Gebruiksaanwijzing /service van het product RP217019BVE van de fabrikant Snapper
Ga naar pagina of 32
Safety Instructions & Operator’s Manual for 21” STEEL DECK RECYCLING WALK MOWERS SERIES 19 MODEL NUMBER EXPLANATION R P 21 70 19 B V E MODEL DESIGNATION ENGINE OPTION CUTTING WIDTH ENGINE DESIGNATION ENGINE HORSE POWER * SERIES DESIGNATION R – Recycling Model 60 – 6.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE (Continued From Previous Page) 3. DO NOT remove fuel cap or add fuel w ith the engine running.
4 IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE AND STORAGE (Continued From Previous Page) 9. Mow er blades are sharp and can cut. Wrap the blades or w ear heavy leather glov es and use CAUTION w hen handling them. 10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 2 - 4 TABLE OF CO NTENTS ...................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON.
6 Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operators of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices.
7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened.
8 Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2. 2. 1. EN GI NE & BLADE (Kaw asaki Engine) 1. Make sure fuel valve on engine is open. See Figure 2.5. FIGURE 2.5 2. Move engine speed control past “Fast” detent to “C ho ke ” position.
9 Section 2 - OPERATING INSTRUCTIONS 2. Set all wheels at the same cutting height. The highest cutting position is Notch 7. The lowest cutting position is Notch 1. See Figures 2.8 & 2.9. FIGURE 2.9 2.6 RECYCLING OPERATION NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.
10 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
11 Section 3 – MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.
12 Section 3 – MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
13 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
14 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
15 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
16 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
17 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
18 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
19 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
20 Section 4 - REPAIR & ADJUSTMENTS 4.5. BATTERY SERVICE 4.5.1. NEW BATTERY PREPARATION 1. Remove battery from carton. 2. Place battery in a well ventilated area on a level non-concrete surface. 3. Remove battery cell caps. Fill cells as required with electrolyte (supplied with battery) to proper level.
21 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty. 1. F ill fuel tank w ith fresh fuel. Using Recoil Starter 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for Instructions. 3.
22 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 7 X Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre.
23 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
24 PRIMARY MAINTENANCE.
25 PRIMARY MAINTENANCE.
26 PRIMARY MAINTENANCE.
27 PRIMARY MAINTENANCE.
28 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number ____________________________.
29 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
30 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
31 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
32 Safety Instructions & Operator’s Manual for 21” STEEL DECK RECYCLING WALK MOWERS SERIES 19 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
Een belangrijk punt na aankoop van elk apparaat Snapper RP217019BVE (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper RP217019BVE heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper RP217019BVE vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper RP217019BVE leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper RP217019BVE krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper RP217019BVE bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper RP217019BVE kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper RP217019BVE . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
