Gebruiksaanwijzing /service van het product UNO-2170 van de fabrikant B&B Electronics
Ga naar pagina of 40
UNO-2170 Celeron M Universal Network Controller with PC/104 ex tension User Manual.
Copyright This document is copyrighted, © 2004. All rights are reserved. The origi- nal manufacturer reserves the righ t to make improvements to the products described in this manual at any time without notice.
Product W arranty Advantech warrants to you, the original purchaser , that each of its products will be free from defects in materials and workmans hip for one year from the date of purchase.
UNO-21 70 User Manual iv.
Contents Chapter 1 Overview ....... ....................................................2 1.1 Introduction ....................................................................... 2 1.2 Hardware Specifications ... .. .... ... ... ... ..... .. .... ... .
Figure 3.1:Chassis Groundi ng Connection ................... 18 3.3 Connecting Power ........ ........ .............. ............ ........... ...... 19 3.4 Installing a Hard Disk ....... ......... ........... ........... ............ ... 19 3.5 BIOS Setup and System Assignments .
1 2 Overview This chapter provides an overview of UNO-2170s specifications. Sections include: • Introduction • Hardware specification • Safety precautions • Chassis dimensions.
Chapter 1 Overview 1.1 Introduction UNO-2170 is an embedded Application Ready Platform (ARP) that can shorten your development time and of fers rich networking interfaces to fulfill extensive needs in diff erent projects. Advantech Universal Net- work Controller is designed to be a total solution for network enabled Application Ready Platforms.
1.2 Hardware Specifications CPU: Up to Celeron-M 1GHz Ultra low- voltage version Memory: 256/512 MB D DR on board (Default: 256 MB DDR). Battery-backup RAM: 512 KB Battery-backup RAM VGA/Keyb oard/Mouse: DB-15 VGA Connector , PS/2 keyboard and mous e Serial Ports: 2 x RS-232 and 2 x RS-232/422/485 with DB-9 connectors.
1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. Wa rning! Always disconnect the power cord from your chassis wheneve r you ar e wor kin g on it. Do not connect while the power is on.
1.4 Chassis Dimension s Figure 1.1: Chas sis Dimensio ns 5 Chapter 1.
UN O- 21 70 U se r M an ual 6.
2 2 Hardware Functionality This chapter shows how to setup the UNO-2170s hardware functions, including connecting peripherals, setting switches and indicators.
Chapter 2 Hardwa re Functionality 2.1 Introduction The following two figures show the connectors on UNO-2170. The following sections give you detailed information about function of each periph eral. Figure 2.1: Fr ont panel of UNO-2170 Figure 2.2: Re ar panel of UNO-2170 2.
2.3 RS-232/422/485 Inte rface (CO M3~COM4) The UNO-2170 offers two RS-232/422/485 serial communication interface ports: COM3 and COM4. Please refer to Appendix A.
2.3.5 RS-232 /422/4 85 Selecti on COM3 and COM4 support 9-wire RS-232, RS-422 and RS-485 inter faces. The system detects RS-422 or RS-485 signals automatically in RS- 422/48 5 mod e. T o select between RS-422/485 and RS-232 for COM3, adjust JP4. T o select between RS-422/485 and RS-232 for COM4, adjust JP5.
2.3.6 RS- 485 Auto Flow Cont rol Mode and RS-422 Master/ Slave Mode Selection Y ou can set the “Auto Flow Control mode of RS-485 or “Master/Slave ＂ mode of RS-422 by using the SW3 DIP switch for each RS-422/485 port.
2.3.7 IRQ and Addres s Sett ing The IRQ and I/O address range of COM3 and COM4 are listed below: COM3: 3E8H, IRQ10 (Independent IRQ), IRQ10 (Share IRQ) COM4: 2E8H, IRQ5 (I ndependent IRQ), IRQ10 (Share IRQ) V ector address for share IRQ: 1D0H Yo u can set “Share IRQ ＂ or “Independent IRQ ＂ by the first switch of SW4.
2.4 LAN: Ethernet Connector The UNO-2170 is equipped with a Realtek R TL8139C Ethernet LAN controller that is fully compliant with IEEE 802.3u 10/100Base-T CSMA/CD standa rds. The Ethernet port provides a standard RJ-45 jack on board, and LED indicators on the front side to show its Link (Green LED) and Active (Y ellow LED) status.
