Gebruiksaanwijzing /service van het product SY-D6IBA van de fabrikant SOYO
Ga naar pagina of 75
SY-D6IBA Motherboard *************************************************** Single or Dual Slot 1 processor supported 82440 BX AGP/PCI Motherboard 66&100MHz Front Side Bus supported ATX Form Factor U.
SOY O ™ SY-D6IBA ii About This Guide This User's Guide is for assisting system manufacturers and end users in setting up and installing the Motherboard. Information in this guide has been carefully checked for reliability; however, no guarantee is given as to the correctness of the contents.
Table of Contents SY-D6IBA iii Table of Contents SY-D6IBA MOTHERBOARD L AYOUT .......................................... 1 CHAPTER 1 INTRODUCTI ON ..................................................... 2 1-1 KEY FE ATURES ..............................
Motherboard Layout SY-D6IBA 1 SY-D6IBA MOTHERBOARD L AYOUT Back Panel SY-D6IBA Platform COM 1 COM 2 USB 1 PR T USB 2 PS/2 K B Connecto r PS/2 Mouse Connector ISA Slot # 1 ISA Slot # 2 Inte l ® 82371 .
Introduction SY-D6IBA 2 Chapter 1 INTRODUCTION The SY-D6IBA AGP/PCI Motherboard is a high-performance, Single or Dual slot 1 processor supported, ATX form-factor system board. SY-D6IBA uses the 82440 BX Chipset technology and supports most slot 1 processors.
Introduction SY-D6IBA 3 SY-D6IBA PL A TFORM FE A TURES Board Size 4-layer PCB, 25x30.5cm (9.8 ” x 12 ” ), ATX Form Factor Slot1 Slot 1 for Pentiu m ® III & Pentiu m ® II Ø Supports the foll.
Introduction SY-D6IBA 4 IDE1, IDE2 2 x 40-pin Bus Mastering E-IDE/ATAPI Ports Ø IDE1: Primary IDE Device Connector Ø IDE2: Secondary IDE Device Connector Ø Supports Ultra DMA/33 FDC 1 Floppy Disk Drive (FDD) Port (Supports 1.
Introduction SY-D6IBA 5 1-2 HANDLING THE MOTHERBOARD To a void damage to your Motherboard, follow these simple rules while unpacking: Ø Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis.
Hardware Setup SY-D6IBA 6 Chapter 2 HARDWARE SETUP Congratulations on your purchase of SY-D6IBA Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti- static packaging until you have made the following preparations.
Hardware Setup SY-D6IBA 7 2-2 UNPACKING THE MOTHERBOARD When unpacking the Motherboard, check for the following items: Ø The SY-D6IBA 82440 BX AGP/PCI Motherboard Ø The Quick Start Guide * Ø The Installation CD-ROM * Ø Two SCSI Driver Installation Diskettes labeled “ 7800 Family Manager Set V2.
Hardware Setup SY-D6IBA 8 2-3 INSTALL A TION GUIDE We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation.
Hardware Setup SY-D6IBA 9 Follow these instructions to install your Slot 1 processor correctly. Ø Retention Module 1. Open the two sides by folding them up.
Hardware Setup SY-D6IBA 10 2. Push the locks on top of the CPU inward. 3. Insert the CPU into the retention module. The CPU fits in the CPU slot in only ONE way, do not try to force it in.
Hardware Setup SY-D6IBA 11 4. After completely inserting the CPU, push the two locks on top of the CPU outward. Now your CPU is ready for use. To remove the CPU, press the two notches on top of the CPU inward. Now press the two slides on the retention module down and remove the CPU.
Hardware Setup SY-D6IBA 12 Step 2. CPU Fan Installation Your Slot 1 processor kit comes with a cooling fan. Mount the fan on the processor according to the instructions provided by the manufacturer. The fan is a key component that will ensure system stability.
