Gebruiksaanwijzing /service van het product DS06 van de fabrikant Stanley Black & Decker
Ga naar pagina of 33
DS06 HYDRAULIC DIAMOND SA W S AFETY , O PERA TION AND M AINTENANCE SER VICE MANUAL WARNING Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .
.
3 T ABLE OF CONTENTS For the nearest authorized and certifi ed dealer , call Stanley Hydraulic T ools at the number listed on the back of this manual and ask for a Customer Service Representative. SERVICING THE ST ANLEY CONCRETE CHAINSA W: This manual contains safety , operation, and routine maintenance instructions.
4 CERTIFICATE OF CONFORMITY ÜBEREINSTIMMUNGS-ZERTIFIKAT CERTIFICAT DE CONFO RMITE CEE CERTIFICADO DE CONFORMI DAD CERTIFICATO DI CONFO RMITA Hy draulic Tools ______________________________________________________________________ I, the undersigned: Ich, der Unterzeichnende: Je soussigné: El abajo firmante: lo sottoscritto: Schultz, Theodore J.
5 Safety symbols and signal words, as shown below , are used to emphasize all operator , maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip- ment.
6 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Review them carefully before operating the tool and before performing general maintenance or repairs.
7 • Remove or control the water slurry to prevent yourself or others from slipping while cutting. • Provide adequate ventilation in closed areas when operating a gas or diesel hydraulic power source. • Always be well rested and mentally alert before operating the chain saw .
8 The safety tag (p/n 15875) at right is attached to the tool when shipped from the factory . Read and understand the safety instructions listed on this tag before removal.
9 HOSE TYPES Hydraulic hose types authorized for use with Stanley Hydraulic T ools are as follows: ➊ Certifi ed non-conductive ➋ Wire-braided (conductive) ➌ Fabric-braided (not certifi ed or labeled non-conductive) Hose ➊ listed above is the only hose authorized for use near electrical conductors.
10 HTMA REQUIREMENTS FLOW RA TE TOOL OPERA TING PRESSURE (at the power supply outlet) SYSTEM RELIEF V AL VE SETTING (at the power supply outlet) MAXIMUM BACK PRESSURE (at tool end of the return hose) Measured at a max. fl uid viscosity of: (at min. operating temperature) TEMPERA TURE Suffi cient heat rejection capacity to limit max.
11 PREOPERTION PROCEDURES CHECK THE POWER SOURCE 1. Using a calibrated fl ow meter and pressure gauge, make sure the hydraulic power source develops a fl ow of 7-9 gpm/26-34 lpm for the 8 gpm model and 4-6 gpm/15-23 lpm for the 5 gpm model at 2000 psi/140 bar .
12 2. Make sure the bar attaching nuts are fully tightened and the chain guard is in place. Figure 2. Maximum Chain Clearance CHECK CHAIN SEGMENT WEAR 1. Using adjustable calipers, measure several chain seg- ments as illustrated in Figure 3. Figure 3.
13 TYPES OF CUTS The DS06 can be operated using the types of cuts shown in Figure 5. When making cuts: Figure 5. T ypes of Cuts (chain guard removed for clarity) 1. Do not use a cutting force in excess of 45 lbs/20 kg. Excessive force causes the chain to slow down or stall and causes premature wear of the saw bar and chain.
14 CHAIN TENSION ADJUSTMENT Correct chain tension is very important throughout the life of the chain. Check the chain tension often during use (when the chain saw is stopped and the saw bar and chain have cooled off). The chain should move easily around the saw bar when pulled by hand.
15 Figure 13. Inserting the Chain 3. Position the rivet head you want removed directly under the chainbreaker punch and then pull the handle down far enough to remove the rivet (Figure 14). Do not use exces- sive force. Figure 14. Removing a Rivet Figure 10.
16 REPLACING THE CHAIN BREAKER PUNCH If the chain breaker punch (part number 22801) becomes worn or damaged, use the following prcedures for replace- ment. 1. Remove the punch by loosening the set screw (Figure 15). Figure 15. Removing the Punch 2. Insert a new punch into the holder and push it up until it is fully seated (Figure 16).
17 4. turn the rivet spinner crank a few times to center the rivet hub in the spinner anvil (Figure 20). Figure 20. Centering the Rivet Hub 5. Apply a few drops of oil to the rivet hub (Figure 21).
