Gebruiksaanwijzing /service van het product S200KAV2561, S200XK2761 van de fabrikant Snapper
Ga naar pagina of 48
5101090 Revision 01 Rev . Date: 7/2007 TP 100-7332-01-M2-SP Briggs & Stratton Y ard Power Products Group 5375 North Main Street Munnsville, NY 13409 800-933-6175 S200X Series Zero-T urn Riding Mow.
W ARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects, or other reproductive harm. Thank you for pur chasing this quality-built Snapper Pro product. We’re pleased that you’ve placed your confidence in the Snapper Pro brand.
T able of Contents Operator Safety .....................................................2 Safety Rules and Information ...........................................2 Safety Decals ..................................................................11 Safety Interlock System .
2 www .SnapperPro.com Safety Operator Safety OPERA TING SAFETY Congratulations on purchasing a superior -quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety . Do not operate this machine unless you have been trained.
3 Safety Operator Safety SLOPE OPERA TION Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover .
4 www .SnapperPro.com Safety ROLL BAR USE Keep the roll bar in the raised position and fasten the seat belt. There is no roll over protection when the roll bar is down! Do not jump off if the mower tips (it is safer to be secured by the seat belt with the roll bar raised.
5 Safety Operator Safety ENCLOSED AREAS Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers. The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death.
6 www .SnapperPro.com Safety 2. Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards. 3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’ s position.
7 Safety Operator Safety spark arrester . It is a violation of California Public Resource Code Section 4442 to use or operate the engine on or near any forest-covered, brush-covered, or grass-covered land unless the exhaust system is equipped with a spark arrester meeting any applicable local or state laws.
8 www .SnapperPro.com Safety Operator Safety SERVICE AND MAINTENANCE T o avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
9 Safety Operator Safety 27. Models equipped with an engine radiator: WARNING: Stored energy device. T o prevent serious bodily injur y from hot coolant or steam blow-out, never attempt to remove the radiator cap while the engine is running. Stop the engine and wait until it is cool.
10 www .SnapperPro.com Safety INSPECT BUCKLE & LA TCH INSPECT WEBBING Operator Safety W ARNING Failure to properly inspect and maintain the seat belt can cause serious injury or death.
Safety Operator Safety 11 Safety Decals This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
12 www .SnapperPro.com Safety Operator Safety Safety Interlock System This unit is equipped with safety interlock switches. These safety systems are present for your safety , do not attempt to bypass safety switches, and never tamper with safety devices.
13 Safety Operator Safety Identification Numbers S S A A M M P P L L E E When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your part number , serial number and engine serial numbers in the space provided on the inside front cover for easy access.
14 www .SnapperPro.com Controls Control Functions The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. T o learn what combination and sequence of controls to use for various tasks see the OPERA TION section.
Fuel T ank Cap T o remove the cap, turn counterclockwise. Fuel Level Gauge Displays the fuel level in the tank. Features & Controls 15 Controls Parking Brake DISENGAGE Releases the parking brake. ENGAGE Locks the parking brake. Pull the parking brake lever back to engage the parking brake.
16 www .SnapperPro.com Operation General Operating Safety Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower . • Become familiar with all of the controls and how to stop the unit.
Operation 17 Operation Figure 4. Seat Adjustment A. Seat Adjustment Lever Seat Adjustment See Figure 4. The seat can be adjusted forward and backward. Move the lever towards the left, position the seat as desired, and release the lever to lock the seat into position.
18 www .SnapperPro.com Operation Figure 7. Raise & Lower the Roll Bar A. Hair Pin Clip B. Retainer Pin C. Roll Bar D. Rubber Stop Raise and Lower the Roll Bar T o Lower the Roll Bar: 1. Pull the hair pin clips (A, Figure 7) out of the retainer pins (B).
19 Operation Starting the Engine 1. While sitting in the operator’ s seat, engage the parking brake by pulling the parking brake lever back, make sure the PTO switch is disengaged (pressed down fully) and the motion control handles are locked in the NEUTRAL position.
