Gebruiksaanwijzing /service van het product TSP700 van de fabrikant Star Micronics
Ga naar pagina of 116
THERMAL PRINTER TSP700 SERIES USER’S MANU AL MODE D’EMPLOI BEDIENUNGSANLEITUNG MANU ALE DI ISTR UZIONI.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
T ABLE OF CONTENTS 1. Parts Identification and Nomenclature ......................................................... 1 2. Consumable Parts and AC Adapter .............................................................. 3 3. Connecting Cables and AC Adapter .
– 1 – ENGLISH 1. Parts Identification and Nomenclature Roll paper User’s manual Cover open lever Pull this lever in the direction of the arrow to open the printer cover. Control panel Features LED indica- tors to indicate printer status and switches to operate the printer.
– 2 – ENGLISH Choosing a place for the printer Before actually unpacking the printer, you should take a few minutes to think about where you plan to use it. Remember the following points when doing this. ✓ Choose a firm, level surface where the printer will not be exposed to vibration.
– 3 – ENGLISH 2. Consumable Parts and AC Adapter When consumable parts have run out, use those specified in the table below. Make sure that the AC adapter specified in the table is used. Use of consumable parts or AC adapter which are not specified in the table may result in damage to the printer, fire or electric shock.
– 4 – ENGLISH Kanzaki Speciality Papers Inc. (KSP) P320RB (2 color paper: Red & Black), 65 µ m (thickness) P320BB (2 color paper: Blue & Black), 65 µ m (thickness) Depending on the type and thickness of the paper, it may be necessary to change the settings for printing darkness.
– 5 – ENGLISH 3. Connecting Cables and AC Adapter Serial interface cable 3-1. Interface Cable Note that the interface cable is not provided. Please use a cable that meets specifications. CAUTION Before connecting/disconnecting the interface cable, make sure that power to the printer and all the devices connected to the printer is turned off.
– 6 – ENGLISH 3-1-2. Parallel Interface Cable (1) Make sure the printer is turn off. (2) Affix the ferrite core onto the cable as shown in the illustration. (3) Pass the fastener through the ferrite core. (4) Loop the fastener around the cable and lock it.
– 7 – ENGLISH (5) Connect the interface cable to the connector on the rear panel of the printer. (6) Fasten the connector clasps. Parallel interface cable 3-1-3.
– 8 – ENGLISH 3-1-4. Connecting Ethernet Cable (1) Make sure the printer is turned off. ( 2 ) Affix the ferrite core onto the ethernet cable as shown in the illus- tration below. (3) Pass the fastener through the ferrite core. (4) Loop the fastener around the cable and lock it.
– 9 – ENGLISH 3-2. Connecting to a Peripheral Unit You can connect a peripheral unit to the printer using a modular plug. The following describes how to install the ferrite core and make the actual connection. See “ Modular plug ” on page 109 for details about the type of modular plug that is required.
– 10 – ENGLISH 3-3. Connecting the Optional AC Adapter Note: Before connecting/disconnecting the AC adapter, make sure that power to the printer and all the devices connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC outlet.
– 11 – ENGLISH Power switch 3-4. T urning Power On Make sure that the AC adapter has been connected as described in 3-3. (1) Set the power switch located on the front of the printer to on.
– 12 – ENGLISH 4. Control Panel and Other Functions 4-1. Control Panel 1 POWER lamp (Green LED) Lights when the power is ON 2 ERROR lamp (Red LED) Indicates various errors in combi- nation with POWER lamp 3 FEED button Press the FEED button to feed roll paper.
– 13 – ENGLISH 3) Non recoverable error Note 1) If a non recoverable error occurs, turn the power OFF immediately. 2) When Power supply error occurs, there is a possibility that the power supply unit has a trouble. For other non recoverable errors, please consult the dealer for repairs.
– 14 – ENGLISH 4-3. Self Printing (1) Test Printing Turn the power on while holding the FEED button depressed. Test printing will be performed according to the Ver. No., DIP switch settings and character order. When the FEED button is depressed at the time of the end of test printing, only the characters will be printed out repeatedly.
– 15 – ENGLISH 5. Loading the Roll Paper Be sure to use roll paper that matches the printer ’ s specification. When using a paper roll with an 82.5 mm width, remove the paper roll holder as described on the following page. Push the Cover open lever, and open the printer cover.
