Gebruiksaanwijzing /service van het product Sun Fire X2100 M2 van de fabrikant Sun Microsystems
Ga naar pagina of 40
Sun Microsystems, Inc. www .sun.com Submit comments about this document at: http://www.sun.com/hwdocs/feedback Sun Fire ™ X2100 M2 Ser v er Installation Guide P ar t No .
Please Recycle Copyright 2006 Sun Microsystems, Inc., 4150 Network Cir cle, Santa Clara, California 95054, U.S.A. All rights reserved. Sun Microsystems, Inc.
iii Contents 1. Setting Up the Sun Fire X2100 M2 Server Hardware 1 Safety and Compliance Information 1 Planning the Installation Process 2 Package Contents Inventory 3 Installing the Server Into a Rac.
iv Sun Fire X2100 M2 Server Installation Guide • August 2006 3. Conf iguring the Preinstalled Solaris 10 Operating System 27 Before You Begin 27 Installation W orksheet 27 Configuring the Preinstall.
1 CHAPTER 1 Setting Up the Sun Fir e X2100 M2 Server Har dware This chapter describes how to set up the Sun Fire X2100 M2 server hardwar e. It includes the following topics: ■ “Safety and Complian.
2 Sun Fire X2100 M2 Server Installation Guide • August 2006 Planning the Installation Pr ocess Use the flowchart in FIGURE 1- 1 to assist you with the server installation. FIGURE 1-1 Sun Fire X2100 M2 Server Installation Pr ocess Unpack the server and f amiliar ize y ourself with the ser v er features .
Chapter 1 Setting Up the Sun Fire X2100 M2 Ser v er Hardware 3 Package Contents Inventory Carefully unpack all server components fr om the packing cartons.
4 Sun Fire X2100 M2 Server Installation Guide • August 2006 Installing the Server Into a Rack W ith Optional Slide Rails The service label on the top cover of the Sun Fire X2100 M2 server contains instructions for installing your server into a four-post rack using the or derable slide- rail and cable management arm options.
Chapter 1 Setting Up the Sun Fire X2100 M2 Ser v er Hardware 5 Connecting the Cables See FIGURE 1-2 and T ABLE 1- 1 for the locations of the connectors. ▼ T o Connect the Cables Connect the server and external devices as follows: 1. Connect the server power cord to a grounded electrical outlet.
6 Sun Fire X2100 M2 Server Installation Guide • August 2006 FIGURE 1-2 Back Panel Powering On and Powering Of f the Server Y ou only need to apply standby power to the server at this point so that you can perform initial configuration of the service pr ocessor .
Chapter 1 Setting Up the Sun Fire X2100 M2 Ser v er Hardware 7 ▼ T o Apply Standby Power for Initial Service Pr ocessor Conf iguration Use this procedur e to apply standby power to the service processor (SP) before initial configuration.
8 Sun Fire X2100 M2 Server Installation Guide • August 2006 ▼ T o Power On Main Power Mode T o power on main power for all server components: a. V erify that the power cord has been connected and that standby power is on. In standby power mode, the Power/OK LED on the front panel f lashes.
Chapter 1 Setting Up the Sun Fire X2100 M2 Ser v er Hardware 9 Setup T r oubleshooting and Support This section contains information to help you troubleshoot minor server problems. It includes the following topics: ■ “T roubleshooting the Sun Fire X2100 M2 Server Setup” on page 9 .
10 Sun Fire X2100 M2 Server Installation Guide • August 2006 Note – For additional troubleshooting information, see Sun Fire X2100 M2 Server Service Manual, 819-6591.
Chapter 1 Setting Up the Sun Fire X2100 M2 Ser v er Hardware 11 Contacting Support If the troubleshooting pr ocedures in this chapter fail to solve your pr oblem, use T ABLE 1-4 to collect information that you might need to communicate to the support personnel.
12 Sun Fire X2100 M2 Server Installation Guide • August 2006 Sun Fir e X2100 M2 Server Documentation For a description of the document set for the Sun Fire X2100 M2 server , see the Where T o Find Documentation sheet that is packed with your system and also posted at the product's documentation site.
13 CHAPTER 2 Setting Up the Sun Fir e X2100 M2 Server Softwar e This chapter describes how to set up the Embedded Lights Out Manager (LOM) service processor (SP).
14 Sun Fire X2100 M2 Server Installation Guide • August 2006 ■ Embedded LOM f irmware. Preinstalled on the service pr ocessor chipset is a library of system management firmware applications. This service pr ocessor firmwar e is operating system independent.
Chapter 2 Setting Up the Sun Fire X2100 M2 Ser v er Software 15 Performing Initial Conf iguration of the Embedded LOM Service Pr ocessor This section describes two methods for connecting to your Embedded LOM SP to perform initial setup and configuration.
16 Sun Fire X2100 M2 Server Installation Guide • August 2006 Note – If you connect to the serial port on the Embedded LOM before it has been powered on or during its power -on sequence, boot up messages display . The Embedded LOM eventually displays a login prompt.