Operation Zero T urn Driving Practice The lever controls of the Zero T urn rider are responsive, and learning to gain a smooth and efficient control of the rider’ s forward, reverse, and turning movements will take some practice.
Executing an End-Of-Row Zero T urn Y our Zero T urn Rider’ s unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and Y -turn before starting a new row . For example, to execute a left end-of row zero turn: 1.
22 www .SnapperPro.com Operation Mowing 1. Engage the parking brake. Make sure the PTO switch is disengaged, the motion control levers are locked in the NEUTRAL position and the operator is on the seat. 2. Start the engine (see Starting The Engine ). 3.
23 Operation When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: 1. Mow when the grass is between three and five inches high. 2. Mow with sharp blades.
Figure 18. T railer Weight Recommendations A. Clevis Pin B. Clip Attaching A T railer The maximum weight of a towed trailer should be less than 200 lbs (91kg). Secure the trailer with a appropriately sized clevis pin (A, Figure 18) and clip (B). Excessive towed loads can cause loss of traction and loss of control on slopes.
25 Maintenance Maintenance Schedule The following schedule should be followed for normal care of your rider and mower . Y ou will need to keep a record of your operating time. Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter .
26 www .SnapperPro.com Maintenance Checking / Adding Fuel T o add fuel: 1. Remove the fuel cap. 2. Fill the tank to about 1-1/2” (3,81 cm) of the bottom of the filler neck. This will allow for fuel expansion. NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations.
27 Maintenance Regular Maintenance Lubrication Lubricate the unit at the locations shown in Figures 20 through 23 as well as the following lubrication points. Grease: • front caster wheel axles & yokes • deck lift pivot blocks • mower deck spindles • mower deck idler arm Use grease fittings when present.
28 www .SnapperPro.com Maintenance Regular Maintenance Figure 25. Battery Compartment A. Hydraulic Oil Reservoir B. Hydraulic Oil Filter Figure 24. Checking Hydraulic Oil Level A. Hydraulic Oil Reservoir B. Reservoir Cap A B Check Hydraulic Oil Level 1.
29 Maintenance Regular Maintenance Servicing The Mower Blades Removing the Mower Blade 1. T o remove the mower blade, use a 1” wrench on the flats of the spindle shaft and remove the mower blade mounting bolt with a 15/16” wrench (Figure 26).
30 www .SnapperPro.com Maintenance Figure 31. Tightening the Mower Blade for Installation A. Mower Blade Mounting Bolt B. Flat Washer C. Mower Blade Air Lift (Points Up For Installation) D. 4 X 4 Wooden Block D A B Sharpening the Mower Blade 1. Sharpen the mower blades with grinder , hand file, or electric blade sharpener .
31 Maintenance Ground Speed Control Lever Adjustment The control levers can be adjusted in three ways. The alignment of the control levers, the placement of the levers (how close the ends are to one another) and the height of the levers can be adjusted.
32 www .SnapperPro.com 2" - 2-1/ 8 " (5,0 - 5,4cm) Figure 35. Parking Brake Adjustment A. Brake Spring B. Adjustment Nut Parking Brake Adjustment 1. Disengage the PTO, stop the engine, block the front wheels, remove the ignition key , and engage the parking brake.
33 Regular Maintenance Maintenance Figure 36. Neutral Return Spring Adjustment A. Set Collar B. Adjustment Linkage Rod C. Neutral Return Spring D. Neutral Return Bushing E. Spring Stop Plate Return-T o-Neutral Adjustment T o determine if it is necessar y to adjust the neutral return, perform the following steps.
34 www .SnapperPro.com Deck Rod Timing Adjustment 1. Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar); front tires to 25 psi (1,72 bar). 2. T o check the lift rod timing, measure and record the distance between the lift pivots and the rod pivots.