– 16 – ENGLISH Note 2: When using paper with a thick- ness which does not require the use of the tension bar (100 µ m paper thick- ness 150 µ m), remove the tension bar unit by removing the clips at both ends of the bar with a flat head screwdriver.
– 17 – ENGLISH Important! 1. Do not touch the cutter blade. · There is a cutter inside the paper outlet slot. Not only should you not put your hand in the paper outlet slot while printing is in progress, never put your hand into the outlet even when printing is not in progress.
– 18 – ENGLISH 6. Adjusting the Near-end Sensor Use the following procedure to adjust the near-end sensor so it is compatible with the size of roll paper you are using. 1 Open the printer cover. 2 Determine the diameter of the roll paper you are using and find the required setting in the table below.
– 19 – ENGLISH Adjustment value according to the paper you are using Note 1) The standard model is set to level 1 prior to being shipped from the fac- tory. 2) The C dimension and the remained paper length are the calculated val- ues. There may be some variations in actual mechanism.
– 20 – ENGLISH 7. Preventing and Clearing Paper Jams 7-1. Pr eventing Paper Jams The paper should not be touched during ejection and before it is cut. Pressing or pulling the paper during ejection may cause a paper jam, paper cutting failure or line feed failure.
– 21 – ENGLISH 8. Periodical Cleaning Printed characters may become partially unclear due to accumulated paper dust and dirt. To prevent such a problem, paper dust collected in the paper holder and paper transport section and on the surface of the thermal head must be removed periodically.
– 22 – FRANÇAIS T ABLE DES MA TIERES 1. Identification des pièces et nomenclature .................................................... 23 2. Consommables et adaptateur secteur .......................................................... 25 3. Câbles de connexion et adaptateur secteur .
– 23 – FRAN Ç AIS 1. Identification des pièces et nomenclature Rouleau de papier Mode d ’ emploi Capot de l ’ imprimante Ouvrez ce capot pour charger ou remplacer le papier. Interrupteur d ’ alimentation Permet la mise sous et hors tension de l ’ appareil.
– 24 – FRAN Ç AIS Emplacement de l ’ imprimante Avant de d é baller l ’ imprimante, d é terminez l ’ emplacement o ù vous souhaitez l ’ installer. Veuillez observer les points ci-dessous lors de votre choix. ✓ Choisissez une surface stable et de niveau sur laquelle l ’ imprimante ne sera expos é e à aucune vibration.
– 25 – FRAN Ç AIS 2. Consommables et adaptateur secteur Il convient d ’ utiliser exclusivement les types de papier figurant dans le tableau ci- dessous.
– 26 – FRAN Ç AIS Kanzaki Speciality Papers Inc. (KSP) P320RB (papier 2 couleurs : rouge et noir), 65 µ m ( é paisseur) P320BB (papier 2 couleurs : bleu et noir), 65 µ m ( é paisseur) Suivant le type et l ’é paisseur du papier, il peut ê tre n é cessaire de changer le r é glage de clart é d ’ impression.
– 27 – FRAN Ç AIS 3. C â bles de connexion et adaptateur secteur C â ble d ’ interface s é rie 3-1. C â ble d ’ interface Le c â ble d ’ interface n ’ est pas livr é .
– 28 – FRAN Ç AIS 3-1-2. Interface parall è le (1) Assurez-vous que l ’ imprimante est hors tension. (2) Fixez la grande gaine en ferrite sur le c â ble comme illustr é . (3) Passez l ’ attache dans le tore de fer- rite. (4) Passez l ’ attache autour du tore de ferrite et serrez-la.
– 29 – FRAN Ç AIS (5) Connectez le c â ble d ’ interface à la borne figurant sur le panneau arri è re de l ’ imprimante. (6) Attachez les fermoirs du connecteur.
– 30 – FRAN Ç AIS 3-1-4. Branchement d ’ un c â ble ethernet (1) Assurez-vous que l ’ imprimante est hors tension. (2) Attachez le tore de ferrite au c â ble ethernet conform é ment à l ’ illustra- tion. (3) Passez le collier de serrage par le tore de ferrite.
