Gebruiksaanwijzing /service van het product SY-7IZB+ van de fabrikant SOYO
Ga naar pagina of 68
SY-7IZB+ Motherboard **************************************************** Socket 370 for Intel Celeron TM Processor Intel 440 ZX AGP/PCI Motherboard 66 &100MHz Front Side Bus supported Baby AT For.
SOY O ™ SY-7IZB+ ii About This Guide This User's Guide is for assisting system manufacturers and end users in setting up and installing the Motherboard. Information in this guide has been carefully checked for reliability; however, no guarantee is given as to the correctness of the contents.
Table of Contents SY-7IZB+ iii Table of Contents SY-7IZB+ MOTHERBOARD L AYOUT ........................................... 1 CHAPTER 1 INTRODUCT ION ..................................................... 2 1-1 KEY FE ATURES .............................
Motherboard Features SY-7IZB+ 1 SY-7IZB+ MOTHERBOARD L AYOUT SY-7IZB+ Platform Flash BIO S AGP Slo t K B Connecto r PS/2 Mouse Connector ATX Powe r AT Powe r PRT 1 1 COM 2 1 FD C 1 IDE 1 1 IDE 2 1 3 V.
Introduction SY-7IZB+ 2 Chapter 1 INTRODUCTION The SY-7IZB+ AGP/PCI Motherboard is a high-performance Celeron ® processor supported Baby AT form-factor system board. SY-7IZB+ uses the 440 ZX Chipset technology and supports Socket 370 Celeron TM processors.
Introduction SY-7IZB+ 3 SY-7IZB+ PL A TFORM FE A TURES Board Size 4-la yer PCB, 26 x 22cm( ” 10.24x8.7 ” ), Baby-AT Form Factor Socket 370 66/100MHz FSB Ø Celeron Processor 300A/333/366/400/433/466/500 Ø Built-in full speed 128KB L2 cache.
Introduction SY-7IZB+ 4 Keylock 5-pin KeyLock Header Reset 2-pin Reset Switch Header Speaker 4-pin PC Speaker Header TB_LED 2-pin ACPI LED Header HDD_LED 2-pin IDE Device LED Header PWRBT ATX Power On.
Introduction SY-7IZB+ 5 HANDLING THE MOTHERBOARD To a void damage to your Motherboard, follow these simple rules while unpacking: Ø Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. Ø Remove the Motherboard from its anti-static packaging.
Hardware Setup SY-7IZB+ 6 Chapter 2 HARDWARE SETUP Congratulations on your purchase of SY-7IZB+ Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti-static packaging until you have made the following preparations.
Hardware Setup SY-7IZB+ 7 2-2 UNPACKING THE MOTHERBOARD When unpacking the Motherboard, check for the following items: Ø The SY-7IZB+ 440 ZX AGP/PCI Motherboard Ø This Quick Start Guide * Ø The Ins.
Hardware Setup SY-7IZB+ 8 2-3 INSTALL A TION GUIDE We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation.
Hardware Setup SY-7IZB+ 9 Follow these steps to install the CPU in the Socket 370: 1. Lift the socket handle up to a vertical position. 2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the socket. 3. Seat the processor in the socket completely and without forcing.
Hardware Setup SY-7IZB+ 10 Step 3. SDRAM Memory Module Installation This Motherboard features 3 x DIMM for 168-pin 3.3V unbuffered DIMM modules, providing support for up to 256MB of main memory using DIMM modules from 8MB to 128MB.
Hardware Setup SY-7IZB+ 11 Step 4. IDE Device Installation (HDD, CD-ROM) This Motherboard offers two primary and secondary IDE device connectors (IDE1, IDE2).
Hardware Setup SY-7IZB+ 12 Step 6. Front Panel Connections Plug the computer case's front panel devices to the corresponding headers on the Motherboard. 1. Power LED & KeyLock Plug the Power LED cable into the 5-pin Keylock header. Some systems may feature a KeyLock function with a front panel switch for enabling or disabling the keyboard.
Hardware Setup SY-7IZB+ 13 Attach the 4-pin PC speaker cable from the case to the Speaker header on the Motherboard. 4. ACPI LED Connecting the 2-pin ACPI LED cable to the corresponding ACPI LED header will cause the LED to light whenever the system is in ACPI mode.
Hardware Setup SY-7IZB+ 14 Step 7. External Peripherals Connections External devices such as the keyboard, printer, PS/2 mouse, modem, USB can be connected to the Motherboard. Normally, you can not plug your devices directly onto the Motherboard, except for the keyboard that plugs directly into the back panel KB connector.