2.8 PCMCIA: PC Card Slot The UNO-2170 provides one PC Card slot that supports CardBus (Card- 32) cards and 16-bit (PCMCIA 2.1/JEIDA 4.2) card standards. It supports +3.3 V , +5 V and +12 V @ 120 mA working voltage. The PC Card is 85.6 mm long by 54 mm wide (3.
2.10 Battery Backup SRAM UNO-2170 provides 512 KB of battery backed SRAM. This ensures that you have a safe place to store critical data. Y ou can now write software applications without being concerned that system crashes will erase criti- cal data fro m th e memory .
UN O- 21 70 U se r M an ual 16.
3 2 Initial Setup This chapter introduces how to initialize the UNO-2170. Sections include: • Introduction • Inserting a CompactFlash™ Card • Chassis Grounding • Connecting Power • Connect.
Chapter 3 Initial Setup 3.1 Inse rtin g a CompactFlash Car d The procedure for installing a CompactFlas h™ card into the UNO-2170 is detailed below , please follow these steps carefully . 1. Remove the power cord. 2. Unscrew the four screws from the rear panel of the UNO-2170.
Yo u can select if you wish to combine the chassis grounding point with the system grounding by using an onboard jumper selection. (JP7) Open - Separates system power ground and chassis ground. (defau lt) Closed - Connects system power ground and chassis ground.
UN O- 21 70 U se r M an ual 20.
A System Settings and Pin Assignment s.
Appendix A System Settings and Pin Assignment s A.1 System I/O Address and Interrup t Assignment T able A.1: UNO-2170 System I/O Por ts Addr ess Range Device 000 -0 1F DM A con tro ll er ( sl av e) 02.
T able A.1: UNO-2170 System I/O Por ts Addr ess Range Device 3D0 -3 DF Color /g ra phi cs mo nit or ada pt er 3F0 -3 F7 D is ket te con tr ol ler 3E 8-3E F Se ri al p or t 3 3F8-3FF Serial port 1 443 W a tc hd og t im er DC000-DF FFF Battery backup resource Ta b l e A.
A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-2170 board. The following sections tell you how to configure the UNO-2170 hardware setting. Fi gure A-1 and Figure A-2 show the locations of UNO-2170’s connectors and jumpers.
Ta b l e A . 3 : UNO-2170 Connectors and Jumpers Label Function CN1 Phoenix power connecto r CN 2 Eth erne t po rt 1 CN 5 Et her net po rt 2 CN 3 COM 1 RS -2 32 se rial po rt CN 4 COM 2 RS -2 32 se ri.
A.3 RS-232 St andard S erial Port (COM1~COM2) T able A.4: RS-232 standard serial port pin assignment s Pin R S- 232 Si gnal Name 1 DC D 2 Rx D 3 TxD 4 DTR 5 GN D 6 DS R 7 R TS 8 CTS 9 RI UN O- 21 70 U.
A.4 RS-232/422/485 Serial Port (COM3~COM4) Ta b l e A.5: RS-232/422/4 85 serial po rt pin assignmen ts Pi n RS -23 2 RS -4 22 RS -4 85 1 DCD Tx- D A T A- 2 Rx D Tx+ D A T A + 3 TxD Rx+ NC 4 DTR Rx- NC 5 GND GND GND 6 DSR NC NC 7 R T S NC NC 8 CTS NC NC 9 RI NC NC A.
A.6 Phoenix Pow er Connector (PWR) Ta b l e A.7: Power connector pin ass ignme nt s Pin 10/ 10 0Ba se -T S ign al Na me 1 +9~36VDC 2 GN D A.7 PS/2 Keyboard and Mouse Connector T able A.
A.8 USB Connector ( USB1~USB2) Ta b l e A.9: USB connector pi n as sign me nt s Pi n Si gn al Na me Ca bl e C ol or 1 VCC Red 2 DA T A+ White 3 DA T A - Green 4 GND Black A.
UN O- 21 70 U se r M an ual 30.
B Programming the W atchdog T imer.
Appendix B Programming the W atchdog T imer Bellow is a sample of programming code for con tro lling the Watchdog Timer function . ------------- ---------- ------------- ------------- ---------- -----.
33 Appe nd ix B.
UN O- 21 70 U se r M an ual 34.
Een belangrijk punt na aankoop van elk apparaat B&B Electronics UNO-2170 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen B&B Electronics UNO-2170 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens B&B Electronics UNO-2170 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding B&B Electronics UNO-2170 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over B&B Electronics UNO-2170 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van B&B Electronics UNO-2170 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de B&B Electronics UNO-2170 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met B&B Electronics UNO-2170 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