– 31 – FRAN Ç AIS 3-2. Raccordement d ’ un appareil p é riph é rique Vous pouvez raccorder un appareil p é riph é rique à l ’ imprimante à l ’ aide d ’ une fiche modulaire. Nous expliquons ci-dessous comment installer le tore de ferrite et faire le raccordement proprement dit.
– 32 – FRAN Ç AIS 3-3. Connexion de l ’ adaptateur secteur optionnel Remarque: Avant de connecter ou d é connecter l ’ adaptateur secteur, veillez à ce que l ’ imprimante et tous les appareils qui y sont connect é s soient hors tension. Veillez é galement à d é brancher le c â ble d ’ alimentation de la prise secteur.
– 33 – FRAN Ç AIS 3-4. Mise sous tension de l ’ imprimante Assurez-vous d ’ avoir bien connect é l ’ adaptateur secteur comme d é crit à la section 3-3. (1) Placez l ’ interrupteur d ’ alimentation, situ é à l ’ avant de l ’ imprimante, sur la position sous tension.
– 34 – FRAN Ç AIS 4-1. Panneau de commande 1 T é moin POWER (DEL verte) S ’ allume quand l ’ appareil est sous tension. 2 T é moin ERROR (DEL rouge) Indique des erreurs vari é es en com- binaison avec le t é moin POWER. 3 T é moin FEED Appuyez sur la touche FEED pour faire avancer le papier.
– 35 – FRAN Ç AIS 3) Erreur non r é cup é rable Remarque 1) Si une erreur non r é cup é rable se produit, mettez imm é diatement l ’ appareil hors tension. 2) Quand une erreur d ’ alimentation se produit, il est possible que le bloc d ’ alimentation soit en panne.
– 36 – FRAN Ç AIS 4-3. Auto-impression (1) Essai d ’ impression Mettez l ’ appareil sous tension tout en maintenant la touche FEED enfonc é e. L ’ essai d ’ impression sera effectu é en fonction du num é ro de version, des r é glages du commutateur DIP et de l ’ ordre des caract è res.
– 37 – FRAN Ç AIS 5. Chargement du rouleau de papier Veillez à utiliser un rouleau de papier qui correspond aux sp é cifications de l ’ imprimante. Lors de l ’ utilisation d ’ un rouleau de papier de 82,5 mm de large, d é posez le support du rouleau de papier comme expliqu é à la page suivante.
– 38 – FRAN Ç AIS Support du rouleau de papier Remarque 2: Quand vous utilisez un papier dont l ’é paisseur (entre 100 µm et 150 µm) ne n é cessite pas l ’ utilisation de la barre de tension, enlevez la barre de tension en retirant les clips aux deux extr é mit é s de la barre, à l ’ aide d ’ un tournevis plat.
– 39 – FRAN Ç AIS Poussez vers la bas les deux c ô t é s du capot de l ’ imprimante pour le fermer. Remarque: Assurez-vous que le capot de l ’ imprimante est bien ferm é . Attention! 1. Ne pas toucher la lame du coupe-ruban. · Une lame se trouve dans la fente de sortie de papier.
– 40 – FRAN Ç AIS 6. R é glage du capteur de fin de rouleau Utilisez la proc é dure suivante pour r é gler le capteur de fin de rouleau conform é - ment à la taille du rouleau de papier utilis é .
– 41 – FRAN Ç AIS Valeur de r é glage correspondant au papier utilis é . Remarque 1) Le curseur de r é glage du mod è le standard est r é gl é sur le niveau 1 en usine. 2) La dimension C et la longueur de papier restante sont les valeurs cal- cul é es.
– 42 – FRAN Ç AIS 7. Pr é vention et correction de bourrages de papier 7-1. Pr é vention des bourrages de papier Il convient de ne jamais toucher le papier pendant son é jection et avant qu ’ il soit coup é .
– 43 – FRAN Ç AIS 8. Nettoyage Les caract è res imprim é s pourraient devenir partiellement illisibles en raison de l ’ accumulation de la poussi è re de papier et de crasse.
– 44 – DEUTSCH INHAL TSVERZEICHNIS 1. Beschreibung und Bezeichnung der Geräteteile ......................................... 45 2. Verbrauchsteile und Netzteil ........................................................................ 47 3. Anschlußkabel und Netzteil .
