Gebruiksaanwijzing /service van het product MHC-NX3AV Operating Instructions (primary manual) van de fabrikant Sony
Ga naar pagina of 52
1 ©1999 by Sony Corporation Mini Hi-Fi Component System Operating Instructions 3-867-107- 14 (1) MHC-NX3A V Owner’s Record The model and serial numbers are located on the rear panel. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
2 WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
3 T able of Contents Getting Started Step 1: Hooking up the system ............ 4 Step 2: Setting up your speakers ......... 7 Step 3: Setting the time ......................... 9 Step 4: Presetting radio stations ........ 10 Saving the power in standby mode .
4 2 2 2 34 4 3 6 5 1 7 3 Getting Started Step 1: Hooking up the system Do the following procedure 1 to 7 to hook up your system using the supplied cords and accessories. If you set up the stereo system vertically Be sure to place the A/V control amplifier on top of the CD player/stereo cassette deck.
5 + – R L + Insert only the stripped portion. Black/ Stripe ( ’ ) Red/ Solid ( ‘ ) 1 Connect the flat cord to the SYSTEM CONTROL connectors until it clicks. 2 Connect the front speakers. Connect the speaker cords to the FRONT SPEAKER jacks as below.
6 6 For models with a voltage selector, set VOLTAGE SELECTOR to position of your local power line voltage. 7 Connect the power cord to a wall outlet. The demonstration appears in the display. When you press 1/u , the system turns on and the demonstration automatically ends.
7 Step 2: Setting up your speakers Connecting the supplied rear and centre speakers enables you to fully enjoy Dolby Pro Logic Surround sound. Dolby Pro Logic Surround is a decoding system standardized in TV programmes and movies. Dolby Pro Logic Surround improves the sound image by using four separate channels.
8 n + – 0 g ) ≠ + – + PRO LOGIC 1 Press PRO LOGIC. “PRO LOGIC ON” appears. 2 Press T. TONE on the remote. The test tone is heard from the speakers in the following order.
9 1 Press CLOCK/TIMER. The hour indication flashes. 2 Press V or v to set the hour. The clock is on a 24-hour system for the European model and a 12-hour system for other models. 3 Press ENTER. The minute indication flashes. 4 Press V or v to set the minute.
10 TUNED STEREO TUNED STEREO MHz – + 0 g ) ≠ + – + n n Preset number Step 4: Presetting r adio stations You can preset the following number of stations: – 2 band model: 20 for FM, 10 for AM. – 3 band model: 20 for FM, 10 for MW, and 10 for SW, or 20 for FM, 10 for AM and 5 for UKV, depending on the model you purchased.
11 TUNED STEREO – + 0 g ) ≠ + – + POWER SAVE/DEMO (STANDBY) DISPLAY To tune in a station with a weak signal Press + or – repeatedly in step 2 to tune in the station manually. To set another station to the exist preset number Start over from step 1.
12 1 Press one of the CD 1~5 § buttons and place a CD on the disc tray. If a disc is not placed properly it will not be recognized. Press the same button to close the disc tray. To insert other CDs, press § of other numbers to open the disc tray. 2 Press one of the DISC 1~5 buttons.
Basic Operations 13 1 2 3 4 5 § § § · ª · π ª · π ∏ π DOLBY NR π ª The CD SYNC button lets you record from a CD to a tape easily. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is adjusted automatically.
14 ) 0P + =p · · ª · ª · p =/+ V v b B VOLUME +/– – + 0 g ) ≠ + – + VOLUME STEREO/MONO –/+ 2 Press one of the CD 1~5 § buttons and place a CD. Then press again to close the disc tray. 3 Press CD SYNC. Deck B stands by for recording and the CD player stands by for playback.
Basic Operations 15 TUNED STEREO MHz 1 Press TUNER BAND repeatedly until the band you want appears in the display. The bands you can receive vary depending on the model you purchased.
16 TUNED STEREO MHz – 0 g + ) ≠ + – + 1 2 3 4 5 § § § · ª · π ª · π ∏ π DOLBY NR π ª –/+ 3 Press § and insert a recordable tape into deck B. 4 Press REC PAUSE/START. Deck B stands by for recording.
Basic Operations 17 ) 0P + =p · · ª · ª · p DECK A ª· p 0/) DECK B ª· V v b B VOLUME +/– Playing a tape continued You can use any type of tape, TYPE I (normal), TYPE II (CrO 2 ) or TYPE IV (metal), since the deck automatically detects the tape type.