Hardware Setup SY-D6IBA 13 Your board comes with four DIMM sockets, providing support for up to 1GB of main memory using DIMM modules from 8MB to 256MB. For 66MHz front side bus CPUs use 12ns or faster memory; for 100MHz front side bus CPUs use 8ns (100MHz, PC100 compliant) memory.
Hardware Setup SY-D6IBA 14 Step 5. Floppy Drive Installation The system supports 5 possible floppy drive types: 720 KB, 1.2 MB, 1.44 MB, 2.88 MB, and LS-120. In addition, this Motherboard supports a 3-mode (720KB/1.2MB/1.44MB) floppy commonly used in Japan.
Hardware Setup SY-D6IBA 15 2. Reset Plug the Reset push-button cable into the 2-pin Reset header on the Motherboard. Pushing the Reset button on the front panel will cause the system to restart the boot-up sequence. 3. Speaker Attach the 4-pin PC speaker cable from the case to the Speaker header on the Motherboard.
Hardware Setup SY-D6IBA 16 Step 7. Back Panel Connections All external devices such as the PS/2 keyboard, PS/2 mouse, printer, modem, USB can be plugged directly onto the Motherboard back panel. Only after you have fixed and locked the Motherboard to the computer case can you start connecting the external peripheral devices.
Hardware Setup SY-D6IBA 17 2. Parallel Port PRT This parallel port is used to connect the printer or other parallel devices. Plug the parallel device cable into the 25-pin female connector located at the rear panel of the Motherboard.
Hardware Setup SY-D6IBA 18 Please install according to the following pin assignment: 2. Infrared (IR1) Plug the 5-pin infrared device cable to the IR1 header. This will enable the infrared transfer function. This Motherboard meets both the ASKIR and HPSIR specifications.
Hardware Setup SY-D6IBA 19 To a void damage to the system, install according to the following pin assignment: 2. Chassis Cooling Fan (FAN 3) Some chassis also feature a cooling fan. This Motherboard features a FAN 3 connector to provide 12V power to the chassis fan.
Hardware Setup SY-D6IBA 20 Step 10. AGP VGA Card Insert the AGP VGA card into the AGP slot. Then connect the monitor information cable to the AGP card back plane external connector. Follow the manufacturer's instructions to perform the AGP VGA drivers installation.
Hardware Setup SY-D6IBA 21 Warning: Follow these precautions to preserve your Motherboard from any remnant currents when connecting to ATX power supply: Turn off the power supply and unplug the power cord of the A TX power supply before connecting to A TX PW connector.
Hardware Setup SY-D6IBA 22 Step 13. Power-On by PS/2 Keyboard Jumper (JP1) You can choose to enable the Power-On by PS/2 Keyboard function by shorting pin 1-2 on jumper JP1, otherwise, short pin 2-3 to disable this function. Power-On by PS/2 Keyboard Enable Disable JP1 Setting Short pin 2-3 to enable the Power-On by PS/2 Keyboard function.
Hardware Setup SY-D6IBA 23 Step 15. Power Button Enable (JP2) Your system can be power on by either pressing a power button or typing in a password, which can be set in the BIOS SOYO COMBO Setup. To a void being unable to power up the system due to of forgetting the password, you can place a jumper cap to short JP2.
Hardware Setup SY-D6IBA 24 3. The BIOS Setup screen appears: Step 17. Quick BIOS Setup This Motherboard does not use any hardware jumpers to set the CPU frequency.
Hardware Setup SY-D6IBA 25 3. Select [SOYO COMBO SETUP] Move the cursor to the [CPU Frequency] field to set the CPU working frequency, as shown in the following display. Available [CPU Frequency] settings on your SY-D6IBA Motherboard are detailed in the following table.
Hardware Setup SY-D6IBA 26 Step 18. Power Off There are two possible ways to turn off the system: 1. Use the Shutdown command in the Start Menu of Windows 95/98 to turn off your computer. 2. Press the mechanical power-button and hold down for over 4 seconds, to shutdown the computer.
