Gebruiksaanwijzing /service van het product MVE-9000-C van de fabrikant Sony
Ga naar pagina of 36
INSTALLATION MANUAL 1st Edition DME PROCESSOR PACK MVE-9 0 00-C MVE-9000 MULTI FORMAT DME PROCESSOR HK-PSU04 MKE-9020M MKE-9021M MKE-9040M.
MVE-9000 IM MVE-9000 Serial No. 10001 and Higher HK-PSU04 Serial No. 10001 and Higher MKE-9020M Serial No. 10001 and Higher MKE-9021M Serial No. 10001 and Higher MKE-9040M Serial No. 10001 and Higher ! WARNING This manual is intended for qualified service personnel only.
MVE-9000 IM For MVE-9000 Attention-when the product is installed in Rac k: 1. Prevention against o verloading of branch cir cuit When this product is installed in a rack and is supplied power from an outlet on the r ack, please make sure that the r ack does not o verload the supply circuit.
.
1 MVE-9000 IM Table of Contents Manual Structure Purpose of this manual .............................................................................................. 2 Related manuals ..................................................................
2 MVE-9000 IM Purpose of this manual This manual is the installation manual of DME Processor Pack MVE-9000-C and their optional boards and units. This manual is intended for use by trained system and service engineers, and describes the information on installing the MVE-9000-C system.
1-1 MVE-9000 IM Section 1 Installation 1-1. Operating Environment Operating guaranteed temperature : + 5 d C to + 40 d C Performance guaranteed temperature : + 10 d C to + 35 d C Operating humidity : 10 % to 90 % (relative humidity) Storage temperature : _ 20 d C to + 60 d C Mass (when all options are installed) : Approx.
1-2 MVE-9000 IM 1-2-2. Recommended Power Cord This unit does not come with a power cord. To get a power cord, please contact your local Sony Sales Office/Service Center. w . Use the approved Power Cord (3-core mains lead)/ Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
1-3 MVE-9000 IM 375 61 380 144.5 115.5 115.5 17.5 482 37.2 101.6 176(4U) 161 465 440 35 7 520 Unit : mm 1-3. Installation Space (External dimensions).
1-4 MVE-9000 IM 1-4. Installing the Options The MVE-9000-C is shipped from the factory with the necessary option (refer to the following table) already installed in the MVE-9000, in accordance with the speci- fied system configuration.
1-5 MVE-9000 IM 4. While the eject levers are kept open as shown in the illustration, insert the plug-in board into the board guide rails. Name of option Name of board Slot on the front side MKE-9040M.
1-6 MVE-9000 IM 1 2 3 Fixing screw Fixing screw Connector board Blank panel B3 x 5 B3 x 5 1 2 3 4 5 6 7 8 1-4-2. Installing the Connector Board The board slot Name of option Name of board Slot on the rear side MKE-9020M CN-2357A board 3 CN-2357B board 5 MKE-9021M CN-2355A board 3 CN-2355B board 5 Installation procedure 1.
1-7 MVE-9000 IM Connecting cable Harness suppor t 1 2 3 4 5 6 7 8 PSW3 x 6 1 2 3 4 5 6 7 8 Cov er panel B3 x 5 B3 x 5 4. Remove the blank panel from the slots 2 and 4. 5. Attach the cover panel and secure it with the two screws. 6. Attach the connecting cable on the harness support.
1-8 MVE-9000 IM 1-5. Rack Mounting The MVE-9000 installs in a 19-inch standard rack. To mount the MVE-9000 in a rack, use the specified rack mount kit and follow the procedure described below.
1-9 MVE-9000 IM 7. Fix the rack angles in the rack using the specified screws. 8. Install the front panel to the equipment. Rack Rack angle Rack angle B5 x 12 B5 x 12 3. Attach the right and left adaptors to the rack complete- ly using the specified six screws.
1-10 MVE-9000 IM 1-6. Matching Connectors and Cables Use the following connectors, cables or equivalents when connecting cables to the unit. Model name Panel indication Connector name Matching connector and cable Name Sony part No.
1-11 MVE-9000 IM <Relay> GPI OUT n B GPI OUT 5-8 GPI OUT COM <Open collector output> n;1-4 + V GPI OUT n A ( * 2) ( * 3) 1-7. Input/Output Signals of Connectors The input/output signals of the connectors at the rear panel are as follows. n <CONTROLLER> indicates a controlling device.
1-12 MVE-9000 IM 1-8. Checks on Completion of Installation 1-8-1. On-board Switches Setting and LED Functions n The number shown in parentheses ( ) indicates the address on the circuit board.
1-13 MVE-9000 IM D602 (A-2) : PLL LOCK status LED REF IN signal format status indication. Lit when the REF IN signal matches with the switcher format setup. D701 (A-2) : SBUS RX status LED S-BUS receive status indication. Lit while the data receive is in progress.
1-14 MVE-9000 IM <Connector> CN103 (A-4) : TERMINAL pin This pin is connected to the main CPU control terminal and used during maintenance. Conforms to RS-232C. CN401 (A-5) : TERMINAL pin This pin is connected to the IEEE1394 control terminal and used during maintenance.
