Gebruiksaanwijzing /service van het product HZT21481BV van de fabrikant Snapper
Ga naar pagina of 40
Safety Instructions & Operator's Manual for Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and p ay p articular attention to the "IMPORT ANT SAFETY INSTRUCTIONS" on Pages 2 - 4. Remember that all power equip- ment can be dangerous if used improperly .
2 ! ! IMPORT ANT SAFETY INSTRUCTIONS W ARNING: This powerful cutting machine is capable of amput ating hands and feet and can throw object s that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons.
3 ! ! IMPORT ANT SAFETY INSTRUCTIONS PREP ARA TION (Continued From Previous Page) 7. Keep people and pet s out of mowing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area. 8. Check shields, deflectors, switches, blade controls and other safety devices frequently for proper operation and location.
4 ! ! IMPORT ANT SAFETY INSTRUCTIONS TOWING 1. T ow only with a machine that has a hitch designed for towing. DO NOT att ach towed equipment except at the hitch point. 2. Follow the manufacturer's recommendation for weight limit s for towed equipment and towing on slopes.
5 T ABLE OF CONTENTS IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4 T ABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SECTION 1 - F AMILIARIZA TION .
6 Section 1 - F AMILIARIZA TION IMPORT ANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Cont act your Snapper dealer if you have questions. FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operators of the SNAPPER MID MOUNT ZERO TURNING HYDRO DRIVE.
7 Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROT A TING P ARTS KEEP A W A Y FROM MOVING P ARTS W ARNING ! GUARD OR GRASS CA TCHER MUST BE INST ALLED P ARKING BRAKE LEVER OPERA TION MOTION CONTRO.
8 Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER! ROT A TING BLADES FUEL GAUGE (2) CONTROL P ANEL IDENTIFICA TION DANGER! ROT A TING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA FUEL T ANK SELEC.
3.1 PRE-ST ART CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.
10 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS ROLL RELEASE: T o roll the machine without the engine running, pressure within the hydraulic pump s must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure.
11 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS 3.2.2. STOPPING ENGINE 1. S top engine by turning key to "ST OP" position. Move engine speed to the T urtle "SLOW" position and turn key to "STOP".
12 Section 3 - OPERA TING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever . IMPORT ANT : There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height.
13 Section 3 - OPERA TING INSTRUCTIONS 3.4.2. STOPPING MACHINE 1. Return motion control levers to the neutral position & the neutral lock position. IMPORT ANT : Operator must use hand assistance to bring both motion control levers to the neutral position & the neutral lock position.
14 Section 4 - MAINTENANCE 4.1 INTRODUCTION T o retain the quality of the SNAPPER mower , use gen- uine SNAPPER replacement part s only . Contact a local SNAPPER dealer for part s and service assis- tance. For the correct p art or information for a particu- lar SNAPPER mower , always mention the model and serial number .
15 Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BEL T 1. Lower deck to lowest setting. 2. Remove footrest. See Figure 4.3. 3. Removal of footrest will allow access to mower drive belt. 4. Check the belt tension. If belt is frayed, slit, sev- ered or belt strands exposed, replace belt before oper- ating mower .
16 Section 4 - MAINTENANCE 4.3.3. RIDING MOWER - LUBRICA TION 1. Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See Figure 4.5. 2. Hydro Pumps Check the level of the fluid in the fluid reservoir .
17 Section 4 - MAINTENANCE 4.5 ANNUALL Y (END OF EACH SEASON) (Continued from previous Page) 4.5.2. FUEL FIL TER Service fuel filter as instructed below . T urn key to "OFF" position. Engine MUST be stopped and MUST be cold before removing filter .
18 Section 4 - MAINTENANCE 4.6 DECK REMOV AL (Continued from previous p age) 4. Remove inside nuts that secure chain to front lift arm. See Figure 4.10. 5. Remove inside nuts that secure chain to rear lif t arm. See Figure 4.1 1. 6. Remove mower drive belt from around blade clutch pulley .