Hardware Setup SY-7IZB+ 15 1. Serial Ports COM1/COM2 External Devices that use the COM ports include serial mice and modems. The COM port connectors are located on 2 separate brackets panels, as shown on the figure below. Please plug their respective 10 pin flat cable connectors into the COM1 and COM 2 serial port connectors on the Motherboard.
Hardware Setup SY-7IZB+ 16 Parallel Port PRT1 This parallel port is used to connect the printer or other parallel devices. Your Motherboard comes with one 25-pin female external parallel connector with 25-pin flat cable.
Hardware Setup SY-7IZB+ 17 PS/2 Mouse Attach the mouse cable to the 6-pin male PS/2 mouse connector on the Motherboard to enable PS/2 mouse function. Universal Serial Bus (USB) This Motherboard provides a dual-row 10-pin header (one pin is empty) to support two USB ports for your additional devices.
Hardware Setup SY-7IZB+ 18 Step 8. Other Connections 1. Wake-On-LAN (WOL) Attach the 3-pin connector from the LAN card which supports the Wake-On-LAN (WOL) function to the JP44 header on the Motherboard. This WOL function lets users wake up the connected computer through the LAN card.
Hardware Setup SY-7IZB+ 19 Step 9. Cooling Fan Installation 1. CPU Cooling Fan After you have seated the CPU properly on the processor , attach the 3-pin fan cable to the CPUFAN connector on the Motherboard. The fan will stop when the system enters into Suspend Mode.
Hardware Setup SY-7IZB+ 20 Step 10. AGP VGA Card Insert the AGP VGA card into the AGP slot. Then connect the monitor information cable to the AGP card back plane external connector. Follow the manufacturer's instructions to perform the AGP VGA drivers installation.
Hardware Setup SY-7IZB+ 21 3.3 V -12 V GN D PS-O N GN D GN D GN D -5 V 5V 5V 3.3V 3.3V GN D 5V GN D 5V GN D PW-O K 5VS B 12V ATX Powe r Warning: Follow these precautions to preserve your Motherboard f.
Hardware Setup SY-7IZB+ 22 Step 14. CMOS Clearing (JP5) After you have turned off your computer, clear the CMOS memory by momentarily shorting pins 2-3 on jumper JP5, for a few seconds. Then restore JP5 to the initial 1-2 jumper setting in order to recover and retain the default settings.
Hardware Setup SY-7IZB+ 23 Step 16. Power-On by Keyboard Jumper (JP10) You can choose to enable the Power-On by Keyboard or Mouse function by shorting pin 1-2 on jumper JP1, otherwise, short pin 2-3 to disable this function.
Hardware Setup SY-7IZB+ 24 Repeat this operation until you get the following screen. 3. The BIOS Setup screen appears: Step 18. Quick BIOS Setup This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP] .
Hardware Setup SY-7IZB+ 25 2. Select [STANDARD CMOS SETUP] Set [Date/Time] and [Floppy drive type] , then set [Hard Disk Type] to “ Auto ” . 3. Select [SOYO COMBO SETUP] Move the cursor to the [CPU Frequency] field to set the CPU frequency, as shown in the following display.
Hardware Setup SY-7IZB+ 26 4. Select [S AVE & EXIT SETUP] Press <Enter> to save the new configuration to the CMOS memory, and continue the boot sequence.
BIOS Setup Utility SY-7IZB+ 27 Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utility.
BIOS Setup Utility SY-7IZB+ 28 Hot Keys: Function keys give you access to a group of commands throughout the BIOS utility. Function Command Description F1 Help Gives the list of options available for each item. Shift F2 Color Change the color of the display window.
BIOS Setup Utility SY-7IZB+ 29 3-1 SOYO COMBO SETUP This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP].
BIOS Setup Utility SY-7IZB+ 30 3-1.1 Quick CPU Frequency Setup Quick CPU Frequency Setup Setting Description 66/33 MHz 105/35 MHz 75/37 MHz 110/36 MHz 83/41 MHz 115/38 MHz 100/33 MHz 120/40 MHz 103/34.
BIOS Setup Utility SY-7IZB+ 31 3-1.3 System Boot Control Settings System Boot Control Settings Setting Description Note A, C, SCSI C, A, SCSI C, CD-ROM, A CD-ROM, C, A D, A, SCSI E, A, SCSI F , A, SCS.