1-15 MVE-9000 IM <LED on the CPU-DK module> : COM CPU-1 : COM CPU-2 DI1 (green) (B-5) : CD (Card Detect) status LED Lit when the CPU-DK module is inserted correctly to the parent board. DI2 (green) (F-3) : RUN status LED Lit when the CPU-DK module starts operating.
1-16 MVE-9000 IM <LED on the SG-272 board> D100 (B-1) : REF OK status LED Lit while V sync of the reference input is detected. D101 (B-1) : REF EXT status LED Lit while sync signal is input to the reference input. D200 (B-1) : LOCK status LED Lit while the machine is locked to the reference signal.
1-17 MVE-9000 IM 1 2 3 4 5 7 6 ABC D EF G H D3801 D3802 D3803 D3804 TP3801 TP3802 TP3803 TP3804 D3701 D3703 D3702 D3704 ND3802 ND3801 ND3902 ND3901 D3091 D3902 D3903 D3904 TP3091 TP3902 TP3903 TP3904 .
1-18 MVE-9000 IM D3704 (H-2) : SYSTEM status LED Lit when configuration is complete and FPGA reset is also complete. If the LED does not light, the FPGA may be defective. D3705 (H-5) : CN EXIST status LED CN-2357 board presence/absence status indication.
1-19 MVE-9000 IM <LEDs on the CPU-DR module> (G-2), (G-5) Refer to <LED on the CPU-DR module> in “1. CA- 54CFA Board”. <Switches on the CPU-DR module> (G-2), (G-5) Refer to <Switches on the CPU-DR module> in “1. CA- 54CFA Board”.
1-20 MVE-9000 IM AB C D E F G H J K L M N P R 1 2 3 4 5 6 7 8 9 10 11 12 13 TP601 D601 D605 D604 D602 E608 E606 CN3202 CN4001 D3304 D3302 D3303 D3301 D3401 D3402 D3403 D3404 ND3401 ND3402 E607 E627 E6.
1-21 MVE-9000 IM TP701 (G-7), TP801 (G-7), TP901 (E-7), TP1001 (E-7), TP1101 (K-6), TP1201 (K-6), TP1301 (J-6), TP1401 (H-6), TP1501 (N-6), TP1601 (N-6), TP1701 (M-6), TP1801 (M-6) : ERR terminal Used for design purpose. TP3102 (C-6) : CKX (control timing) signal check terminal Use this terminal to check the CKX signal supplied from mother board.
1-22 MVE-9000 IM CONTROL CTRL REMO TE 1-4 D ATA REMO TE D A T A CTRL REMO TE 1 D ATA PERIPH PERIPH Reference video signal b) BVE-9100 Editing Control System Ethernet switch a) MVE-9000-C DME Processor.
1-23 MVE-9000 IM SWITCHER B SWITCHER A DME 1B DME 1A PRIMAR Y INPUTS 1-68 PRIMAR Y INPUTS 69-80 OUTPUTS 1 - 48 MONI OUT EXT IN MONIT OR OUTPUTS 1-8 MVE-9000-C DME Processor Pack Reference video signal.
1-24 MVE-9000 IM CONTROL CTRL REMO TE 1-4 D ATA REMO TE D A T A CTRL REMO TE 1 D ATA PERIPH PERIPH Reference video signal b) BVE-9100 Editing Control System Ethernet switch a) MVE-9000-C DME Processor.
1-25 MVE-9000 IM V . K IN/EXT IN PRIMAR Y INPUTS 1 - 68 MONIT OR OUTPUTS 1-8 OUTPUTS 1-48 MONI OUT V . K OUT MVE-9000-C DME Processor Pack Reference video signal c) Monitor Monitor MVS-8400/8300/8200 .
.
2-1 MVE-9000 IM Flow2 The monitor picture is not display ed correctly ev en though the main power of the MVE-9000 is turned on. Are the plug-in boards inser ted into their correct slots? Are the option boards inser ted into their correct slots? Are the input and output cables connected correctly? Inser t the plug-in boards into the correct slots .
2-2 MVE-9000 IM 2-3. About the Data Backup Capacitor A large capacitor is installed on the CA-54CFA board in order to backup the memory storing the setup and other data in the MVE-9000. Leave the main power of the MVE- 9000 turned on for an hour or longer in order to charge this capacitor.
MVE-9000 IM The material contained in this manual consists of inf or mation that is the property of Sony Cor poration. Sony Corporation e xpressly prohibits the duplication of any portion of this manu.
Printed in Japan Son y Cor poration 2003. 4 08 B&P Company ©2003 MVE-9000-C (SY) E 3-790-017-01.
Een belangrijk punt na aankoop van elk apparaat Sony MVE-9000-C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sony MVE-9000-C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sony MVE-9000-C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sony MVE-9000-C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sony MVE-9000-C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sony MVE-9000-C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sony MVE-9000-C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sony MVE-9000-C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