Hardware Setup SY-D6IBA 27 Troubleshooting at First Start l What should I do if the Motherboard refuses to start? The 350MHz setting is used as default so whenever the BIOS settings are erased or reset, the board will be able to boot up.
Hardware Setup SY-D6IBA 28 You are now ready to configure your system with the BIOS Setup program. Please go to Chapter 3: BIOS SETUP.
BIOS Setup Utility SY-D6IBA 29 Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utility.
BIOS Setup Utility SY-D6IBA 30 Hot Keys: Function keys give you access to a group of commands throughout the BIOS utility. Function Command Description F1 Help Gives the list of options available for each item. Shift F2 Color Change the color of the display window.
BIOS Setup Utility SY-D6IBA 31 3-1 SOYO COMBO SETUP This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP].
BIOS Setup Utility SY-D6IBA 32 3-1.1 Quick CPU Speed Settings Quick CPU Speed Settings Setting Description Note Manual 133MHz (66 x 2) 166MHz (66 x 2.5) 200MHz (66 x 3) 233MHz (66 x 3.5) 266MHz (66 x 4) 300MHz (66 x 4.5) 333MHz (66 x 5) 350MHz (100 x 3.
BIOS Setup Utility SY-D6IBA 33 3-1.2 L2 Cache Memory Setting Description Note Disabled Default CPU L2 Cache ECC Checking Enabled This option activates the CPU L2 cache ECC checking function.
BIOS Setup Utility SY-D6IBA 34 3-1.4 Power Management PM Events Setting Description Note BUTTON-ONLY Disables the Wake-Up by Keyboard function. Default KB Power ON Password Enables you to wake-up the system by entering a password at the keyboard.
BIOS Setup Utility SY-D6IBA 35 3-1.5 CPU Device Monitoring CPU Device Monitoring Setting Description Note Disabled Default CPU Warning Temperature Enabled Set CPU temperature from 50 ° C to 70 ° C. The CPU will slow down when CPU temperature goes beyond the preset value.
BIOS Setup Utility SY-D6IBA 36 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] key. This screen allows you to modify the basic CMOS settings. After you have completed the changes, press [Esc] key to return to the Main Menu.
BIOS Setup Utility SY-D6IBA 37 3-2.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary (Secondary) Master & Slave Setting Description Note Auto BIOS detects hard disk type automatically.
BIOS Setup Utility SY-D6IBA 38 3-2.4 Video Select the video mode: EGA/VGA (Default), CGA 40, CGA 80, MONO (Monochrome). 3-2.5 Halt On When the BIOS detects system errors, this function will stop the system. Select which type of error will cause the system halt: All Errors (Default), No Errors, All But Keyboard, All But Diskette, All But Disk/Key.
BIOS Setup Utility SY-D6IBA 39 3-3 BIOS FE A TURES SETUP Select the [BIOS FEATURES SETUP] option from the Main Menu and press [Enter] key. After you have completed the changes, press [Esc] key and follow the instructions on your screen to save your settings or exit without saving.
BIOS Setup Utility SY-D6IBA 40 3-3.1 Virus Warning Setting Description Note Disabled Default Virus Warning Enabled Enable this option to protect the boot sectors and partition tables of your hard disk. Any attempt to write to them will the system to halt and display a warning message.
BIOS Setup Utility SY-D6IBA 41 3-3.4 Typematic Settings Typematic Settings Setting Description Note Disabled Default Typematic Rate Setting Enabled Enables to adjust the keystroke repeat rate.
BIOS Setup Utility SY-D6IBA 42 3-3.6 Other Control Options Other Control Options Setting Description Note Disabled Default Enabled PCI/VGA Palette Snoop The color of the monitor may be altered when using an MPEG card. Enable this option to restore the monitor's normal color.
BIOS Setup Utility SY-D6IBA 43 Other Control Options (continued) Other Control Options Setting Description Note Disabled Enabled Video BIOS Shadow The BIOS is shadowed in a 16K segment if it is enabled and if it has BIOS present. These 16 segments can be shadowed from ROM to RAM.
