Gebruiksaanwijzing /service van het product SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 van de fabrikant Snapper
Ga naar pagina of 37
Safety Instructions & Operator’s Manual for PRO HYDRO WALK BEHIND MOWERS MID-SIZE SERIES 3 POWER UNIT MOD EL S MOWER UNIT MOD EL S SPLH153KW SPLH173KW SPA361 SPA481 SPA521 SPA611 MODEL NUMBER EX.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 10. Protect yourself when mow ing and wear appropriate clothing including safety glasses, long pants, ear protection, hardhat and substantial footw ear with good traction. Long hair, loose clothing or jewelry may get tangled in mov ing parts.
IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE 1. Shut off fuel while storing or transporting. DO NOT store machine or fuel container inside w here fumes may reach an open flame, spark or pilot light such as in a w ater heater, furnace, clothes dry er or other gas appliance.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS .................................................................................. 2-4 TABLE OF CONTEN TS ................................................................................................
SECTION 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER PRO HYDRO WALK BEHIND MOWER. It’s purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices.
SECTION 2 – SAFETY MESSAGES AND SYMBOLS ! IMPORTANT SAFETY AND OPERATING INSTRUCTIONS ! READ, UNDERSTAND AND FOLLOW IN STRUCTIONS AND WARNINGS IN THIS MANUAL, AND ON THE MACHINE, ENGINE AND ATTACHMENTS.
SECTION 2 – SAFETY MESSAGES AND SYMBOLS RIGHT TRA CTION LEVER S Q UEEZE FOR RIGHT TURN FORWARD FAST SLOW SPEED RANGE SETTING ENGINE SPEED CONTROL FAST SLOW SPEED RANGE SETTING LEFT TRACTIO N LEVER S.
SECTION 2 – SAFETY MESSAGES AND SYMBOLS DANGER! ROTATING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA DANGER! ROTATING BLADES ENGINE AND COMPONENTS ARE HOT.
SECTION 2 - CONTROLS Before operating, become familiar with all the controls (See Figure 2.1A) and how to use them. Know beforehand how to STOP the Right Hand and Left Hand Traction Wheel Drives, the Mow er Blades, and the Engine in preparation for a possible emergency.
SECTION 3 - OPERATING INSTRUCTIONS WARNING DO NOT allow operation of the machine by untrained personnel. 3.1 PRE-START CHECKLIST Make the following checks and perform the services as required before each start-up.
SECTION 3 - OPERATING INSTRUCTIONS 3.3 STOPPING IMPORTANT : Squeezing both Traction Levers back past Neutral position will cause the machine to back up. 1. Squeeze both Traction Controls simultaneously towards handle bar until both are in Neutral. Manually engage the Neutral Latch.
SECTION 3 - OPERATING INSTRUCTIONS WARNING The SNAPPER Pro Hydro Mowers have a Transport Speed, w hich allows the machine to travel forw ard at a speed of 6 MPH - it is NOT to be used while w alking! .
SECTION 3 - OPERATING INSTRUCTIONS 3.6 MOWER OPERATION (Continued from Previous Page) 5. While holding both Traction Levers in the neutral position, release the Neutral Latch by squeezing both Traction Levers slightly rearward. 6. Simultaneously (and slowly), release both Traction Levers.
SECTION 3 - OPERATING INSTRUCTIONS 3.8 HANDLE HEIGHT ADJUSTMENT (Continued from previous page) STEP 3: Insert rod (5/16” diameter x 20” long) through alignment holes in the left and right traction control shift lever arms and the tank support bracket.
SECTION 3 - OPERATING INSTRUCTIONS 3.9 CUTTING HEIGHT ADJUSTMENT (Fixed Decks) The Mower has three methods of adjusting cutting height listed as follows: 1. Moving pos ition of BLADE on cutter spindle shaft. 2. Moving position of CASTER WHEEL on support.
SECTION 3 - OPERATING INSTRUCTIONS 3 . 1 2 ADJUSTING FIXED DECK ATTACHMENT The Mower Deck has four different positions for attaching it to the power unit.