19 Section 5 - ADJUSTMENTS & REP AIR 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement and stopping of the machine. Move the control levers to the center or neutral position to stop machine. IMPORT ANT : Always return both motion control levers with hand assist ance to the neutral posi- tion.
20 Section 5 - ADJUSTMENTS & REP AIR 5.1 NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page) 12. With motion control levers remaining in the neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of rod.
21 Section 5 - ADJUSTMENTS & REP AIR 5.2.1. MOWER DECK ADJUSTMENT (LEVELNESS) SIDE to SIDE and FRONT to REAR 8. Move deck lift lever and set the mower deck to the highest cutting position and recheck side to side blade tip dimensions. The dif ference between the two should be 1/8" or less.
22 Section 5 - ADJUSTMENTS & REP AIR 5.3 TRACTION BEL T TENSION The traction drive belt tension does not require adjustment. If the belt is slipping, it will have to be replaced. 5.4 TRACTION BEL T REPLACEMENT 1. Remove mower drive belt from around clutch pul- ley .
23 Section 5 - ADJUSTMENTS & REP AIR 5.6a MOTION LEVER HANDLEBAR ALIGNMENT Handlebars of both left and right Motion Control Levers should be aligned when levers are dropped from their neutral lock positions. See Figure 5.12a. If bars are not aligned: 1.
24 Section 5 - ADJUSTMENTS & REP AIR 5.8 ENGINE ADJUSTMENTS & REP AIR Refer to the engine owner's manual for engine adjust- ments and/or rep airs. 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS 1. Inspect blade frequently for signs of excessive wear or damage.
25 Section 5 - ADJUSTMENTS & REP AIR 5.10 BA TTER Y 5.10.1. BA TTER Y REMOV AL 1. Remove battery retainer . See Figure 5.17. 2. Slide terminal cover away from positive terminal. 3. Observe and note cable positions on battery . Disconnect cables from battery terminals, disconnect- ing BLACK (Negative) cable first and RED (Positive) last.
26 Section 5 - ADJUSTMENTS & REP AIR 5.10.4. BA TTER Y TESTING 1. Remove battery . Refer to Section "BA TTERY REMOV AL". 2. Using a voltmeter , check the battery's state of charge by comparing the voltmeter reading with the chart below .
27 Section 5 - ADJUSTMENTS & REP AIR 5.1 1 HYDRAULIC SYSTEM, PURGING After replacing or rep airing hydraulic system compo- nents, one or both of the wheel drives may not pull properly .
28 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION St arter Will Not Crank Engine 1. Battery dead. 1. Service battery . 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Clean and check connections for good contact.
29 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Machine Will Not Move Loss Of T raction 1. Motion Control Levers in the neutral "N" position. 1. Move Motion Controls to desired speed position. 2. Hydro. Pumps in roll release setting.
30 SER VICE SCHEDULE ITEM SERVICE PERFORMED REF . NUMBER EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 9 X Initial Oil Change Page 14 X Periodic Oil Change Page 15 X.
31 2 YEAR LIMITED W ARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
32 PRIMAR Y MAINTENANCE.
33 PRIMAR Y MAINTENANCE.
34 PRIMAR Y MAINTENANCE.
35 PRIMAR Y MAINTENANCE.
36 SNAPPER PRODUCT REGISTRA TION FORM IMPOR T ANT : KEEP THIS INFORMA TION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper pur chase) Model Number________________________.
37 NOTES.
38 NOTES.
39 NOTES.
40 COPYRIGHT © 2005 SNAPPER - A DIVISION OF SIMPLICITY MFG ., INC. ALL RIGHTS RESER VED IMPORT ANT Snapper product s are built using engines that meet or exceed all applicable emissions requirement s on the date manufactured. The labels on those engines cont ain very import ant emissions information and critical safety warnings.
Een belangrijk punt na aankoop van elk apparaat Snapper HZT21481BV (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper HZT21481BV heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper HZT21481BV vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper HZT21481BV leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper HZT21481BV krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper HZT21481BV bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper HZT21481BV kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper HZT21481BV . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