BIOS Setup Utility SY-7IZB+ 32 Power Management (Continued) PM Events Setting Description Note Disabled Set to disable the system can only wake up through the password (In case the password has been forgotten, use JP8 to clear the password) Power button Enabled Set to enable the system can wake up through the password and the power button.
BIOS Setup Utility SY-7IZB+ 33 3-1.5 CPU Device Monitoring CPU Device Monitoring Setting Description Note Disabled Default CPU Warning Temperature Enabled Set CPU temperature from 50 ° C to 70 ° C. The CPU will slow down when CPU temperature goes beyond the preset value.
BIOS Setup Utility SY-7IZB+ 34 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] key. ROM PCI/ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC.
BIOS Setup Utility SY-7IZB+ 35 3-2.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary (Secondary) Master & Slave Setting Description Note Auto BIOS detects hard disk type automatically.
BIOS Setup Utility SY-7IZB+ 36 3-2.4 Video Select the video mode: EGA/VGA (Default), CGA 40, CGA 80, Mono (Monochrome). 3-2.5 Halt On When the BIOS detects system errors, this function will stop the system. Select which type of error will cause the system halt: All Errors (Default), No Errors, All But Diskette, All But Keyboard, All But Disk/Key.
BIOS Setup Utility SY-7IZB+ 37 3-3 BIOS FE A TURES SETUP Select the [BIOS FEATURES SETUP] option from the Main Menu and press [Enter] key. ROM PCI/ISA BIOS BIOS FE A TURES SETUP AWARD SOFTWARE, INC. Anti-Virus Protection : Enabled Assign IRQ For VGA : Enabled CPU Internal Cache : Enabled HDD S.
BIOS Setup Utility SY-7IZB+ 38 3-3.1 Virus Warning Setting Description Note Disabled Anti - Virus Protection Enabled If set to enabled, the Paragon Anti-Virus. Function will scan your boot drive for boot virusses. If a boot virus is detected, the BIOS will display a warning message.
BIOS Setup Utility SY-7IZB+ 39 3-3.4 Security Option Use this feature to prevent unauthorized system boot-up or use of BIOS Setup. The following table describes the security settings. Setting Description System Each time the system is booted, the password prompt appears.
BIOS Setup Utility SY-7IZB+ 40 Typematic Settings (Continued) Typematic Settings Setting Description Note The following [ Typematic Rate] and [ Typematic Delay] fields are active only if [ Typematic R.
BIOS Setup Utility SY-7IZB+ 41 3-4 CHIPSET FE A TURES SETUP Caution: Change these settings only if you are already familiar with the Chipset. ROM PCI/ISA BIOS CMOS SETUP UTILITY CHIPSET FE A TURES SET.
BIOS Setup Utility SY-7IZB+ 42 3-4.1 CHIPSET FE A TURES SETUP CHIPSET FE A TURES Setting Description Note Disabled Auto Configuration Enabled It is strongly recommended to enable this option so that the system automatically sets all chipset feature options on the left panel of the screen (except for cache update & BIOS cacheable).
BIOS Setup Utility SY-7IZB+ 43 CHIPSET FE A TURES SETUP (Continued) CHIPSET FE A TURES Setting Description Note 16 BIT I/O Recovery Time 1 Use the default setting Default Disabled Default Memory Hole At 15M-16M Enabled Some interface cards will map their ROM address to this area.
BIOS Setup Utility SY-7IZB+ 44 3-5 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions. ROM PCI/ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC.
BIOS Setup Utility SY-7IZB+ 45 3-5.1 Power Management Controls Power Management Controls Setting Description Note Disabled Default ACPI function Enabled ACPI (Advanced Configuration Power Management Interface) Yes To use Advanced Power Management (APM) you must run [power.
BIOS Setup Utility SY-7IZB+ 46 3-5.2 PM Timers PM Timers Setting Description Note User Define Lets you define the HDD and system power down times. Default Disable Disables the Green PC Features.
BIOS Setup Utility SY-7IZB+ 47 3-5.3 PM Events PM Events Setting Description Note Disabled PCI/VGA Act- Monitor Enabled Enables the power management timers when a [no activity] event is detected. Default Disabled Default IRQ 8 Break Suspend Enabled Alarm function is active.
BIOS Setup Utility SY-7IZB+ 48 3-6 PNP/PCI CONFIGUR A TION SETUP This option sets the Motherboard's PCI Slots. ROM PCI/ISA BIOS PNP/PCI CONFIGUR A TION AWARD SOFTWARE, INC. Resources Controlled By : Manual Slot 1/AGP Use IRQ No. : Auto Reset Configuration Data : Disabled Slot 2 Use IRQ No.