18 DOLBY NR Searching for the beginning of a track (AMS*) During playback, turn the jog dial the same direction as the ª or · indicator to go forward. Turn the opposite direction to go back. (Or press = or + on the remote.) The search direction, + (forward) or – (back), and number of songs being skipped (1~9) appear in the display.
Basic Operations 19 1 Press § and insert a recorded tape in deck A and a recordable tape in deck B. 2 Press HI DUB. Deck B stands by for recording. 3 Press DIRECTION repeatedly to select A to record on one side. Select ß (or RELAY) to record on both sides.
20 – + 0 g ) ≠ + – + DISPLAY The CD Player n n / Press DISPLAY. Each time you press the button during normal playback or in the stop mode, the display changes as follows: During normal playback Playing time on the current track µ Remaining time on the current track µ Remaining time on current CD (1 DISC mode) or “--.
21 – + 0 g ) ≠ + – + 1 2 3 4 5 § § § · ª · π ª · π ∏ π DISC 1~5 – + 0 g ) ≠ + – + REPEAT PLAY MODE Playing the CD tracks in random or.
22 – + 0 g ) ≠ + – + 1 2 3 4 5 § § § · ª · π ª · π ∏ π π Pr ogr amming the CD tr acks –– Programme Play You can make a programme of up to 32 tracks from all the CDs in the order you want them to be played.
23 PROGRAM 1 Press CD, then place a CD. 2 Press PLAY MODE repeatedly until “PROGRAM” appears in the display. 3 Press one of the DISC 1~5 buttons to select a CD. To programme all the tracks on a CD at once, proceed to step 5. 4 Turn the jog dial until the desired track appears in the display.
24 You can record from CD, tape, or radio as you like. For example, you can record just the songs you want or record from the middle of the tape. The recording level is adjusted automatically. 1 Insert a recordable tape into deck B. 2 Press one of the function buttons you want to record (e.
25 1 Place a CD and insert a recordable tape into deck B. 2 Press CD. 3 Press PLAY MODE repeatedly until “PROGRAM” appears in the display. 4 Press one of the DISC 1~5 buttons to select a CD. 5 Turn the jog dial until the desired track appears in the display.
26 Selecting tape length automatically — Tape Select Edit You can check the most suitable tape length for recording a CD. Note that you cannot use Tape Select Edit for discs containing more than 20 tracks. 1 Insert a CD. 2 Press CD. 3 Press EDIT (EDIT/PTY on European model) once so that “EDIT” flashes.
27 – 0 g + ) ≠ + – + GROOVE DBFB PHONES Sound Adjustment For a powerful sound (GROOVE) Press GROOVE. The volume switches to power mode, DBFB is automatically set to full strength, the equalizer curve changes, and GROOVE button lights up. Press GROOVE again to return to the previous volume.
28 – + 0 g ) ≠ + – + Selecting the audio emphasis The audio emphasis menu lets you select the sound characteristic according to the sound you are listening to. Selecting the effect from the music menu 1 Press FILE SELECT. The last effect chosen appears in the display.
29 Selecting the surr ound effects You can enjoy surround effect. Changing the brightness of the display You can enjoy changing the brightness of the display while listening to the music. V v b B ) 0P · p DSP ) 0P + =p · · ª · ª · p DIMMER V v b B / Press DSP repeatedly to select the surround effect you desire.
30 Enjoying the Dolby Pr o Logic Surr ound sound You can enjoy the Dolby Pro Logic Surround sound of videos that are Dolby Surround encoded ( q ). Complete the setup and adjustments first (see page 7). / Press PRO LOGIC while playing a program source.
31 1 DISCS ALL 1 Select the audio emphasis you want for your basic sound (see “Selecting the audio emphasis” on page 28). 2 Press GEQ. 3 Press B or b to select frequency, press V or v for the desired frequency band to adjust level.
32 2 Press P FILE. The personal file number flashes in the display. 3 Press B or b to select the file number (P FILE) where you want to store the sound effect. 4 Press ENTER. The adjusted sound effects are stored under the selected file number. The settings previously stored at this memory location are erased and replaced by the new settings.
33 To check the RDS information Each time you press DISPLAY, the display changes as follows: Tip Pressing and holding DISPLAY for 2 seconds or more switches the spectrum analyzer ON/OFF. Locating a station by programme type (PTY) You can locate a station you want by selecting a programme type.