– 45 – DEUTSCH 1. Beschreibung und Bezeichnung der Geräteteile Rollenpapier Bedienungsanleitung Abdeckung-öffnen-Hebel Diesen Hebel in Pfeilrichtung ziehen, um die Druckerabdeckung zu öffnen. Bedienfeld Mit LED-Anzeigen zur Anzeige des Druckerstatus und Schalter zur Druckerbedienung.
– 46 – DEUTSCH W ahl eines Aufstellungsorts f ü r den Drucker Bevor Sie den Drucker auspacken, sollten Sie einige Minuten damit verbringen, einen geeigneten Aufstellungsort auszusuchen. Denken Sie dabei an die folgenden Punkte: ✓ Den Drucker auf einem flachen, aber festen Untergrund aufstellen, wo keine Vibrationen vorhanden sind.
– 47 – DEUTSCH Wenn die Verbrauchsteile verbraucht sind, besorgen Sie Ersatz entsprechend der unten gezeigten Tabelle. Verwendung von Verbrauchsteilen oder Netzteilen, die nicht den unten aufge- f ü hrten Beschreibungen entsprechend, kann zu Sch ä den am Drucker, Br ä nden oder elektrischen Schl ä gen f ü hren.
– 48 – DEUTSCH Nippon Paper Industries TF50KS-E2C (Normalpapier), 65 µ m (Dicke) Kanzaki Specialty Papers Inc. (KSP) P320RB (Bicolor-Papier: Rot & Schwarz), 65 µ m (Dicke) P320BB (Bicolor-Pa.
– 49 – DEUTSCH 3. Anschlu ß kabel und Netzteil Serielles Schnittstellenkabel 3-1. Schnittstellenkabel Beachten Sie, da ß das Schnittstellenkabel nicht mitgeliefert ist.
– 50 – DEUTSCH 3-1-2. Parallele Schnittstelle (1) Stellen Sie sicher, da ß der Drucker ausgeschaltet ist. (2) Befestigen Sie den gro ß en Ferrit- kern am Kabel, wie das in der Ab- bildung gezeigt wird. (3) F ü hren Sie den Kabelbinder durch den Ferritkern.
– 51 – DEUTSCH (5) Schlie ß en Sie das Schnittstellenkabel an die Buchse an der R ü ckseite des Druckers an. (6) Befestigen Sie die Steckerklammern.
– 52 – DEUTSCH 3-1-4. Anschlie ß en des Ethernet-Kabels (1) Stellen Sie sicher, da ß der Drucker ausgeschaltet ist. (2) Bringen Sie den Ferritkern auf dem Ethernet-Kabel an, wie in der Ab- bildung unten gezeigt. (3) F ü hren Sie die Befestigung durch den Ferritkern.
– 53 – DEUTSCH 3-2. Anschlu ß an ein Peripherieger ä t Es kann ein Peripherieger ä t an den Drucker mit einem Modularstecker ange- schlossen werden. Im folgenden wird beschrieben, wie der Ferritkern angebracht und die Verbindung hergestellt wird.
– 54 – DEUTSCH 3-3. Anschlie ß en des optionalen Netzteils Hinweis: Vor dem Anschlie ß en/Abtrennen des Netzteils stellen Sie sicher, da ß der Drucker und alle angeschlossenen Ger ä t ausgeschaltet sind. Au ß erdem sollte der Netzstecker abgezogen sein.
– 55 – DEUTSCH 3-4. Einschalten Stellen Sie sicher, da ß das Netzteil angeschlossen ist, wie in 3-3 beschrieben. (1) Den Netzschalter vorne am Ger ä t auf Ein (ON) stellen.
– 56 – DEUTSCH 4. Bedienfeld und andere Funktionen 4-1. Bedienfeld 1 POWER-L ä mpchen (gr ü ne LED) Leuchtet in eingeschaltetem Zustand 2 ERROR-L ä mpchen (rote LED) Zeigt in Kombination mit dem PO- WER-L ä mpchen verschiedene Fehlerzust ä nde an 3 FEED-Taste Die FEED-Taste dr ü cken, um das Rollenpapier vorzutransportieren.
