Gebruiksaanwijzing /service van het product ZM5200M, ZM2501KH, ZM6100M van de fabrikant Snapper
Ga naar pagina of 32
Safety Instructions & Operator’s Manual for MID M OUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 POWER UNIT MODELS ZM2501KH MOWER UNIT MODELS ZM5200M ZM6100M MODEL NUMB ER EXPLA NA TION Z M 25 0.
2 IMPORTA NT SA FETY INSTRUCTIONS WARNING: This pow erful cut ting machin e is capable of ampu tating han ds and feet an d can t hrow object s that can cause injury and damag e! Failure to comply wit h the follo wing SA FET Y instruct ions could result in serio us injury or death to the operator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS PREPA RATION (Continued From Pre vious Page) 5. Practice op eration of mach ine w ith BL A DES OFF to learn controls and develop skills.
4 TABLE OF CONTENTS SECTION 1 - IMPORTA NT SA FETY INSTRUCTIONS .......................... 2-3 TA BLE OF CONTENTS ............................................................................ 4 SECTION 1 – FA MILIA RIZAT ION .........................
5 Section 1 - FA MILIA RIZA TION FIGURE 1.1 1. 1 INTRODUCT ION This manual has been prepar ed for the oper ator’s of the SNAPPER MID MOUNT Z -RIDER. Its pur pose, as ide from rec omm ending s tandard operating procedur es and routine servic e requirem ents, is to prom ote SAFET Y through the use of accepted operating practices .
6 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the f ollowing check s and per form the servic e required bef ore each star t-up. 2.1.1. Check tires and add or r elease air as needed to bring pressure to 12 ps i in drive tires. Pr essure in front dec k c aster wheels should be 25 ps i.
7 Section 2 - OPERA TING INSTRUCTIONS 2.2 STARTING & STOPPING – ENGINE, BLA DES, PA RKING BRA KE This mac hine is equipped with dual hydrostatic wheel drive trans m issions. Each tr ansm ission is controlled by a single motion control lever or joystick.
8 Section 2 - OPERA TING INSTRUCTIONS 2.2.5. PA RKING BRA KE 1. Engage parking brak e by pulling the park ing brak e lever back to the engaged position.
9 Section 2 - OPERA TING INSTRUCTIONS 2.3 CUTT ING HEIGHT ADJUSTMENT 1. Adjust c utting height as desired to any position, using deck lift lever . See Figure 2.8. NOTE: T he engine does not have to be running to adj ust cutting height. FIGURE 2.8 2.4 OPERA TION- M OT ION CONTROLS 2.
10 Section 3 - MA INTENA NCE 3.1 INTRODUCT ION To re tain the quality of the SNAPPER m ower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer f or parts and service assis tance. For the correct part or inf orm ation for a particular SNAPPER mo wer, alway s m ention the m odel and serial number .
11 Section 3 - MA INTENA NCE 3.2.3. CHECK MOW ER DRIVE BELT 1. Foot Rest Removal a. Lower deck to lowest s etting. b. Remove f oot rest. See F igure 3.3. c. Rem oval of f oot rest will allow access to deck belt. FIGURE 3.3 2. Checking Belt T ension The idler and s pring provide proper belt tension and require no adj ustm ent.
12 Section 3 - MA INTENA NCE 3.3.3. RIDING MOWER - LUBRICATION 1. F ront Wh eel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, fr om a gr ease gun. See Figure 3.5. FIGURE 3.5 2. Transaxle Check the level of f luid in both of the f luid reservoir s.
13 Section 3 - MA INTENA NCE 3.5 A NNUA LLY (END OF EACH SEA SON) (Continued from previous P age) 3.5.2. FUEL FILT ER Service f uel filter as instructed below. T urn k ey to “OFF ” position. Engine MUST be stopped and MUST be cold befor e rem oving filter.
