Gebruiksaanwijzing /service van het product C 1600-12 van de fabrikant Studer
Ga naar pagina of 23
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E User and installer Manual Sine wave Inverter, Battery charger, Transfersystem COMPACT C 1600-12 COMPACT C 2600-24 COMPACT C 4000-48 Temperature sensor.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 2 Summary 1 G ENERAL I NFORMATION ............................................................................................................... 4 1.1 O PERATING INSTRUCTIONS .........................
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 3 4.7.3 D ELAYED MODE OF THE T RANSFER S YSTEM .....................................................................................17 4.8 T HE S OLAR CHAR GE CONT ROLLER ( OPTION ) ...................
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 4 1 General Information 1.1 Operating instructions This manual is a part of the delivery package of every COMPACT inverter-charger.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 5 During operation of COMPACT, high tensions are generated at the connections and inside of t he appliance which could be deadly fatal. Work on the appliance and on t he installation should only be carried out by qualified and trained personnel.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 6 2 Introduction The COMPACT is a sine wave inverter with integrated battery charger and solar charger controller with many additional functions, it has been developed to be used as stand-alone (independent of a grid-system) AC provider, or as conti nuous / break-free current supply provider.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 7 2.2.4 The solar charge controller (optional) With the built-in solar charge controller, the COMPACT is a complete solar-power-center. In a solar installation this controller ensures that the batteries are ch arged correctly.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 8 2.3.3 Parallel- Series Connection 3 Assembly 3.1 Place of assembly The location of the COMPACT must be chosen by the following criteria: Protection from unauthorized handling. Dry dust free room, no condensation.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 9 3.3.2 Protection cover for the terminals connections The protection is available as an option (Order ref. CFC-01) and avoid to do wrong hazardous connection on the terminals 230Vac. It mounted with strain relief clamps for the cable.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 10 G Aux. Contact Connecting terminal for Auxiliary Contact H AC Input Connecting terminal for AC-input.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 11 3.5.4 Connection the 230Vac Input (AC INPUT) The 230V-supply from network or from a generator must be connected to the scre w terminals AC INPUT. For this use a 3-core cable with a conductor cro ss section of 2.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 12 OFF AC OUT AC IN Ove r Tem p Over loa d ON/OFF SOLAR CHARGE Batt L ow/Hig h Contact m anual AUX. CONTACT 70A 15 0V 20W OFF 0 Contact act ive Progr .
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 13 4.2 Light Emitting Diodes LED Marking LED lit LED blinks 1 AC IN Voltage corresponding to self- adjusted values is at the AC IN input. Voltage, outside of the self- adjusted values is at the AC IN input.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 14 4.5 The Inverter An Inverter is built in the COMPACT, which generates a sinusoidal alternating voltage of a very high quality. With this Inverter any alternating voltage consuming device 230Vac up to the nominal power of your COMPACT can be operated.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 15 1.9 2.3 2.50 [V/cell] 2.1 A B C D 20 60 40 70 [A] A B C D t Equaliz ation Absorption Floating Chargin g cur rent ( adjust ed) Chargin g ti me Egaliz ation t ime Absorption time Floati ng 4.6 The Battery charger 4.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 16 the OUTPUT less it’s give to the charger. Priority to the OUTPUT. When the power sharing is used the LED 200% (red) is lit to point out that’s the charge is limited.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 17 The Transfer system is protected against overload wi th an automatic safety fuse on the AC Input side of the COMPACT. If the system has been overloaded the button/pin of the fuse will pop-out. To put the automatic safety system back in to operating you must push this pin back.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 18 4.9 The Multifunctional Contact In the COMPACT there is a built-in programmable power relay. The potential-free change-over contact (NO – NC) of this power relay is c onnected to the screw terminal AUX CONTACT.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 19 Caution: No external voltage should be connected to this Input Control. 4.11 The Temperature sensor Operating voltage of lead-acid batteries change depends on the temperature.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 20 5.3.2 Set the voltage and timing threshold The programming is done in accordance with the following steps: Push and hold down, the Push Button 21 (Program) and the Push Button 19 (Change status) for minimum 2 seconds simultaneously.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 21 5.4.3 Examples 5.4.3.1 Auxiliary Contac t as generator starter As per the battery capacity When in the programming of the Auxiliary Contac t, the Battery Capacity (LED 15-18) is used as a condition, then you must take note of the following requirements.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 22 5.5.1 Diagram of the different modes 9 Show an off LED Show a blinking LED Show a lighted LED CHARGE R IN VER TE R AC OUT AC IN 1 2 7 8 9 All the functions are enabled. This is the factory setting. CHARGE R IN VER TE R AC OUT AC IN 1 2 7 8 9 The inverter is disabled.
STUDER INNOTEC COMPACT User manual COMPACT V4.0 E 23 8 Technical Data Technical data Model C 1600-12 C 2600-24 C 4000-48 Inverter Nominal battery voltage 12V 24V 48V Input voltage range 9.5 - 16V 19 - 32V 38 - 64V Continuous power @ 2 5°C 1300VA 2300VA 3500VA Power 30 min.
Een belangrijk punt na aankoop van elk apparaat Studer C 1600-12 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Studer C 1600-12 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Studer C 1600-12 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Studer C 1600-12 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Studer C 1600-12 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Studer C 1600-12 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Studer C 1600-12 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Studer C 1600-12 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