– 57 – DEUTSCH 3) Nicht behebbare Fehler Hinweis 1) Wenn ein nicht behebbarer Fehler auftritt, das Ger ä t sofort ausschalten. 2) Wenn ein Stromversorgung-Fehler auftritt, besteht die M ö glichkeit, da ß die Netzversorgung nicht richtig ist.
– 58 – DEUTSCH 4-3. Selbstdruck (1) Testdruck Das Ger ä t einschalten, w ä hrend die FEED-Taste gedr ü ckt gehalten wird. Der Testdruck wird entsprechend der Ver.
– 59 – DEUTSCH 5. Einlegen der Papierrolle Immer Rollenpapier verwenden, das zu den technischen Daten des Druckers pa ß t. Bei Verwendung einer Papierrolle mit einer Breite von 82,5 mm den Papierrollen- halter, wie auf der folgenden Seite beschrieben, entfernen.
– 60 – DEUTSCH Hinweis 2: Bei Verwendung von Pa- pier mit einer St ä rke, die den Einsatz der Spannstange nicht erforderlich macht (Papierst ä rke 100µm und 150 µm), die Spannstange abnehmen. Dazu die Klammern an beiden Enden der Stange mit einem Flachkopf- schraubenzieher abnehmen.
– 61 – DEUTSCH Beide Seiten der Druckerabdeckung zum Schlie ß en nach unten dr ü cken. Hinweis: Sicherstellen, da ß die Druckerabdeckung fest geschlossen ist. Wichtig! 1. Nicht die Schneidwerkklinge ber ü hren. · Im Papierausla ß schlitz befindet sich ein Schneidwerk.
– 62 – DEUTSCH 6. Einstellung des Endan ä herungs-Sensors Den Endan ä herungs-Sensor auf folgende Weise justieren, damit er der Gr öß e der verwendeten Papierrolle entspricht. 1 Die Druckerabdeckung ö ffnen. 2 Den Durchmesser der verwendeten Papierrolle ermitteln, und in der untenste- henden Tabelle die entsprechende Einstellung aufsuchen.
– 63 – DEUTSCH Einstellwerte entsprechend des verwendeten Papiers Hinweis 1) Das Standardmodell ist werkseitig auf Niveau 1 gestellt. 2) Die Abmessung C und die restliche Papierl ä nge sind berechnete Werte. Es k ö nnen leichte Abweichungen zum tats ä chlichen Wert auftreten.
– 64 – DEUTSCH 7. V erhindern und Beheben von Papierstau 7-1. V er hindern von Papierstau Das Papier soll beim Ausgeben und vor dem Schneiden nicht ber ü hrt werden. Wenn das Papier beim Ausgeben gedr ü ckt oder gezogen wird, kann ein Papiers- tau, ein Abschneidfehler oder ein Zeilenvorschubfehler verursacht werden.
– 65 – DEUTSCH 8. Regelm äß ige Reinigung Die Druckzeichen k ö nnen durch Ansammlung von Papierstaub und anderem Schmutz unscharf werden. Um das zu verhindern, mu ß im Papierhalter und in der Papiertransportstufe angesammelter Staub von Zeit zu Zeit entfernt werden.
– 66 – ITALIANO INDICE 1. Identificazione delle parti e nomenclatura .................................................. 67 2. Parti soggette a consumo e trasformatore CA ............................................ 69 3. Cavi di collegamento e trasformatore CA .
– 67 – ITALIANO 1. Identificazione delle parti e nomenclatura Carta in rotolo Manuale dell’utilizzatore Pannello di controllo Dispone di indicatori LED che indicano lo stato della stampante e di interruttori per controllare la stampante. Connettore di alimentazione Per il collegamento del trasformatore CA.
– 68 – ITALIANO Scelta di un luogo per la stampante Prima di disimballare la stampante, decidere dove si desidera installarla. Tenere presenti i seguenti punti. ✓ Scegliere una superficie stabile e in piano, dove la stampante non sia esposta a vibrazioni.
– 69 – ITALIANO 2. Parti soggette a consumo e trasformatore CA Quando le parti soggette a consumo si sono esaurite, usare quelle specificate nella seguente tabella.
– 70 – ITALIANO Kanzaki Speciality Papers Inc. (KSP) P320RB (carta bicolore: rosso e nero), 65 µ m (spessore) P320BB (carta bicolore: blu e nero), 65 µ m (spessore) A seconda del tipo e dello spessore della carta, pu ò essere necessario cambiare le impostazioni per la densit à di stampa.
