Gebruiksaanwijzing /service van het product MDCG-5121 van de fabrikant Barco
Ga naar pagina of 50
Servic e Manual This technical manual c ould incl ude technical inaccuracies or typographical errors . BARCO n.v . reserves the right to modify the manual as often as neces sary to keep it as current and ac cur ate as possible . This manual is c opyright ed by BARC O n.
2 MDCG-5121.
Ta b l e o f c o n t e n t s 3 1. T able of c ont ents Table of contents ................................................................ 3 Precautions ......................................................................... 4 Serviceable parts .....
4 Precautions 2. Pr ecautions G ENERAL • Disconnect fr om power befor e servicing the display . • Service is allow ed only by qualified service technicians in an acknowledged Barc o service center . • T ake the nec es sary measur es to pre vent electros tatic discharges (e .
Serviceable parts 5 3. Servic e able parts N° Description Par t N um b er Picture (1) L CD pane l (fr ont side) V323004 (2) Front be zel V622741 (1) (2).
6 Servicea ble parts N° Description Par t N um b er Picture (3) Rear c onnector housing cov er (connector cov er ) V622521 (4) Rear c ov er V6225201 (5) Neck cover (single foot) V622526 (3) (5) (4) (.
Serviceable parts 7 (6) Middle cov er V622742 (7) Foot (single) K9302030A N° Description Par t N um b er Picture.
8 Servicea ble parts N° Description Par t N um b er Picture (8) Arm cov er (2x) V622527 (9) Cable cov er V6226912 (10) Foot (dual) K9302042A ( 8) ( 10) ( 9) (8).
Serviceable parts 9 N° Description PartNumber Picture (11) Pow er board K5801525 (12) 900 Me zzanine board K5801520 (13) Cooling plat e me zzanine K600456 (11) (12) (14) (15) (13).
10 Servic eable pa rts (14) 900 Board K5801496 (15) F ans (2x) B3245671 N° Description PartNumber Picture.
Serviceable parts 11 N° Description PartNumber Picture (16) Mini BL OF board K58013511 (17) T emp sensor board K5801429 (16) (17).
12 Servic eable pa rts N° Description PartNumber Picture (1 8) Pane l (rea r side) V323004 (19) I-Guard K5801506 (18) (19).
Serviceable parts 13 N° Description PartNumber Picture (20) T ouch c ontrol board K5801536 Description Part Number Picture External Power supply B563069 UK power c ord B195613 EU power c ord Z348791 .
14 Servic eable pa rts US power c ord Z348790 PRC power c ord Z3487500 DisplayPort cable B558295 USB cable B558310 Firmwar e K5402560 NA Box display K6100125 Buffers K6100120 Description Part Number P.
Service instructions 15 4. Servic e instructions 4.1 Back co v ers S ERVIC EABLE PARTS This proc edure describes and c ov ers the replac ement of following service able parts: • Connect or co ver .
16 Servic e instructions R EMO VE THE BACK COVER 1 Unscre w the 4 scre ws in the mounting anchor 2 Slightly push at the bo ttom of the c over , position 5th blade from both side s of the grid, to rele ase the 2 clips from the middle cov e r . 3 Slightly lift the bott om side of the back c over .
Service instructions 17 R EMO VE THE PCB BRACK ET 1 Unscre w the 21 screws of the PCB br acket . 2 Unscre w the 2 scre ws of the side USB connect ors .
18 Servic e instructions 3 Slightly lift the co ver at the bottom side and pull tow ards the bottom to rele ase the co ver (at the t op) from the L CD bracket.
Service instructions 19 4.2 900 Me zzanine S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • 900 mezzanine P RE REQ U IS I TE S Following .
20 Servic e instructions 4 Unscre w the 2 scre ws and the 4 spacers of the me zzanine. 5 Care fully lift the mezzanine , to r elease the boar d from the connector s.
Service instructions 21 4.3 900 & pow er board S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • 900 board • Power b oard P RE REQ U.
22 Servic e instructions R EMO VE THE 900 & POW ER BOAR D 1 Disconnect the 7 cable s of the 900 and power boar d . 2 Unscre w the 13 screws and 6 spac ers of the 900 board and the po wer board. 3 Unscre w the 4 screws and 2 spac ers of the USB, DVI, DisplyPort an d power conn ectors .
Service instructions 23 R EASS EM B LI N G Reas sembling the display can be done by f o llowing the previously described pr ocedur e in rev erse order but also check the official display’s workinstruction ( WI9301500A ) to ens ure th at n othi ng is forg otten .
24 Servic e instructions 4.4 Be ze l S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • Front bezel P RE REQ U IS I TE S Following tools wi.
Service instructions 25 2 Disc onnect the touch panel cable. 3 Tur n t h e di s p la y so t h at t he s c re e n is fa ci n g u p , m a k e s u re t o h o l d b o th t h e pa n e l and bez el and place it with the back on the surfac e. 4 Carefully lift the be zel from the displa y .
26 Servic e instructions 4.5 T ouch con tr ol board S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • T ouch control boar d P RE REQ U IS I TE S Following tools will be requir ed for this procedur e: • Thin metal bar (max 0.
Service instructions 27 4.6 I- Guar d S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • I-Gua rd P RE REQ U IS I TE S Following tools will.