SECTION 4 - ENGINE TROUBLESHOOTING SYMPTOM PROBLEM SOLUTION PAGE Engine Key OFF. Turn Key to Run. 12 does not Fuel Tank empty. Fill Fuel Tank. 11 start.. Fuel Shut-Off Closed. Open Fuel Shut-Off. 12 Engine Throttle Control not at FAST Put Engine Throttle Control to FAST (Rabbit) 12 (Rabbit) position.
SECTION 4 - SERVICE & LUBRICATION INFORMATION FIGURE 4.1 TRAC TION LEVERS Lubricate each with 1-2 shots of grease every 25 hours of operation. INTERLOCK SWITCHES Inspect switches for ease of operation. HYDRAULIC OIL Use SAE 10W-30 Oil. HYDRAULIC FILTER Change Hydraulic Oil and Filter after first 25 hours of operation.
SECTION 4 - SERVICE & LUBRICATION INFORMATION HOURS PROCEDURE COMMENTS BREAK-IN Check all fasteners for proper tightness Change Engine Oil and Filter at 5 hours ..............................S ee engine manual Change Hydraulic Oil and Filter at 25 hours .
SECTION 4 – SERVICE WARNING Once blades are disengaged, they should come to a complete stop in 7 seconds or less. If the blades continue to rotate after 7 seconds, the electric clutch must be checked. Replacement of electric clutch may be necessary .
SECTION 4 - SERVICE 4 . 2 . 3 . HYDRAULIC PUMP BELT REMOVAL (Continued) 2. Loosen Nut on Belt Guide at rear of Engine Pulley and remove Cutter Deck Belt from Engine Pulley. 3. Remove Hydraulic Pump Belt. 4.2.4. HYDRAULIC PUMP BELT INSTALLATION 1. STOP ENGINE! Place Hydraulic Belt on Engine and Pump Pulleys.
SECTION 4 - SERVICE 4.4 TRACTION CONTROL NEUTRAL ADJUSTMENT The Traction Control Neutral Adjustment procedure is sensitive. The following steps and WARNINGS must be followed very carefully. WARNING Several steps of the Neutral Adjustment procedure require that the engine be started.
SECTION 5 - MOWER ATTACHMENT SERVICE 5.1 CUTTER DECK BELT REMOVAL & INSTALLATION 5.1.1. 36” CUTTING DECK BELT REMOVAL 1. Move Mower onto a smooth, level surface. Turn Ignition Key to STOP position, remove Key, disconnect Spark Plug Wire and secure Wire away from Spark Plug.
SECTION 5 - MOWER ATTACHMENT SERVICE 5 . 1 . 5 . SPINDLE TO SPINDLE DECK BELT INSTALLATION - 48”, 52”, & 61” CUTTING DECKS 1. Route new belt for 48” cutting deck, 52” cutting deck, and 61” cutting decks, onto bottom groove of center Spindle Pulley and left hand Spindle Pulley.
SECTION 5 - MOWER ATTACHMENT SERVICE 5.3 MOWER SPINDLES (Field Serviceable Spindles) BEARING REPLACEMENT In the event that a spindle bearing requires replacement, the SNAPPER Field Serviceable Spindles have been designed so that no special tools or presses are required.
SECTION 6 - BATTERY SERVICE & TESTING WARNING Shield the positive terminal w ith terminal cover located on battery harness. This prevents metal from touching the positive terminal, w hich could cause sparks. Cables must be connected to battery terminals in the proper position.
SECTION 6 - BATTERY SERVICE & TESTING 6.5 NEW BATTERY PREPARATION 1. Remove battery from carton. 2. Place battery in a well ventilated area on a level non- concrete surface. 3. Remove battery cell caps. Fill cells as required with electrolyte (purchased separ ately) to proper level.
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number _______________________________.
PRIMARY MAINTENANCE 31.
PRIMARY MAINTENANCE 32.
PRIMARY MAINTENANCE 33.
PRIMARY MAINTENANCE 34.
SERVICE NOTES ______________________________________________________________________________ ______________________________________________________________________________ ____________________________.
SERVICE NOTES ______________________________________________________________________________ ______________________________________________________________________________ ____________________________.
Safety Instructions & Operator’s Manual for PRO HYDRO MID-SIZE WALK BEHIND MOWERS SERIES 3 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
Een belangrijk punt na aankoop van elk apparaat Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper SPLH153KW, SPLH173KW, SPA361, SPA481, SPA521, SPA611 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