BIOS Setup Utility SY-D6IBA 44 3-4 CHIPSET FE A TURES SETUP Caution: Change these settings only if you are already familiar with the Chipset. The [CHIPSET FEATURES SETUP] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-D6IBA 45 CHIPSET FE A TURES SETUP CHIPSET FE A TURES Setting Description Note Disabled Auto Configuration Enabled It is strongly recommended to enable this option so that the system automatically sets all chipset feature options on the left panel of the screen (except for cache update & BIOS cacheable).
BIOS Setup Utility SY-D6IBA 46 CHIPSET FE A TURES SETUP (Continued) CHIPSET FE A TURES Setting Description Note Passive Release Enabled Use the default setting Default Delayed Transaction Enabled Use the default setting Default AGP Aperture Size 64 4-256MB AGP could use the DRAM as its video RAM.
BIOS Setup Utility SY-D6IBA 47 3-5 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions. After you have completed the Power Management Setup, press [Esc] to return to the Main Menu. ROM PCI/ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC.
BIOS Setup Utility SY-D6IBA 48 3-5.1 Power Management Controls Power Management Controls Setting Description Note User Define Lets you define the HDD and system power down times.
BIOS Setup Utility SY-D6IBA 49 3-5.2 PM Timers PM Timers Setting Description Note The following [Doze Mode] field may be configured only if [Power Management] is set to [User Define] Disable Default Doze Mode 1Min- 1Hour When the set time has elapsed, BIOS sends a command to the system to enter Doze Mode.
BIOS Setup Utility SY-D6IBA 50 3-5.3 PM Events PM Events Setting Description Note Disabled Default VGA Active Monitor Enabled Enables the power management timers when a [no activity] event is detected on the monitor. Disabled Default IRQ 8 Break Suspend Enabled Alarm function is active.
BIOS Setup Utility SY-D6IBA 51 3-6 PNP/PCI CONFIGUR A TION SETUP This option sets the Motherboard's PCI Slots. Note: Starred (*) items will disappear when the [Resources Controlled By] option is set to [Auto].
BIOS Setup Utility SY-D6IBA 52 3-6.1 PNP/PCI Configuration Controls PNP/PCI Controls Setting Description Note Yes Set this field to [Yes] if you are running Windows 95/98, which are PnP compatible. PnP OS Installed No If the OS you are running does not support PnP configuration.
BIOS Setup Utility SY-D6IBA 53 3-6.2 PNP/PCI Configuration Setup PNP/PCI Setup Setting Description Note If [Resources Controlled By] is set to [Manual] PCI/ISA PnP Choose IRQ-# and DMA-# assigned to PCI/ISA PnP card.
BIOS Setup Utility SY-D6IBA 54 3-7 LOAD SETUP DEFAULTS Select the [LOAD SETUP DEFAU LTS] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
BIOS Setup Utility SY-D6IBA 55 3-8 INTEGR A TED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGRATED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-D6IBA 56 3-8.1 IDE Device Controls IDE Controls Setting Description Note Disabled IDE HDD Block Mode Enabled Invokes multi-sector transfer instead of one sector per transfer.
BIOS Setup Utility SY-D6IBA 57 3-8.3 Keyboard Controls Keyboard Controls Setting Description Note Disabled Default USB Keyboard Support Enabled Use a USB keyboard 3-8.4 Display Controls Display Controls Setting Description Note PCI Slot Default Init Display First AGP Choose which card – AGP Display card or PCI VGA card – to initialize first.
BIOS Setup Utility SY-D6IBA 58 3-8.6 Onboard Serial Ports Onboard Serial Ports Setting Description Note Disabled 3F8/IRQ4 Default (port 1) 2F8/IRQ3 Default (port 2) 3E8/IRQ4 2E8/IRQ3 Onboard Ø Serial Port 1 Ø Serial Port 2 Auto Choose serial port 1 & 2's I/O address.