– 71 – ITALIANO 3. Cavi di collegamento e trasformatore CA Cavo interfaccia seriale 3-1. Cavo interfaccia Notare che il cavo interfaccia non è in dotazione.
– 72 – ITALIANO 3-1-2. Interfaccia parallelo (1) Assicurarsi che la stampante sia spenta. (2) Fissare l ’ anello di ferrite al cavo come mostrato nell ’ illustrazione. (3) Far passare la fascetta di fissaggio attraverso l ’ anello di ferrite.
– 73 – ITALIANO (5) Collegare il cavo interfaccia al connettore sul pannello posteriore della stampante. (6) Fissare i morsetti del connettore. Cavo interfaccia parallelo 3-1-3.
– 74 – ITALIANO 3-1-4. Collegamento del cavo Ethernet (1) Assicurarsi che la stampante sia spenta. (2) Applicare l ’ anello di ferrite al cavo Ethernet come mostrato nell ’ illu- strazione sotto. (3 ) Far passare il fermo attraverso l ’ anello di ferrite.
– 75 – ITALIANO 3-2. Collegamento ad un’unità periferica Si pu ò collegare un ’ unit à periferica alla stampante usando una spina modulare. Di seguito descriviamo come installare l ’ anello di ferrite ed eseguire il collega- mento. Vedere “ Modulare necessario ” a pagina 109 per dettagli sul tipo di spina modulare necessario.
– 76 – ITALIANO 3-3. Collegamento del trasformator e CA opzionale Nota: Prima di collegare/scollegare il trasformatore CA, assicurarsi che la stampante e tutti i dispositivi collegati alla stampante siano spenti. Inoltre assicurarsi che la spina del cavo di alimentazione sia scollegata dalla presa di corrente.
– 77 – ITALIANO 3-4. Accensione Assicurarsi che il trasformatore CA sia stato collegato come indicato nella sezione 3-3. (1) Regolare su ON l ’ interruttore di alimentazione situato sul davanti della stampante. La spia POWER sul pannello di controllo si illumina.
– 78 – ITALIANO 4. Pannello di controllo e altre funzioni 4-1. Pannello di controllo 1 Spia POWER (LED verde) Si illumina quando l ’ unit à è accesa. 2 Spia ERROR (LED rosso) Indica vari errori in combinazione con la spia POWER. 3 Tasto FEED Premere il tasto FEED per far avan- zare la carta su rotolo.
– 79 – ITALIANO 3) Errori senza recupero Nota 1) Se si verifica un errore senza recupero, spegnere immediatamente l ’ unit à . 2) Quando si verifica un errore alimentazione, esiste la possibilit à che l ’ unit à di alimentazione sia guasta.
– 80 – ITALIANO 4-3. Stampa automatica (1) Stampa di prova Accendere l ’ unit à tenendo premuto il tasto FEED. La stampa di prova viene eseguita nell ’ ordine di numero di versione, impostazioni degli interruttori DIP e ordine dei caratteri.
– 81 – ITALIANO 5. Inserimento del rotolo di carta Assicurarsi di usare carta su rotolo che corrisponde alle specifiche della stampan- te. Quando si usa un rotolo di carta della larghezza di 82,5 mm, rimuovere il supporto del rotolo di carta come descritto nella pagina seguente.
– 82 – ITALIANO Supporto del rotolo di carta Nota 2: Quando si usa carta di uno spessore che non richiede l ’ uso della barra di tensione (100 µm spessore carta 150 µm), rimuovere con un cacciavite a testa piatta le graffette si- tuate ad entrambe le estremit à della barra di tensione per rimuovere la barra stessa.
– 83 – ITALIANO Premere su entrambi i lati del coper- chio stampante per chiudere. Nota: Assicurarsi che il coperchio stam- pante sia saldamente chiuso. Importante! 1. Non toccare la lama della taglierina. · All ’ interno della fessura di uscita carta si trova una taglierina.
– 84 – ITALIANO 6. Regolazione del sensore di esaurimento prossimo Usare il seguente procedimento per regolare il sensore di esaurimento prossimo in modo che sia compatibile con le dimensioni del rotolo di carta usato. 1 Aprire il coperchio stampante.
