Gebruiksaanwijzing /service van het product SGV13320KW van de fabrikant Snapper
Ga naar pagina of 32
GVTP SM32-R0303.1 ASSEMBLY INSTRUCTIONS OPERATOR’S MANUAL PARTS LIST Walk-Behind Mower 32” cut model Actual product may differ slightl y from product pictured above Models covered: SGV13320KW.
GVTP SM32-R0303.1 This pa ge inten tionally bl ank.
GVTP SM32-R0303.1 1 preliminaries Congratulations! You have just purchased one of the finest pieces of out door power equipment on the market today. If properly cared for, your new mower will provide years of dependabl e service. Please read and follow this instruction manual carefully in order to get the most out of your new equipment.
GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment PLEASE READ THE FOLLOWING BEFORE ASSEMBLING OR OPERATING UNIT TRAINING • Read, understand, and follow all instructions in the manual and on the unit before starting.
GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment (cont.) SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope, or if you feel uneasy on it, do not drive on it.
GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment (cont.) • Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary.
GVTP SM32-R0303.1 3 unit assembly (cont.) DISCHARGE DEFLECTOR ASSEMBLY • Attach discharge deflector (1:5) using two 5/16" x ¾ " bolts and lock nuts (1:6-7).
GVTP SM32-R0303.1 3 unit assembly (cont.) TRANSMISSION SHIFT LEVER ASSEMBLY (cont.) • Position ‘double-D’ hole in bottom leg of shift lever onto transmission stud, then slowly move handle of shifter back and forth until hole drops onto matching base of stud.
GVTP SM32-R0303.1 3 unit assembly (cont.) HANDLE ASSEMBLY INSTALLATION • Install handle assembly (4:1) to upper portion of engine deck using four 1/2" x 1-1/4" hex bolts and serrated flange nuts (4:3-4). Adjust for comfortable operation, then tighten securely.
GVTP SM32-R0303.1 4 unit operation STARTING THE ENGINE IMPORTANT NOTE: The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer’ s oper ating instructions. In order to obtain optimum performance from your engine, refer to your engine manual.
GVTP SM32-R0303.1 4 unit operation (cont.) STARTING THE ENGINE (cont.) • Grasp recoil handle and pull briskly. You may have to pull several times before engine starts. (If engine fails to start within a reasonable amount of time, discontinue and check engine manual for further instructions.
GVTP SM32-R0303.1 4 unit operation (cont.) • Learn to listen to your machine – being aware of w hat a well-running unit sounds like can alert you to a potential problem. A straining engine or clanging blades or a slapping belt mean that trouble is almost sure to follow.
GVTP SM32-R0303.1 4 unit operation (cont.) • Move the shift lever to first gear (‘1’), unlock brakes, and slowly release the brake handles. • Your mower has five forward speeds (‘1’ – ‘5’); simply slide the shifter lever to the appropriate indicator position to select that gear.
GVTP SM32-R0303.1 5 maintenance GENERAL: • Follow implicitly the engine manufacturer’s recommendations for maintenance. • Always keep your machine clean - especially the engi ne deck. Check all adjustments periodically. Also, periodically check that all fasteners are secure.
GVTP SM32-R0303.1 5 maintenance (cont.) TROUBLESHOOTING: • UNIT WILL NOT START: Check to make sure cutting blades are disengaged. Check to make sure transmission is in neutral. Check fuel and oil levels. Check to make sure throttle control engages engine choke when set to ‘start’ position; adjust if needed.
GVTP SM32-R0303.1 5 maintenance (cont.) • THROTTLE/CHOKE CABLE ADJUSTMENT: Correct throttle cable adjustment allows for full range of motion on engine throttle body in conjunction with throttle control on handle dash. Correct choke cable adjustment engages choke when choke knob is pulled fully out.
GVTP SM32-R0303.1 5 maintenance (cont.) • BRAKE ADJUSTMENT: LOWER ROD - The brake assembly has been set at the factory. However, they may periodically need adjustment. As a rule of thumb, the bottom bend of the lower brake rod (3:14) should be 3/8” lower than the center of the pivot boss hole in the brake arm (3:5).
