Gebruiksaanwijzing /service van het product 7800596 van de fabrikant Snapper
Ga naar pagina of 28
Operator’s Manual NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for further details.
Thank You for purchasing this quality-built Snapper product. We’re pleased that you placed your confidence in the Snapper brand. When operated and maintained according to the instructions in this manual, your Snapper product will provide many years of dependable service.
3 Operator Safety Features and Controls Operation Maintenance Troubleshooting Warranties Table of Contents Operator Safety ................................................................................................................. 4 Important Operator Safety Instructions .
www.snapper.com 4 Operator Safety ! ! Important Operator Safety Instructions WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons.
5 Operator Safety ! ! Important Operator Safety Instructions (Continued) Safe Handling of Gasoline (Continued From Previous Page) 6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the contain- ers on the ground away from the vehicle before filling.
www.snapper.com 6 Features and Controls IMPORTANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your Snapper dealer if you have questions. Features and Controls A. Oil Fill Cap and Dipstick B.
7 Operation Pre-Start Check List Make the following checks and perform the service required before each start-up. 1. Check the guards, deflectors, grass bag, adapter, and covers to make sure all are in place and securely tightened.
www.snapper.com 8 Operation Starting and Operation (Continued) Propelling the Mower (Self-Propelled Models Only) 1. Start the engine. Refer to the Section entitled “Starting and Operation – Engine and Blade”. 2. Move the ground speed control (A, Figure 4) to the desired speed position.
9 Operation Cutting Height Adjustment 1. Pull the height adjusting latch (A, Figure 6) outward and move to the desired cutting height. 2. Set all wheels at the same cutting height. The high- est cutting position is Notch 7 (Figure 7) . The lowest cutting position is Notch 1.
www.snapper.com 10 Operation Installing the Discharge Deflector 1. Remove the recycling cover. Refer to the Section enti- tled “Recycling Operation”.
11 Operation Installing the Recycling Plug (Optional Accessory on Some Models) 1. Install the recycling plug (A, Figure 11) if recycling is desired after the bag adapter is installed. Install the recycling plug completely and securely into the bag adapter (B) .
www.snapper.com 12 Maintenance Maintenance - Introduction To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number.
13 Maintenance Check Mower Blade 1. Disconnect the spark plug wire and secure the end away from the plug. 2. Tilt the mower up on its rear wheels for access to the blade cap screw (A, Figure 16) . Do not tilt the mower with the spark plug or carburetor down.
www.snapper.com 14 Maintenance Mower Blade Replacement Standard Blade Wear Limit 1. Inspect the blade (Figure 17) frequently for signs of excessive wear or damage: (A) New blade (B) Wear limit (notch starts) (C) Dangerous condition! Do not use on the mower! Replace with a new blade.
15 Maintenance Blade Sharpening (Continued) 4. Sharpen the blade on a grinding wheel at an angle of 22 to 28 degrees (B, Figure 20) . DO NOT sharpen the blade beyond the original cutting edge (A) . 5. Check blade for balance. If necessary, correct balance by grinding heavy end of blade.
www.snapper.com 16 Maintenance Driven and Drive Disc Service If the mower does not propel itself properly, check for the following problems: 1. Grease on the drive disc (A, Figure 22) causing slippage. 2. Broken or disconnected drive spring (B) . 3. Driven disc (C) is out of adjustment.
17 Maintenance Driven Disc Adjustment (Continued) 2. Remove the driven disc spring (A, Figure 25) from the driven disc assembly (B) . Also remove the pin and washer (C) from the transfer rod (D) , and remove the end of the transfer rod from the hole in the driven disc assembly.
www.snapper.com 18 Maintenance Driven Disc Replacement (Continued) 2. Using needle nose pliers, unhook the drive spring (A, Figure 28) and slide the driven disc assembly off the hex shaft. 3. Remove the two snap rings (A, Figure 29) which secure the rubber driven disc (B) to the driven disc assembly.
19 Maintenance Replacing the Bearing On the Pulley End Of the Hex Shaft To replace the bearing on the pulley end of the hex shaft, proceed as follows: 1. Hold the hex shaft with an adjustable wrench held next to the pulley. 2. Remove the 3/8” hex lock nut (B, Figure 30) , located on the outside of the right wheel bracket.
www.snapper.com 20 Maintenance Engine Drive Belt Replacement (Stretch Type Belts - Continued) IMPORTANT: Drain the fuel tank before tipping the mower. DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all.
21 Maintenance ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 7 X Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre-Clea.
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start Using Recoil Starter 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel. 2. Spark plug wire disconnected. 2. Place spark plug wire onto spark plug. Engine Stalls or Stops After Running 1.
23 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser’s residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of cha.
www.snapper.com 24 Notes Not for Reproduction.
25 Not for Reproduction.
www.snapper.com 26 Notes Not for Reproduction.
27 Notes Not for Reproduction.
www.snapper.com Snapper Products 535 Macon Street McDonough, GA 30253 21” STEEL DECK WALK MOWERS SERIES 20 1-800-935-2967 Engine Power Rating Information: The gross power rating for individual gas e.
Een belangrijk punt na aankoop van elk apparaat Snapper 7800596 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper 7800596 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper 7800596 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper 7800596 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper 7800596 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper 7800596 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper 7800596 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper 7800596 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