– 85 – ITALIANO Valore di regolazione secondo la carta usata Nota 1) Il modello standard è impostato sul livello 1 prima di uscire dalla fabbrica. 2) La dimensione C e la lunghezza di carta rimanente sono valori calcola- ti. Si possono avere leggere varia- zioni nell ’ uso effettivo.
– 86 – ITALIANO 7. Prevenzione e soluzione degli inceppamenti della carta 7-1. Pr evenzione degli inceppamenti della carta La carta non deve essere toccata durante l ’ espulsione e prima che sia tagliata.
– 87 – ITALIANO 8. Pulizia periodica I caratteri stampati possono diventare parzialmente poco chiari a causa dell ’ ac- cumulo di polvere di carta e sporcizia.
– 88 – APPENDIX A-1. General Specifications (1) Printing method Direct line thermal printing (2) Print speed Max. 1440 dots/sec. (180 mm/sec.) (3) Dot density 203 dpi: 8 dots/mm (0.125 mm/dot) (4) Printing width Max. 80 mm (5) Number of print columns 53 (12 × 24 dots) (6) Roll paper Refer to chapter 2 for details on the recommended roll paper.
– 89 – APPENDIX A-2. Auto Cutter Specifications (1) Cutting frequency Max. 20 cuts per minute (2) Thickness of paper 0.065 ~ 0.15 mm A-3. Interface RS-232C serial interface/Two-way parallel interface (IEEE1284)/USB inter- face/Ethernet interface/Wireless LAN Interface A-4.
– 90 – APPENDIX A-6. Environmental Requir ements (1) Operating Temperature 5 ° C to 45 ° C Humidity 10% to 90% RH (without condensation) (2) Transport/storage (except for paper) Temperature -20 ° C to 60 ° C Humidity 10% to 90% RH (without condensation) A-7.
– 91 – APPENDIX A-8. Black mark specifications <Remarks> 1.) The cut position shown above is when the print starting position correct value for Appendix F: memory switch 9 is the default setting. 2.) The black mark ’ s PCS value must be 0.
– 92 – APPENDIX Appendix B: Dip Switch Setting Two DIP switches are provided at the bottom of the printer, and can be set as given in the table below. Be sure to set the power switch to off before changing the settings. It is recommended to use a pointed item like a pen or flat-blade driver screw to change the settings.
– 93 – APPENDIX No. 1 DIP-SW1 2345678 No. 1 DIP-SW2 2 3 4 B-1. Parallel Interface Model ON ON OFF OFF DIP-SW 1 Switch 1-1 Command emulation ON Star Mode OFF ESC/POS Mode The factory settings of DIP switch are all on. The functions of switches 1-2 through 1-8 will change according to the command emulation that has been set using switch 1-1.
– 94 – APPENDIX DIP-SW 2 Switch Function ON OFF 2-1 2-2 Always ON Should be set to on 2-3 2-4 The factory settings of DIP switch are all on..
– 95 – APPENDIX No. 1 DIP-SW1 2345678 No. 1 DIP-SW2 2 3 4 B-2. Serial Interface Model ON ON OFF OFF DIP-SW 1 Switch 1-1 Command emulation ON Star Mode OFF ESC/POS Mode The factory settings of DIP switch are all on. The functions of switches 1-2 through 1-8 will change according to the command emulation that has been set using switche 1-1.
– 96 – APPENDIX DIP-SW 2 Switch Function ON OFF 2-1 2-2 Always ON Should be set to on 2-3 2-4 The factory settings of DIP switch are all on..
– 97 – APPENDIX The factory settings of DIP switch are all on, except for switches 7 and 8. DIP-SW 3 Switch Function ON OFF 3-1 Baud Rate See table below 3-2 3-3 Data Length 8 bits 7 bits 3-4 Pari.
– 98 – APPENDIX No. 1 DIP-SW1 2345678 No. 1 DIP-SW2 2 3 4 B-3. USB Interface Model ON ON OFF OFF Switch Function ON OFF 1-1 Command emulation (Ster Line mode) Always ON 1-2 Should not be changed (.