14 Section 3 - MA INTENA NCE 3.6 DECK REM OVA L (Continued from previous page) 5. Remove shoulder bolts, washers and nuts f rom rear lif t arm . See Figure 3.11. FIGURE 3.11 6. Disconnec t pull bar from f ront ax le by rem oving clevis pins and c otter pins.
15 Section 4 - A DJUSTMENTS & REPA IR DA NGER Exercise EXTREM E CA UT ION w hen makin g this adjustment, due to clos e proximity of moving parts. 4.1 NEUTRAL POSITIO N A DJUST M ENTS The joystick contr ols the movem ent and stopping of the machine.
16 Section 4 - A DJUSTMENTS & REPA IR 4.2 .1. MOWER D ECK A DJUS TM ENT (LEVELNESS) (Continued) 6. Loosen the nuts and bolts that secure both front and rear deck support brac kets on the high side of dec k. Loc ated above eac h suppor t brack et, on the top part of the power unit fram e, are thr ee shim plates.
17 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attempt ing any adjustment s, maintenance, service, or repairs, stop engine an d blade, alw ays remove key from ignit ion sw itch, remov e spark p lug wire( s) and secure w ire(s) aw ay from spark p lug(s).
18 Section 4 - A DJUSTMENTS & REPA IR 4.5.2. BLA DE SHA RPENING 1. Remove blade. See F igure 4.5. FIGURE 4.5 2. Inspect condition of blade. See Figure 4.4. 3. If blade is in good c ondition, sharpen at 22 to 28 degrees. DO NO T shar pen beyond existing cutting edge.
19 Section 4 - A DJUSTMENTS & REPA IR WA RNING Shield the positive terminal w ith terminal cover located on battery harness. T his preven ts metal f rom touching the positive termina l which could cause sparks. Cables must b e connected t o battery terminals in the proper position.
20 Section 4 - A DJUSTMENTS & REPA IR Batter y Condition Chart State of Charge Syr inge Hydrometer Digital Voltmeter Five Ball Hydrometer 100% Charged w/ Sulfate Stop 1.280 12.80v Five Balls Floating 100% Charged 1.265 12.60v Four Balls Floating 75% Charged 1.
21 TROUBLESHOOTING PROBLEM PROBA BLE CA USE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact.
22 TROUBLESHOOTING PROBLEM PROBA BLE CA USE CORRECTIVE ACTION Tractor Will Not Move 1. Joystick in the neutral “N” position. 1. Place joystick in desired speed position. Loss Of Traction 2. R o ll r e le a s e lever is in “R O LL ” p os i t i o n.
23 SERVICE SCHEDULE ITEM SERVICE PERFO RMED REF. EA CH USE 5 HRS 25 HRS 50 HRS 100 HRS EA CH SEA SON Engine Oil Check Oil Level Page 6 X Initial Oil Change Page 10 X Periodic Oil Change Page 11 X* A ir Pre-Cleaner Clean Sponge Element Engine Manual & Page 11.
24 2 YEAR LIMITED WA RRANTY For two (2) years from purc hase date for the or iginal purchaser 's use, SNA PPER , thr ough any author ized SNA PPER dealer will replac e, free of charge (ex cept fo.
25 PRIMA RY MA INTENA NCE.
26 PRIMA RY MA INTENA NCE.
27 PRIMA RY MA INTENA NCE.
28 PRIMA RY MA INTENA NCE.
29 NOTES.
30 NOTES.
31 NOTES.
32 Safety Instructions & Operator’s Manual for M ID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactur ed. The labels on those engines conta in very important emis sions information and critical safety warnings.
Een belangrijk punt na aankoop van elk apparaat Snapper ZM5200M, ZM2501KH, ZM6100M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper ZM5200M, ZM2501KH, ZM6100M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper ZM5200M, ZM2501KH, ZM6100M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper ZM5200M, ZM2501KH, ZM6100M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper ZM5200M, ZM2501KH, ZM6100M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper ZM5200M, ZM2501KH, ZM6100M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper ZM5200M, ZM2501KH, ZM6100M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper ZM5200M, ZM2501KH, ZM6100M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
