Gebruiksaanwijzing /service van het product ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M van de fabrikant Snapper
Ga naar pagina of 28
Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 POWER UNIT MODELS ZF2200K ZF2500K ZF2500KH MOWER UNIT MODELS ZF5200M ZF6100M MODEL NUMBER EXPLA NA.
2 IMPORTA NT SA FETY INSTRUCTIONS WARNING: This powerfu l cutting mach ine is capable of amput ating hands and f eet and can throw objects that can cause in jury and damage! Failure to comply wi th the follo wing SAFETY inst ructions coul d result in serious injury or death to the ope rator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS PREPA RA TION (Continued From Pre vious Page) 5. Practice operatio n of machine w ith BLA DES OFF to learn controls and develop skills. 6. Check th e area to be mowed and remo ve all objects such as toys, wire, rocks, limbs and other objects that could cau se injury if thrown by blades or interfere with mowing.
4 TABLE OF CONTENTS SECTION 1 - IMPORTA NT SA FETY INSTRUCTIONS .......................... 2-3 TA BLE OF CO NTENTS ............................................................................ 4 SECTION 1 – FA MILIA RIZA TION ........................
5 Section 1 - FA MILIA RIZA TION FIGURE 1.1 1. 1 INT RODUCTION This manual has been prepar ed for the operator’s of the SNAPPER O UT FR ONT Z-R IDER. Its purpose, as ide from recom mending s tandard operating procedures and routine s ervice requirem ents, is to prom ote SAFET Y through the use of accepted oper ating practices.
6 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-STA RT CHECK LIST Make the following chec ks and perf orm the service required bef ore each start-up. 2.1.1. Check tires and add or releas e air as needed to bring pressure in dr ive tires to: 12 psi (T urf T y pe Tires ), 5 psi ( All Terr ain Type Tires) and 25 ps i in rear caster tire.
7 Section 2 - OPERA TING INSTRUCTIONS 2.2 STA RT ING & STOPPING – ENGINE, BLA DES & PA RKING BRA KE This mac hine is equipped with dual hy dros tatic wheel drive transm issions. Each trans mission is controlled by a single motion c ontrol lever or joystick.
8 Section 2 - OPERA TING INSTRUCTIONS 2.2. STO PPING ENGINE 2.2.1. ENGINE 1. Stop engine by turning k ey to the “OFF” position. Move engine speed control to turtle “SLOW ” position and key to “STOP” position. See Figure 2.6. WA RNING DO NOT leave machine with engine running.
9 Section 2 - OPERA TING INSTRUCTIONS 2.3 OPERA TION – M OTION CONT ROL 2.3.1 DRIVING MACHINE IMPO RTA NT : The joystick lever has to be m anually mo ved to propel machine. Always return the j oy stick with hand assistance to the neutral pos ition to stop ma chine.
10 Section 3 – MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the SN APPER Out Front Z- Rider, use genuine SNAPPER replacem ent parts only . Contact a loc al SNAPPER dealer for parts and service assistance. For the correct part or inform ation for a par ticular SNAPPER Out Front Z- Rider, alway s m ention the model and serial number.
11 Section 3 – MA INTENA NCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest s etting. b. Rem ove four knobs that s ecure the deck cover. See Figure 3.3. c. Remove cover to gain ac c es s to deck belt. FIGURE 3.3 2.
12 Section 3 - MA INTENA NCE 3.3.3. RIDING MOWER - LUBRICATION 1. Front & Rear Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, f rom a gr ease gun. See Figure 3.5. FIGURE 3.5 2. Transaxle Check the level of fluid in both of the fluid reservoir s.
13 Section 3 – MA INTENA NCE 3.5 A NNUALLY (END OF EA CH SEA SON) (Continued from previous P age) 3.5.2. FUEL FIL TER Service f uel filter as instr ucted below. Turn k ey to “OFF ” pos ition. Engine MUST be stopped and MUST be cold befor e removing f ilter.
14 Section 4 - A DJUSTMENTS & REPA IR DA NGER Exercise EXT REME CAUTION w hen making this adjustment, due to clos e proximity of moving parts. 4.1 NEUTRA L POSITION ADJUS T MENTS The j oy stick controls the movem ent and stopping of the mac hine. Move the joy stic k to the center or neutral position to stop m achine.
15 Section 4 - A DJUSTMENTS & REPA IR 4.2.1. M OWER DECK A DJUSTM ENT (Continued) 7. Turn ball joint in or out until ball joint anchor hole aligns with mounting hole. Reinstall bolt and tighten s ecurely . Us e sam e procedure on other cas ter w heel.
16 Section 4 - A DJUSTMENTS & REPA IR 4.5 MOW ER BLA DE REPAIR/REPLA CEM ENT 4.5.1. BLA DE WEAR LIMIT S 1. Inspect blade frequently for signs of excess ive wear or damage. See Figure 4.5. FIGURE 4.5 WA RNING DO NOT use a cut ting blade that sh ows signs of excessive w ear or d amage.
17 Section 4 - A DJUSTMENTS & REPA IR 4.6.2. ENG INE BELT REPLACEMENT 1. Route belt around blade pulleys and idler pulley in sam e the position as old belt was rem oved. It may be necessary to use a pry bar to pull idler pulley back to ins tall belt.
18 Section 4 - A DJUSTMENTS & REPA IR 4.7.4. BA T TERY TEST ING There ar e two ty pes of battery tests : Unloaded and Loaded. T he unloaded tes t is the procedure that will be disc us sed. It’s the sim plest and mos t comm only used. An unloaded test is m ade on a battery w ithout discharging current.
19 Section 4 - A DJUSTMENTS & REPA IR 4.8 MO WER SPINDLES (Field Serviceable Spindles) BEA RING REPLACEMENT In the event that a spindle bearing requir es replacem ent, the SNAPPER Field Serviceable Spindles have been designed so that no special tools or pres ses are required.
20 TROUBLESHOOTING PROBL EM PROBA BLE CA USE CORRECTIVE A CTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact.
21 TROUBLESHOOTING PROBLEM PROBA BLE CA USE CORRECTIVE A CTION Tractor Will Not Move Or 1. Joystick in the neutral “N” position. 1. Place joystick in desired speed position. Loss Of Traction 2. Ro ll r el e as e lever is in “ RO LL ” po s it io n .
22 SERVICE SCHEDULE ITEM SERVICE PERFO RMED REF. EA CH USE 5 HRS 25 HRS 50 HRS 100 HRS EA CH SEA SON Engine Oil Check Oil Level Page 6 X Initial Oil Change Page 10 X Periodic Oil Change Page 11 X* A ir Pre-Cleaner Clean Sponge Elem ent Engine Manual X** A ir Cleaner Clean or Replace Engine Manual.
23 2 YEA R LIMITED WARRA NTY For two (2) y ear s from purchase date f or the original purchaser 's use, SNA PPER , thr ough any author iz ed SNA PPER dealer will replace, f ree of charge ( except.
24 PRIMA RY MA INTENA NCE.
25 PRIMA RY MA INTENA NCE.
26 PRIMA RY MA INTENA NCE.
27 PRIMA RY MA INTENA NCE.
28 Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 IMPORTANT Snapper products are built using engines that meet or exceed all a pplicable emissions requirements on the date manufactured. The labels on thos e engines contain very important emissions infor mation and critical safety warnings.
Een belangrijk punt na aankoop van elk apparaat Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