28 Servic e instructions 5 The dust cap around the I-Guard sensor is not fixed to the sensor . Do not loose it when removing the I-Guard board. R EASS EM B LI N G Reas sembling the display can be done.
Service instructions 29 4.7 L CD br acke t S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • LCD b r a c k et P RE REQ U IS I TE S Followi.
30 Servic e instructions 5 Lift the L CD bracket at the opposite side of the side USB c onnectors, be carefull for the c onnections towards the panel. 6 Disc onnect the 6 cables between L CD bracket and panel and unscre w the 2 cab le clamp scre ws so that L CD bracket is free to be re moved.
Service instructions 31 4.8 T emper atur e sensor board S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • Te m p e r a t u r e s e n s o r.
32 Servic e instructions 4.9 Mini BL OF S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • Mini BL OF P RE REQ U IS I TE S Following tools .
Service instructions 33 4 Remove the BL OF board. R EASS EM B LI N G Reas sembling the display can be done by f o llowing the previously described pr ocedur e in rev erse order but also check the official display’s workinstruction ( WI9301500A ) to ens ure th at n othi ng is forg otten .
34 Servic e instructions 4.10 F ans S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • Fa n s P RE REQ U IS I TE S Following tools will be .
Service instructions 35 4.11 L CD P anel S ERVIC EABLE PARTS This proc edure describes and c overs the replac ement of following service able parts: • Pan el P RE REQ U IS I TE S Following tools wil.
36 I-Guard calibration 5. I- Guard calibr ation I NTRODUCTION The calibr ation must be performed using the Minolta CA - 210 measurement instru ment , the calibration c over and MFDContr ol (IMPORT ANT - internal use only).
I-Guard calibration 37 5 Press the CAL butt on sever al times until the M-SPD menu appe ars. 6 Press the Blue (>) butt on sever al times until the M-SPD is set to SL OW .
38 I-Guard calibration 3 After 0 - calibration, turn the pointing ring to the “ME AS” position. R EMARK S : If the ambient temper ature changes , redo t he ze ro calibr ation The zero calibr ation.
I-Guard calibration 39 5 Make sure the check bo x UL T enable is not checked. E xit the UL T menu. 6 In the main menu, click I- Guard to enter the I-Guard menu.
40 I-Guard calibration 8 In the next menu, the pr ogram will detect the BL OS and I-Guard. Click the Auto button in the I-Guard, BLOS section of the screen.
I-Guard calibration 41 2 When the calibr ation is finished,set the char acteriz e panel radio button to Use patch and click Do it to start panel char acterization. 3 When done , exit t he I-Guard screens a nd return to the main s creen. I-G UARD CALIBRA TION (UL T ON ) 1 In the main menu, click the UL T button.
42 I-Guard calibration 3 In the main menu, click I- Guard to enter the I-Guard menu. 4 Click Monochrome I-Guard . 5 Click Calibr ate t o start the I-Guard calibration with UL T on.
I-Guard calibration 43 6 When the I-Guard calibra tion is finished, set the char acteriz e panel rad io bu tto n to Use patch and click Do it to start panel characterization. S TABALIZ ER MODELING 1 When the panel char acterization is finished, click Stabi lizer Modeling .
44 I-Guard calibration I-G UARD PATCH AUTO POSITION 1 Click I-Guard in the main menu. 2 Click Pat c h Co nt ro l . 3 Click Auto P osition . 4 When don e, e xit MFDCon trol.
Firmw are upload 45 6. Firmw ar e upload P RE REQ U IS I TE S • USB stick • Pas skey for OSD servic e mode (production user:) • Acc ess to the FW rele ase folders T O UPLOAD THE FIRMWAR E 1 Cop y the applicable FW version (official versions av ailable in B aaN) to your USB stick’s root f older .
46 Firmw are upload 5 Enter the Servic e > Upload Firmw are menu. The display will now search for all available FW folders present on th e connect ed USB stick .
Reading/writing E EPROM data 47 7. R e ading/writing EEPROM da ta P RE REQ U IS I TE S • Latest version of MFDC ontrol R EAD IN G EEPROM DATA 1 Start MFDCont rol 2 In the main menu, select the appropriate display . 3 Click Upload. 4 In the Upload window , click EEPROM to fi le .
48 Reading/writing EEPR OM data W RITI NG EEPROM DATA 1 Sta rt MFDCont rol . 2 In the main menu, select the appropriate display . 3 Click Upload. 4 In the Upload window , click File to EEPROM . 5 Locate the appropriat e file and click Open . The data is written into the display EEPROM.
UL T upload 49 8. UL T upload M ANUAL PROC EDURE Uploading UL T data for the MDC G-5121 is curr ently not possible with MFDContr ol (as it was done bef ore with other displays). Pending an update of MFDC ontrol, UL T upload is only possible through a manual proc edure.
Bar co n. v . President Kennedypark 35 8500 Kortrijk Belgium www .barco .com B4100600-00 November 2011.
Een belangrijk punt na aankoop van elk apparaat Barco MDCG-5121 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Barco MDCG-5121 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Barco MDCG-5121 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Barco MDCG-5121 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Barco MDCG-5121 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Barco MDCG-5121 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Barco MDCG-5121 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Barco MDCG-5121 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