18 MAINTENANCE & ADJUSTMENTS Figure 25. Removing Old Nose Sprocket 3. Remove the new nose sprocket package's clips and fold back the top portion of the insertion card being careful not to remove or disturb the components. See Figure 26. Figure 26.
19 T OOL EQUIPMENT & CARE • Make sure all couplers are wiped clean before connection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hydraulic system.
20 TROUBLESHOOTING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the tool, always check that the hydraulic power source is supplying the correct hydraulic fl ow and pressure to the tool as listed in the table.
21 TROUBLESHOOTING SYMPTOM CAUSE REMEDY Leakage around drive sprocket. Motor shaft seal failure. Have unit serviced. No water discharge at bar . Blocked port(s) in bar . T urn off hydraulic supply . Remove bar and chain and clean bar thoroughly . Blow ports with compressed air .
22 SPECIFICA TIONS Cutting Depths ................................................................................................................ ............................ 13 inches / 33 cm Bar Lengths .............................................
23 SER VICE INSTRUCTIONS PRIOR T O DISASSEMBL Y Clean exterior of the tool. Obtain a seal kit so that all seals exposed during disas- sembly can be replaced. ON-OFF V AL VE SERVICING TRIGGER (28) AND SAFETY CA TCH (30) REMOV AL & INST ALLA TION 1.
24 SER VICE INSTRUCTIONS MOT OR SERVICING 1. Remove the 2 nuts (51) and then lift off the chain guard (50). 2. Lift off the bar (61) and chain (73). If it is necessary to take tension off the bar and chain, turn the screw (68) counter clockwise. For Diamond Saws with Serial Number 357 and above, follow the steps a thru c, then proceed to Step 7.
25 SER VICE INSTRUCTIONS groove should be smooth as should the rest of the fl at surface. The bore for the shaft seal should be smooth or oil leakage may occur . GEAR HOUSING Shake the gear housing and the two seal check balls (not shown) should rattle.
26 SER VICE INSTRUCTIONS For Diamond Saws with Serial Number 357 and above follow steps a thru e. For Diamond Saws with Serial Number 356 and below , follow steps 10 thru 13. a. Install the o-ring (43). Push in until it contacts the bearing face. b. Install seal washer (94) and the retainer ring (98).
27 DS06 P ARTS ILLUSTRA TION For Serial Numbers 357 and Above. 54 99.
28 DS06 P ARTS LIST Item No. Part No. Qty Description 1 00753 8 HSHCS 10-24 UNC x 1-1/4 2 33445 1 Name T ag 3 11 2 0 7 11 2 0 6 1 Circuit “D” Decal (8 gpm Model) Circtuit “C” Decal (5 gpm Model) 4 07652 1 Rear Gear Housing Assy . (Incl. Items 5-6), 8 gpm Model Only 07834 1 Rear Gear Housing Assy .
29 DS06 P ARTS ILLUSTRA TION For Serial Numbers 356 and Below ..
30 DS06 P ARTS LIST For Serial Numbers 356 and Below . • Denotes Part in Seal Kit Item Qty Part Description No No. Item Qty Part Description No No. 1 8 00753 HSHCS 10-24UNCx1-1/4 2 1 33445 NAME T AG.
31 DIAMOND CHAIN APPLICA TIONS Model Bar Length P/N Correct Applications Ultra- Ultra- Pinnacle- Pinnacle- 13 inch V ery hard aggregate concretes (fl int, chert, granite, etc). Heavy steel reinforcing, 5/8 inch/16 mm diameter and larger . Medium/hard aggre- gate concretes (granite, quartz, river rock, etc).
32 Stanley Hydraulic T ools (hereinafter called “Stanley”), subject to the exceptions contained below , warrants new hydraulic tools for a period of one year from the date of sale to the fi rst r.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .stanley-hydraulic-tools.com.
Een belangrijk punt na aankoop van elk apparaat Stanley Black & Decker DS06 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Stanley Black & Decker DS06 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Stanley Black & Decker DS06 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Stanley Black & Decker DS06 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Stanley Black & Decker DS06 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Stanley Black & Decker DS06 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Stanley Black & Decker DS06 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Stanley Black & Decker DS06 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