34 CULTURE Programmes about national or regional culture, language, and social concerns. SCIENCE Programmes about the natural sciences. VARIED Programmes containing celebrity interviews, panel games, and comedy. POP Popular music programmes. ROCK Rock music programmes.
35 · · ª SLEEP JAZZ Jazz programmes. COUNTRY Country music programmes. NATION Programmes featuring the popular music of the country or region. OLDIES Programmes featuring oldies music. FOLK Folk Music Programmes. DOCUMENTARY Investigative features.
36 5 Set the time to start playback. Press V or v to set the hour, then press ENTER. The minute indication starts flashing. Press V or v to set the minute, then press ENTER. The hour indication flashes again. 6 Set the time to stop playback following the above procedure.
37 4 Set the time to start recording. Press V or v to set the hour, then press ENTER. The minute indication starts flashing. Press V or v to set the minute, then press ENTER. The hour indication flashes again. 5 Set the time to stop recording following the above procedure.
38 To the DIGITAL IN jack of the MD deck Optional components Connecting an MD deck for analog recording Make sure to match the color of the plugs and the connectors.
39 – + 0 g ) ≠ + – + MIC LEVEL MIC To the audio output of the VCR Connecting a VCR Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected VCR, press VIDEO/DVD repeatedly until “VIDEO” appears in the display.
40 – 0 g + ) ≠ + – + DVD 5.1 CH VIDEO/DVD Connecting a DVD player To the front output of the DVD player To the centre output of the DVD player To the woofer output of the DVD player To the rear output of the DVD player When your DVD player has 5.
41 Insulated wire (not supplied) Connecting external antennas Connect the external antenna to improve the reception. Refer to the instructions of each component. FM antenna Connect the optional FM external antenna. You can also use the TV antenna instead.
42 • When using CDs that have glue or similar tacky substance on the label side of the disc or that used a special ink when the label was printed, there is a chance that the CD or label may become attached to parts inside this unit. When this occurs, it may not be possible to remove the CD, and may also cause this unit to malfunction.
43 T roubleshooting If you run into any problem using this stereo system, use the following check list. First, check that the power cord is connected firmly and the speakers are connected correctly and firmly. Should any problem persist, consult your nearest Sony dealer.
44 There is severe hum or noise. • A TV or VCR is placed too close to the stereo system. Move the stereo system away from the TV or VCR. • The A/V control amplifier is placed under the CD player/stereo cassette deck. Place the A/V control amplifier on the top of the CD player/stereo cassette deck.
45 Tape Deck The tape does not record. • No tape in the cassette holder. • The tab has been removed from the cassette (see “To save a tape permanently” on page 42). • The tape has reeled to the end. The tape does not record nor play or there is a decrease in sound level.
46 Specifications European model Front Speaker: DIN power output (rated) 90 + 90 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 110 + 110 watts (6 ohms at 1 kHz, 10% THD) Music p.
47 Inputs VIDEO IN: voltage 250 mV, (phono jacks) impedance 47 kilohms MD IN: voltage 450 mV, (phono jacks) impedance 47 kilohms DVD INPUT: FRONT IN: voltage 450 mV, (phono jacks) impedance 47 kilohms.
48 Specifications (continued) Speaker Front Speaker (SS-NX1) Speaker system 2-way, bass-reflex type, magnetically shielded type Speaker units Woofer: 17 cm (6 3 / 4 in.), cone type Tweeter: 2.5 cm (1 in.), dome type Nominal impedance 6 ohms Dimensions (w/h/d) Approx.
49.
50.
51.
52 Sony Corporation Printed in Malaysia Index A Adjusting the graphic equalizer 31 the sound 27 the volume 8, 13, 18 Aerials 5, 41 Automatic Source Selection 13, 15, 18 B Batteries 6 C CD player 20 CD Synchro Recording 13 Clock setting 9 Connecting.
Een belangrijk punt na aankoop van elk apparaat Sony MHC-NX3AV Operating Instructions (primary manual) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sony MHC-NX3AV Operating Instructions (primary manual) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sony MHC-NX3AV Operating Instructions (primary manual) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sony MHC-NX3AV Operating Instructions (primary manual) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sony MHC-NX3AV Operating Instructions (primary manual) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sony MHC-NX3AV Operating Instructions (primary manual) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sony MHC-NX3AV Operating Instructions (primary manual) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sony MHC-NX3AV Operating Instructions (primary manual) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