– 99 – APPENDIX No. 1 DIP-SW1 2345678 No. 1 DIP-SW2 2 3 4 B-4. Ethernet Interface Model ON ON OFF OFF Switch Function ON OFF 1-1 Command emulation (Ster Line mode) Always ON 1-2 Should not be chan.
– 100 – APPENDIX ■ DIP Switch (for E type) Switch Function ON OFF 3-1 Always OFF Should be set to off 3-2 Initialization of settings Valid Invalid 3-3 Always OFF Should be set to off 3-4 #9100 Multi-session Valid Invalid (Maximum 8 sessions) Change DIP Switch 3-2 to ON to initialize the setting information when the power is turned on.
– 101 – APPENDIX B-5. Wir eless LAN Interface Model DIP Switch ON OFF 3-1 Fixed at OFF 3-2 Initialize of setting information — The factory settings of DIP switch are all off. LED Display Green : Lights when pockets are received. DIP Switch 3 LED No.
– 102 – APPENDIX Installing the Ferrite Core (Wireless LAN Model for EU Only) Install the ferrite core onto the peripheral drive cable to prevent radio interfer- ence.
– 103 – APPENDIX Connecting the peripheral drive cable Connect the peripheral drive cable to the connector on the printer. Then, connect the other end of the cable to the peripheral drive circuit. For EU Except for EU 1 Install the ferrite core onto the peripheral drive cable as shown in the illustration.
– 104 – APPENDIX Parallel interface connector (printer side) This connector mates with an Amphenol 57-30360 connector Appendix C: Parallel Interface The two-way parallel interface is compatible with the IEEE1284 compatibility mode, nibble mode and byte mode.
– 105 – APPENDIX Appendix D: Serial Interface D-1. RS-232C Connector Pin No. Signal name Direction Function 25 Pin 9 Pin 1 F-GND — Frame ground 2 3 TXD OUT Transmission data 3 2 RXD IN Receive data 4 7 RTS OUT Same as DTR signal. 5 N/C Not used 8 CTS IN Status of this signal is not checked.
– 106 – APPENDIX Pin No. Signal name Direction Function 25 Pin 9 Pin 2) X-On/X-Off Communication Mode Always space, except during following conditions: • Period between reset and communication enabled • During self printing 21~24 N/C Not used 25 INIT IN Status of this signal is not checked.
– 107 – APPENDIX 1 2 3 4 5 6 1 2 3 4 5 6 7 8 20 FG FG TXD RXD RTS CTS DSR 20 25 7 SG DTR INIT Printer side (D-sub 25 pin) Host side 3 2 7 8 6 5 1 4 TXD RXD RTS CTS DSR SG DCD DTR 9 pin 25 pin 1 1 .
– 108 – APPENDIX Appendix E: USB, Ethernet and W ireless LAN Interface E-1. USB Interface Specifications 1. General Specification: Conforms to USB 2.0 Specifications 2. Communication Speed: USB Full Speed Mode (12 Mbps) 3. Communication Method: USB Bulk Transmission Mode 4.
– 109 – APPENDIX Note 1. Pin 1 must be shield drain wire connected to peripheral device frame ground. 2. It is not possible to drive two drives simultaneously. 3. The peripheral drive duty must satisfy the following: ON time / (ON time + OFF time) ≤ 0.
– 110 – APPENDIX Appendix G: Memory Switch Settings Each memory switch is stored in EEPROM. For details on the functions and settings of memory switches, see the separate Programmer ’ s Manual. The table below shows the factory settings for the memory switches.
.
WEEE Statement In the European Union, this label indicates that this product should not be disposed of with household waste . It should be deposited at an appropriate facility to enab le recovery and recycling in accordance with legislation under the WEEE Directive (Directiv e 2002/96/EC).
2006.06.30 Printed in China, 80870306 ELECTRONIC PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsusinya, Shimizu-ku, Shizuoka, 424 -0066 Japan Tel: 0543-47-0112, Fax: 0543-48-5013 Please access the following URL http://www.star- m.jp/eng/dl/dl02 .
Een belangrijk punt na aankoop van elk apparaat Star Micronics TSP700 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Star Micronics TSP700 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Star Micronics TSP700 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Star Micronics TSP700 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Star Micronics TSP700 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Star Micronics TSP700 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Star Micronics TSP700 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Star Micronics TSP700 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