35 Regular Maintenance Maintenance Figure 42. Mower PTO Belt Routing A. Spindle Pulley B. PTO Drive Belt C. Spring-loaded Idler Pulley D. Stationary Idler Pulley B A Figure 41. Mower PTO Belt A. Idler Arm B. Stationary Idler Pulley B Mower Belt Replacement 1.
36 www .SnapperPro.com 8 3/8” (21,2 cm) Figure 43. Hydraulic Pump Drive Belt Replacement A. Pump Drive Belt B. Crankshaft Pulley C. Pump Pulley D. Idler Pulley E. Idler Arm F . Spring G. Spring Anchor Eyebolt B D A C F G E C Hydraulic Pump Drive Belt Replacement 1.
37 Regular Maintenance Maintenance Figure 44. Battery Compartment A. Positive (+) Cable & T erminal B. Negative (-) Cable & T erminal Battery Maintenance NOTE: This unit is equipped with a maintenance-free BCIU1 battery . Cleaning the Battery and Cables 1.
38 www .SnapperPro.com Battery Ser vice Checking Battery Voltage A voltmeter can be used to determine condition of battery . When engine is off, the voltmeter shows battery voltage, which should be 12 volts. When engine is running, the voltmeter shows voltage of charging circuit which normally is 13 to 14 volts.
39 Regular Maintenance Maintenance To Starter Switch Starting V ehic le Battery T o Ground To Starter Switch Dischar g ed V ehic le Battery Engine Block THIS HOOK-UP FOR NEGA TIVE GROUND VEHICLES MAKE.
40 www .SnapperPro.com Storage T emporar y Storage (30 Days Or Less) Remember , the fuel tank will still contain some gasoline, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation.
41 Maintenance T roubleshooting Chart While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be per formed to allow it to continue operating properly . The troubleshooting guide below lists the most common problems, their causes and remedies.
42 www .SnapperPro.com T roubleshooting Rider T roubleshooting Continued. Problem Cause Remedy Engine runs, but rider will 1. Hydraulic release valve(s) 1. T urn valve(s) clockwise to close. not drive. in “open” position. 2. Belt is broken. 2. See Drive Belt Replacement.
43 T roubleshooting T roubleshooting Common Cutting Problems Problem Cause Remedy Streaking. 1. Blades are not sharp. 1. Sharpen your blades. 2. Blades are worn down to far . 2. Replace your blades. 3. Engine speed is too slow . 3. Always mow at full throttle.
44 www .SnapperPro.com ENGINE: 25 HP Kawasaki Make Kawasaki Model FH721V Horsepower 25 @ 3600 rpm Displacement 41.2 Cu. in (675 cc) Electrical System 12 Volt, 13 amp. Alternator , Batter y: 340 CCA Oil Capacity 2.0 US qt. ( 1.9 L) w/ Filter 27 HP Kohler Make Kohler Model CV740S Horsepower 27 @ 3600 rpm Displacement 44.
Thank you f or purchasing Ferris commercial mowing equipment. Please take a f ew minutes to read this limited w arranty information. It contains all the information you will need to ha ve your F erris mower repaired in the unlikely e vent that a breakdo wn covered b y this limited warranty should occur .
Briggs & Stratton Y ard Power Products Group 5375 North Main Street Munnsville, NY 13409 800-933-6175 www .SnapperPro.com ENGINE: 25 HP Kawasaki Make Kawasaki Model FH721V Oil Capacity 2.0 US pt. ( 1.9 L) w/ Filter 27 HP Kohler Make Kohler Model CV740S Oil Capacity 2.
Een belangrijk punt na aankoop van elk apparaat Snapper S200KAV2561, S200XK2761 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper S200KAV2561, S200XK2761 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper S200KAV2561, S200XK2761 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper S200KAV2561, S200XK2761 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper S200KAV2561, S200XK2761 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper S200KAV2561, S200XK2761 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper S200KAV2561, S200XK2761 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper S200KAV2561, S200XK2761 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