BIOS Setup Utility SY-D6IBA 59 3-8.7 Onboard Parallel Ports Onboard Parallel Ports Setting Description Note 378/IRQ7 Default 3BC/IRQ7 278/IRQ5 Onboard Parallel Port Disable Choose the printer I/O address. ECP/EPP SPP Default ECP Parallel Port Mode EPP The mode depends on your external parallel device that connects to this port.
BIOS Setup Utility SY-D6IBA 60 3-9 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [BIOS FE ATURES SETUP] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: 1.
BIOS Setup Utility SY-D6IBA 61 3. Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: 4. Re-enter your password and then press [Enter] to exit to the Main Menu.
BIOS Setup Utility SY-D6IBA 62 3-11 IDE HDD AUTO DETECTION This Main Menu function automatically detects the hard disk type and configures the STANDARD CMOS SETUP accordingly.
Drivers Installation SY-D6IBA 63 Chapter 4 DRIVERS INSTALLATION Your SY-D6IBA Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your new Motherboard, the drivers software available for installation, and a database in HTML format with information on SOYO Motherboards and other products.
Drivers Installation SY-D6IBA 64 Step 2. Install Drivers Click the Install Drivers button to display the list of drivers software that can be installed with your Motherboard. The Start Up program displays the drivers available for the particular model of Motherboard you own.
Drivers Installation SY-D6IBA 65 The following drivers are available for Windows 98 (Driver Installation Menu) However, to display the list of all drivers software available with SOYO Motherboards, click the Display all drivers on the SOYO CD button.
Drivers Installation SY-D6IBA 66 Ø Intel Busmaster Drivers for Windows 95 Ø Intel Busmaster Drivers for Win NT Ø Intel Busmaster Drivers for OS/2 These are the official busmaster drivers as supplied by Intel. Note: Do NEVER install two types of busmaster drivers on your system, this will lead to conflicts and system instability.
Drivers Installation SY-D6IBA 67 Note 2: EZ-SCSI Utility: The SCSI utility for use with the onboard Adaptec ® SCSI chip is located in the driversEZ-SCSI directory. EZ- SCSI is suitable for DOS or Windows 3.1 environment only. The manual file in PDF format can be found at the following location: ManualEZ-SCSI.
Ultra SCSI I/O Subsystem SY-D6IBA 68 Chapter 5 ULTRA SCSI I/O SUBSYSTEM Note: For details on how to perform the SCSI driver installation, refer to the “ Adapte c ® 7800 Family Manager Set User ’ s Guide ” included on the Installation CD-ROM that comes with your Motherboard.
Ultra SCSI I/O Subsystem SY-D6IBA 69 5-2 INSTALLING SCSI DEVICES Your Motherboard features two internal SCSI connectors onboard, and comes with one 50-pin and one 68-pin flat cables. 5-2.1 50-pin Fast SCSI Connector Narrow SCSI bus allows data transfer rates of up to 20 Mbytes/sec.
Ultra SCSI I/O Subsystem SY-D6IBA 70 5-3 CONNECTING INTERNAL SCSI DEVICES If you are connecting several internal SCSI devices (more than 2 CD-ROM drives), make sure you have an internal SCSI cable with enough connectors to accommodate all of your devices.
Ultra SCSI I/O Subsystem SY-D6IBA 71 5-4 ADAPTEC RAIDPOR T ™ The onboard Adaptec RAIDpor t ™ slot is designed to provide embedded SCSI solutions to your Motherboard. To use this RAIDport solutions, plug the Adaptec AR O ™ - 1130 RAIDpor t ™ card into RAIDport slot on the Motherboard.
72.
Een belangrijk punt na aankoop van elk apparaat SOYO SY-D6IBA (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen SOYO SY-D6IBA heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens SOYO SY-D6IBA vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding SOYO SY-D6IBA leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over SOYO SY-D6IBA krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van SOYO SY-D6IBA bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de SOYO SY-D6IBA kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met SOYO SY-D6IBA . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
