Gebruiksaanwijzing /service van het product GM2516BVG van de fabrikant Snapper
Ga naar pagina of 24
OPERA T OR’S MANU AL SIMPLICITY Mfg. No. Description 1694240 13HP Honda Walk-Behind Brush Mower 1694204 13HP Briggs Walk-Behind Brush Mower 1694205 13HP Kawasaki Walk-Behind Brush Mower FERRIS Mfg. No. Description 1694249 13HP Briggs Walk-Behind Brush Mower (BC25BE) 1694251 13HP Honda Walk-Behind Brush Mower (BC25H) GIANT-VAC Mfg.
1 T roub leshooting, Adjustment and Service .....14 Chart .....................................................................14 Travel Control Adjustment ....................................16 Blade Clutch Adjustment ................................
2 SAFE OPERA TION PRA CTICES FOR W ALK-BEHIND MO WERS This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the follow- ing safety instructions could result in serious injury or death. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual(s).
3 Safety Rules and Information SLOPE OPERA TION Slopes are a major factor related to slip and fall acci- dents, which can result in severe injury. All slopes require extra caution. If you feel uneasy on a slope, do not mow it. Do • Mow across the face of slopes; never up and down.
4 Safety Rules & Information SER VICE AND MAINTENANCE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. a) Use only an approved container. b) Never remove gas cap or add fuel with the engine running.
5 Identification Numbers Decal - Warning (7028490) Important Safety Operating Instructions. Read and understand before operating machine Decal - Engine Throttle Control (7029167) Models - All mowers D.
6 Features & Controls Engine On/Starter Rotate this key switch to the ON position before pulling on the starter rope. If the mower is equipped with the optional electric start- ing system, rotate the key past the ON position to engage the starter.
7 Operating the Mower Engage Disengage Figure 4 - Traction Drive / Freewheel Control ST AR TING THE ENGINE NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions.
8 Operating the Mower T o Pr opel Unit Forward: • Grasping both upper handle/safety bar (A, Figure 5) and lower portion of traction drive engagement bar (B) with both hands, slowly begin squeezing engage- ment bar up toward handle. The unit should begin moving forward.
9 Operating the Mower OFF RUN ST ART A Figure 7 - PTO Engaged A. Blade Engagement Lever in engaged position. OFF RUN ST ART A Figure 8 - PTO Disengaged A.
10 Operating the Mower A D C C B Figure 9 - Adjusting Height A. Skid B. Capscrew C. Washer D. Nut T O ADJUST CUTTING HEIGHT The front skids on the brush cutter have 3 sets of holes (Figure 9) for heig.
11 Regular Maintenance LUBRICA TION Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figure 10 as well as the lubrication points listed. Generally, all moving parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys.
12 Regular Maintenance TIRE PRESSURE Tire pressure is 20 psi (1.4 bar). B A TTER Y SER VICE Cleaning the Battery and Cables - 9HP Models Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (C, Figure 13a).
13 Regular Maintenance SER VICING THE MO WER BLADES Service Interval: Every 100 Hours or As Required 1. Raise the front end of the brush mower and securely support in the raised position. 2. Blades should be sharp and free of nicks and dents. If worn or damaged, replace the blades as described in following steps.
14 T roubleshooting, Adjustment, & Service TR OUBLESHOO TING PROBLEM CAUSE REMEDY Engine will not turnover or start. 1. PTO lever in the engaged position. Place in disengaged position. 2. Out of fuel. If the engine is hot, allow it to cool, then refill the fuel tank.
15 T roubleshooting, Adjustment & Service T r oubleshooting Cont. Blade will not engage. 1. Blade clutch rod too loose. See Blade Clutch Adjustment Section. 2. Blade belt worn or broken. Turn off engine and inspect belt. Adjust or replace as required.
16 T roubleshooting, Adjustment, & Service TRA VEL CONTROL ADJUSTMENT Serial Number 0-011903999 1. The Travel Control engagement bars (A, Figure 16a) should be an equal distance from the Upper Handle Bar. If they are not, adjust their position. 2.
17 T roubleshooting, Adjustment, & Service A D C B E Figure 17 - Blade Clutch Adjustment A. Clutch Rod B. Clutch Rod Lever C. Clutch Rod Fitting D.
18 T roubleshooting, Adjustment, & Service BLADE BRAKE ADJUSTMENT The mower blade should stop within 5 seconds after the Blade Engagement Lever is moved to the DISEN- GAGED position. This adjustment is checked by: 1. Remove blade clutch cover plate (A, Figure 19).
19 T roubleshooting, Adjustment, & Service A D B 1/8” Max. C Figure 21 - Traction Drive Belt Adjustment A. Transmission Pulley B. Drive Belt C. Engine Pulley D.
20 T roubleshooting, Adjustment & Service E D G F B C A Figure 24 - Belt Alignment A. Blade Drive Pulley B. Mower Belt C. Mower Tension Idler D. Transmission Pulley E.
21 Specifications Parts & Accessories ENGINEl BRIGGS HONDA KAWASAKI BRIGGS Engine 13 HP B&S 13 HP Honda 15 HP V-twin 16 HP B&S Transmission Hydro/Variable Hydro/Variable Hydro/Variable Hydro/Variable Ground Speed (mph) Infinite (.01 - 6) Infinite (.
22 Notes Not for Reproduction.
Products, Inc. 535 Macon Street/PO Box 777 McDonough, GA 30253 © Copyright 2003 Snapper Products, Inc. All Rights Reserved. Printed in USA. Not for Reproduction.
Een belangrijk punt na aankoop van elk apparaat Snapper GM2516BVG (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper GM2516BVG heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper GM2516BVG vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper GM2516BVG leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper GM2516BVG krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper GM2516BVG bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper GM2516BVG kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper GM2516BVG . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
