Gebruiksaanwijzing /service van het product TCP300 Series van de fabrikant Star Micronics
Ga naar pagina of 16
THERMAL RE-WRIT ABLE CARD READER / WRITER T CP300 SERIES • User ’ s Manual • This ‘User ’s Manual’ describes important information to enable you to use the reader/writer safely . Carefully read this manual before using the reader/writer and observe the descriptions herein.
Federal Communications Commission Radio Frequency Interfer ence Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
– 1 – 1. Precautions for Safe Use Carefully read and obey the following items to prevent injury to yourself or to others and to prevent damaging property . Precautions for Reader/Writer Setup 1. Setup the reader/writer in a solid, and level location.
– 2 – Precautions for Reader/Writer Use 1. Use only Star recommended cards. The reader/writer and the card may not operate normally if other cards are used. 2. Do not use cards that are dirty or oily or wet in any other manner . Also, do not handle cards with dirty or wet hands.
– 3 – 10. In case of reader/writer error (abnormal sounds, abnormal odors, smoke, fire) turn off the reader/writer immediately and unplug it from the power outlet. 1 1. Always hold the plug to unplug the power cord from its outlet. Pulling on the cord will damage the cord.
– 4 – 2. General Description The TCP300 series reader/writers are equipped with a thermal type display mechanism on a PET(Polyethyleneterephtalate) magnetic strip card reader/writer . They are con- nected to electrical devices such as POS and are used to print/erase characters and images freely onto the surface of cards.
– 5 – 3. Unpacking The following outlines the reader/writer and its accessories. The reader/writer (TCP300 Series) 1. Reader/writer 2. Cleaning cards (2 cards) 3.
– 6 – 4. External Appearance and Part Names The reader/writer (TCP300 Series) 1. Power Switch ............................ This turns the power to the reader/writer on and off. 2. Power Indicator Lamp .............. Indicates that reader/writer power is on.
– 7 – 5. Connect to and Setting External Devices 5-1 RS-232C Interface <Mounting the RS-232C Interface Cable> 1. Cut the power to the host computer and reader/writer . 2. Connect one end of the interface cable to the reader/writer and the other end to the host computer .
– 8 – <Settings for Communication Speed> T o change the serial communication settings, change the following DIP switch settings. (Ex-factory Default Settings: DSW 1 to 6 are ON, 7 and 8 are OFF .
– 9 – 5-2 USB Interface <Mounting the USB Interface Cable> 1. Connect one end of the interface cable to the reader/writer and the other end to the host computer .
– 10 – 6. Interface Board Replacement (RS-232C to USB) Replacement Procedures 1. T urn off the power switch. Then, unplug the power cord from the outlet. 2. Remove the two screws as shown in the figure below . 3. Pull the RS-232C interface board in the direction of the arrow to remove it.
– 11 – 7. Cleaning Cards A cleaning card is used to clean the transport rollers inside the unit. T wo cleaning cards accompany each unit. They are in the plastic wrap. 7-1 External Shape 7-2 Frequency of Use 1. Everyday , or once every 300 prints.
– 12 – 8. T roubleshooting • T rouble when T urning on the Power Symptom Possible Cause What to Do The power indicator Won’t accept The power plug is not Correct connect the power lamp does not light. cards. correctly connected. plug. Broken wire in power cord.
– 13 – • Removing Jammed Cards 1. T urn off the power and unplug the reader/writer . 2. Press the cover opener . 3. Lift the upper cover while the cover is open. 4. While pulling the mechanism’s snap lever (green), lift the mechanism. 5. Remove the card while the cover is open.
– 14 – 9. General Specifications Item Specifications Card Specification PET (Thin type card) Card T ransport Unit T ransport Method Rollers Card Insertion Direction One Direction Card T ravel Spee.
Een belangrijk punt na aankoop van elk apparaat Star Micronics TCP300 Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Star Micronics TCP300 Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Star Micronics TCP300 Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Star Micronics TCP300 Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Star Micronics TCP300 Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Star Micronics TCP300 Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Star Micronics TCP300 Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Star Micronics TCP300 Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