BIOS Setup Utility SY-7IZB+ 49 3-6.1 PNP/PCI Configuration Controls PNP/PCI Controls Setting Description Note Manual BIOS does not manage PCI/ISA PnP card IRQ assignment.
BIOS Setup Utility SY-7IZB+ 50 PNP/PCI Configuration Setup (Continued) PNP/PCI Setup Setting Description Note How to set the BIOS to release the IRQ to the PnP Interrupt pool: Interrupt Line PnP / PCI.
BIOS Setup Utility SY-7IZB+ 51 3-7 LOAD SETUP DEFAULTS Select the [LOAD SETUP DEFAU LTS] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
BIOS Setup Utility SY-7IZB+ 52 3-8 INTEGR A TED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGRATED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-7IZB+ 53 3-8.1 IDE Device Controls IDE Controls Setting Description Note Disabled IDE HDD Block Mode Enabled Invokes multi-sector transfer instead of one sector per transfer.
BIOS Setup Utility SY-7IZB+ 54 3-8.4 FDC Controls FDC Controls Setting Description Note Disabled Turn off the on-board floppy controller Onboard FDC controller Enabled Use the on-board floppy controller Default 3-8.
BIOS Setup Utility SY-7IZB+ 55 Onboard Parallel Ports (Continued) Onboard Parallel Ports Setting Description Note ECP/EPP Default SPP ECP Parallel Port Mode EPP/SPP The mode depends on your external device that connects to this port.
BIOS Setup Utility SY-7IZB+ 56 3-8.7 MULTI I/O ADDRESSES Default settings for multi-I/O addresses are as follows: Port I/O Address IRQ Status LPT1 378H 7 ECP/EPP COM1 3F8H 4 COM2 2F8H 3 Warning: If a default I/O address conflicts with other I/O cards such as sound card, you must change one of the I/O addresses to remedy to this address conflict.
BIOS Setup Utility SY-7IZB+ 57 2. Choose [SUPERVISOR PASSWORD] from the Main Menu and press [Enter] . The following prompt appear: Warning: If you forget or lose the password, the only way to access the system is to set jumper JP5 to clear the CMOS RAM.
BIOS Setup Utility SY-7IZB+ 58 This diagram outlines the password selection procedure: 3-10 USER PASSWORD When the user password option is on, you are not allowed to change any setting in the [CMOS SETUP UTILITY] except for changing the user's password.
BIOS Setup Utility SY-7IZB+ 59 3-11 IDE HDD AUTO DETECTION This Main Menu function automatically detects the hard disk type and configures the STANDARD CMOS SETUP accordingly.
Driver Installation SY-7IZB+ 60 Chapter 4 DRIVERS INSTALLATION Your SY-7IZB+ Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your new Motherboard, the drivers software available for installation, and a database in HTML format with information on SOYO Motherboards and other products.
Driver Installation SY-7IZB+ 61 Step 2. Install Drivers and Utilities Click the Install Drivers button to display the list of drivers software that can be installed with your Motherboard. The Start Up program displays the drivers available for the particular model of Motherboard you own.
Driver Installation SY-7IZB+ 62 The following drivers are available for Windows 98 (Driver Installation Menu) However, to display the list of all drivers software available with SOYO Motherboards, click the Display all drivers on the SOYO CD button.
Driver Installation SY-7IZB+ 63 busmaster drivers make use of DMA (Direct Memory Access) to relieve the CPU of this burden, thus speeding up the system. The SOYO SpeedPro driver makes use of an advanced caching algorithm, which gives it an advantage over other busmaster drivers.
Driver Installation SY-7IZB+ 64 l Core voltage The core voltage differs between generations of Intel CPUs, if the Hardware monitor gives a warning, the settings for the safe range of the core voltage has to be adjusted. This can be done by simply clicking and dragging the upper and lower limit bars.
Driver Installation SY-7IZB+ 65 Step 5. Select which driver you want to install and click OK Notice 1: You may click Cancel to abort the driver installation and return to the main menu. Notice 2: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program.
Een belangrijk punt na aankoop van elk apparaat SOYO SY-7IZB+ (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen SOYO SY-7IZB+ heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens SOYO SY-7IZB+ vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding SOYO SY-7IZB+ leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over SOYO SY-7IZB+ krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van SOYO SY-7IZB+ bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de SOYO SY-7IZB+ kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met SOYO SY-7IZB+ . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