GVTP SM32-R0303.1 5 maintenance (cont.) • SIDE IDLER TENSION SPRING ADJUSTMENT: To increase tension, remove nut and lock washer securing rear spring hanger bolt (3:34) in middle tension hole, and replace bolt in uppermost hole. To decrease tension, replace in lowest hole.
GVTP SM32-R0303.1 19 18 23 24 32" Cut Mower BLADE DECK GROUP SHEET 1 OF 4 R0303.1 15 12 12 13 15 14 16 41 5 10 9 8 11 17 21 26 6 7 25 20 A 29 A thru 44 22 32 27 31 30 25 28 34 33 31 40 36 35 43 3.
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 1 - BLADE DECK GROUP REF # PART # QTY DESCRIPTION 1 3010260 1 Blade deck --- 3079166 1 Decal – ‘Operating Rules 1-8’ --- 3079090 2 Decal .
GVTP SM32-R0303.1 34 3031987 1 3/8-16 small serrated flange nut Snapper 32” Cut Mower R0303.1 SHEET 1 - BLADE DECK GROUP (cont.) REF # PART # QTY DESCRIPTION 35 3031410 1 3/8-16 x 2" carriage b.
GVTP SM32-R0303.1 14 29 To Driv e Wheel - See Side Idler & Axle Gro up 32" Cut Mower ENGINE & TRANS GROUP SHEE T 2 OF 4 R0303.1 To Blade Pulleys - See Blade Deck Gr oup 13 12 11 10 To Re .
GVTP SM32-R0303.1 Snapper 32” Cut Mower SHEET 2 - ENGINE & TRANS GROUP REF # PART # QTY DESCRIPTION (no model designation denotes common) 1 3010261 1 Engine base --- 3027503 1 Blade cam cover pl.
GVTP SM32-R0303.1 Snapper 32” Cut Mower SHEET 2 - ENGINE & TRANS GROUP (cont.) REF # PART # QTY DESCRIPTION 41 3023182 3 1/2" oillite washer 42 3031637 1 1/2-13 nylon lock nut 43 3031915 1 .
GVTP SM32-R0303.1 1 32" Cut Mower SIDE IDLER & AXLE GROUP SHEET 3 OF 4 R0303.1 13 32 23 10 4 3 2 24 11 thru 20 18 17 15 14 9 8 A 28 26 25 27 19 16 12 7 6 5 See Engine & Trans Group 33 31 .
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 3 - SIDE IDLER & AXLE GROUP REF # PART # QTY DESCRIPTION 1 3033231 1 Axle assembly 2 3027407 1 Brake pivot plate - left --- 3027408 1 Brake .
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 3 - SIDE IDLER & AXLE GROUP (cont.) REF # PART # QTY DESCRIPTION 38 3027511 1 Wheel drive pulley cover – left --- 3027512 1 Wheel drive pu.
GVTP SM32-R0303.1 32 14 See Engine & Tra ns Group See Side Id ler & Axle Group 25 35 34 36 4 Cable goes thru #3 4 this page 1 16 30 32" Cut Mower HANDLE GR OUP SHEET 4 OF 4 R0303.
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 4 - HANDLE GROUP REF # PART # QTY DESCRIPTION 1 3023511 1 Handle assembly --- 3032136 1 Mower dash overlay decal 2 3031283 2 Handle grip - 1&quo.
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 4 - HANDLE GROUP REF # PART # QTY DESCRIPTION --- 3031916 1 5” jumper wire – 1/4” female spade to bullet terminal – engine kill --- 3031.
GVTP SM32-R0303.1 32" Cut Mower HARNESS W IRING SCHEME 2-terminal male h ousing - Blade Clutch A - Not use d B - To 1/4" Female on Har ne ss C - To Ground le ad D-F - Not U se d G-H - To 2-t.
GVTP SM32-R0303.1 McDonough, GA 30253 U.S.A..
Een belangrijk punt na aankoop van elk apparaat Snapper SGV13320KW (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper SGV13320KW heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper SGV13320KW vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper SGV13320KW leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper SGV13320KW krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper SGV13320KW bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper SGV13320KW kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper SGV13320KW . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
