Gebruiksaanwijzing /service van het product EYZ16335BVE van de fabrikant Snapper
Ga naar pagina of 32
1 Safety Instructions & Operator’s Manual for EUROPEAN SCRAMBLER HYDRO DRIVE SERIES 5 MODELS EYZ16335BVE MODEL NUMBER EXPLANATION E Y Z 16 33 5 B V E MODEL DESIGNATION ENGINE OPTIONS DRIVE SYSTE.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 7. Keep people and pets out of mow ing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area. 8. Check shields, deflectors, sw itches, blade controls and other safety dev ices frequently for proper operation and location.
4 IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE 1. DO NOT store machine or fuel container inside w here fumes may reach an open flame, spark or pilot light such as in a w ater heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ...................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON.
6 Section 1 - FAMILIARIZATION FIGURE 1.1 1. 1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER SCRAMBLER. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices.
7 Section 1 - FAMILIARIZATION – DECALS / SYMBOLS All operators should locate, read and understand all decals on the machine before attempting any operation of the machine. If any operator has difficulty in understa nding certain sy mbols incorporated in the decals, an authorized SNAPPER dealer should be contacted for explanation.
8 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 12 P.S.I. in front and 12 P.S.I. in rear tires.
9 Section 2 - OPERATING INSTRUCTIONS IMPORTANT: This SCRAMBLER is equipped w ith hydrostatic driv e. The forw ard, rearw ard and steering movement of the machine is controlled by a joystick lever. Joy stick operations should be performed only from the operator’s position in the seat.
10 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT operate blades in reverse. STOP BLADES. LOOK and SEE behind and down for children, pets and hazards before and w hile backing. 2.2.3. MOWER BLADE 1. With engine running, move engine speed control to the Rabbit or “fast” position.
11 Section 2 - OPERATING INSTRUCTIONS 2.3.5. CUTTING HEIGHT ADJUSTMENT This machine has seven different cutting height positions. IMPORTANT: When positioning the cutting deck into a higher cutting position, pull up on the deck lift handle only, it is not necessary to pull up on the release lever at the same time.
12 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the SCRAMBLER, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number.
13 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
14 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
15 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
16 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
17 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
18 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
19 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
20 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
21 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
22 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
23 Section 4 - ADJUSTMENTS & REPAIR 4.5.5. BATTERY TESTING There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current.
25 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact.
26 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Excessive Vibration 1. Damaged, out of balance or bent mo w er blades. 1. Service mower blade(s). 2. Loose blade components. 2. Service and tighten loose parts. 3. Loose or missing air lift (if equipped).
27 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 8 X Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Oil Fil.
28 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
29 PRIMARY MAINTENANCE.
30 PRIMARY MAINTENANCE.
31 PRIMARY MAINTENANCE.
32 PRIMARY MAINTENANCE.
33 Safety Instructions & Operator’s Manual for EUROPEAN SCRAMBLER HYDRO DRIVE SERIES 5 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
Een belangrijk punt na aankoop van elk apparaat Snapper EYZ16335BVE (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper EYZ16335BVE heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper EYZ16335BVE vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper EYZ16335BVE leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper EYZ16335BVE krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper EYZ16335BVE bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper EYZ16335BVE kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper EYZ16335BVE . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
