now thrower, alway s m ention model and serial num ber.
12 Section 3 - MA INTENA NCE 3.4 ANNUA LLY (END OF EA CH SEA SON) Perfor m all m aintenanc e as desc ribed in the maintenanc e schedule. 3.4.1. Engine Refer to engine owner’s manual f or service instru ctio ns. 3.4.2. Spark Plug Refer to engine owner’s manual f or service instru ctio ns.
13 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt any adjustments, maintenan ce, service, or repair s, with engine running. Stop auger.
14 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt any adjustments, maintenan ce, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure w ire away from sp ark plug. Bef ore tilting machine, drain all the fuel f rom fuel tan k.
15 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt any adjustments, maintenan ce, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure w ire away from spark plug. Be for e tilting machin e, drain all the fu el from fuel tank.
16 Section 4 - REPA IR & A DJUSTMENTS 4.1.5. SKID SHOE A DJUSTM ENT NOTE: It is recom m ended to raise the auger /impeller housing when c learing rough or gr aveled surfac es. To raise auger/im peller the sk id shoes should be lowered. 1. Tilt m achine up and plac e a wooden block under auger/im peller housing.
17 Section 4 - REPA IR & A DJUSTMENTS 4.1.6. SINGLE HA NDLE CONTROL A DJUSTM ENT IMPO RTANT: Standing in the oper ator’s position, the lef t handle bar lever is f or wheel drive engagement and disengagem ent. The r ight handle bar lever is f or auger/im peller engagem ent and disengagem ent.
18 Section 4 - REPA IR & A DJUSTMENTS 4.1.7. AUGE R SHEA R BOLT REPLACE MENT IMPO RTANT: If engine is operating cor rectly and auger/im peller drive belt is not dam aged or severed, but the auger/im peller does not rotate it is possibly the auger/impeller s haft shear bolt.
19 TROUBLESHOOTING PROBL EM PROBA BLE CA USE CORRECTIVE A CTION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel or fuel/oil mix . Using Recoil Starter 2. Engine needs choking and priming. 2. Mov e choke control to “CHOKE” position.
20 3 YEA R LIMITED WA RRA NTY For thr ee ( 3) years from purc hase date f or the original purc haser's residential, non- com m erc ial use, SNAPPER , through any authorized SNA PPER dealer will r.
21 NOTES _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________.
22 NOTES _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________.
23 NOTES _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________.
24 Safety Instructions & Operator’s Manual for TWO STAGE LARGE FRAM E SNOW THROWER SERIES 5 IMPORTA NT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufac tured. The labels on those e ngines contain ver y important e missions infor mation and critical safety warn ings.
Een belangrijk punt na aankoop van elk apparaat Snapper 11305 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper 11305 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper 11305 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper 11305 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper 11305 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper 11305 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper 11305 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper 11305 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