Chapter 2 Setting Up the Sun Fire X2100 M2 Ser v er Software 17 Note – Y ou can switch back to the Embedded LOM command-line interface (CLI) from the serial console by entering the following key sequence: Esc + Shift + 9.
18 Sun Fire X2100 M2 Server Installation Guide • August 2006 Note – This procedur e assumes that you have already completed the har dware setup and have applied standby power for your server , as described in Chapter 1 of this guide. 1. V erify that your DHCP server is conf igured to accept new media access control (MAC) addresses.
Chapter 2 Setting Up the Sun Fire X2100 M2 Ser v er Software 19 b. Identify the IP address in the log f ile that corresponds to the MAC address of your SP .
20 Sun Fire X2100 M2 Server Installation Guide • August 2006 FIGURE 2-2 Embedded LOM Login Screen 7. T ype Embedded LOM SP commands in the CLI or navigate to Embedded LOM web GUI pages to conf igure your Embedded LOM SP .
Chapter 2 Setting Up the Sun Fire X2100 M2 Ser v er Software 21 2. Connect to the SP through a web browser running on a remote system. 3. Log in to the web GUI using the default user name, root , and the default password, changeme . The initial Embedded LOM screen displays.
22 Sun Fire X2100 M2 Server Installation Guide • August 2006 FIGURE 2-4 Embedded LOM Control Menu 5. Select Network from the drop-down menu to display information about the current network conf iguration of your Embedded LOM SP . The Network Settings Page displays.
Chapter 2 Setting Up the Sun Fire X2100 M2 Ser v er Software 23 ▼ T o Conf igur e Static IP Addresses Using the CLI 1. Log into the CLI using SSH or by connecting to the serial port. T o establish a SSH connection to the Embedded LOM SP CLI, type the appropriate connection command in the SSH application.
24 Sun Fire X2100 M2 Server Installation Guide • August 2006 2. Launch the console from the SP using the following command: start /SP/AgentInfo/console Make sure to watch the output carefully , so that you don’t miss the intial BIOS screens.
Chapter 2 Setting Up the Sun Fire X2100 M2 Ser v er Software 25 Conf iguring or Installing System Softwar e If your server has at least one hard drive installed, the server might have the Solaris ™ 10 Operating System and additional software preinstalled.
26 Sun Fire X2100 M2 Server Installation Guide • August 2006 Additional Pr einstalled Softwar e Additional software will be pr einstalled on the Sun Fire X2100 M2 server , including Sun Java™ Enterprise System (JES) and Sun ™ Studio. See the following table for where to f ind information and downloads for these software products.
27 CHAPTER 3 Conf iguring the Preinstalled Solaris 10 Operating System This chapter walks you through the steps for conf iguring the Solaris 10 Operating System (OS) that might be preinstalled on your Sun Fir e X2100 M2 server , depending on your hard drive conf iguration.
28 Sun Fire X2100 M2 Server Installation Guide • August 2006 T ABLE 1 Installation W orksheet Information f or Installation Description or Example Y our Answers: Defaults are noted with an asterisk. (*) Language Choose from the list of available languages for the Solaris 10 software.
Chapter 3 Configuring the Preinstalled Solar is 10 Operating System 29 Host name A host name that you choose for the system. Kerberos Do you want to configur e Kerberos security on this machine? If ye.
30 Sun Fire X2100 M2 Server Installation Guide • August 2006 Default route Do you want to specify a default route IP addr ess or let the Solaris installation program find one? The default route pr ovides a bridge that forwards traff ic between two physical networks.
Chapter 3 Configuring the Preinstalled Solar is 10 Operating System 31 Conf iguring the Preinstalled Solaris 10 Operating System Note – Before you perform this pr ocedure, you need to set up the service pr ocessor if you have not done so. See Chapter 2 .
32 Sun Fire X2100 M2 Server Installation Guide • August 2006 ▼ T o Connect to the Server Using the Service Pr ocessor ’s IP Addr ess Note – This procedur e assumes that you have connected the server to your network through an Ethernet cable. 1.
Chapter 3 Configuring the Preinstalled Solar is 10 Operating System 33 5. If you have changed the SP Serial Port default settings, make sure you reset them to the default settings.
34 Sun Fire X2100 M2 Server Installation Guide • August 2006 2. Make sure that the communication properties of the serial port of the system are set to the default. The defaults are 9600 baud, 8N1 (eight data bits, no parity , one stop bit), and disable flow contr ol.
Chapter 3 Configuring the Preinstalled Solar is 10 Operating System 35 Solaris 10 Operating System User Information This section provides pointers to information on the Solaris 10 operating system. Accessing Solaris 10 User Documentation Y ou can access the various collections of the Solaris 10 OS user documentation at: http://docs.
36 Sun Fire X2100 M2 Server Installation Guide • August 2006.
Een belangrijk punt na aankoop van elk apparaat Sun Microsystems Sun Fire X2100 M2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sun Microsystems Sun Fire X2100 M2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sun Microsystems Sun Fire X2100 M2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sun Microsystems Sun Fire X2100 M2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sun Microsystems Sun Fire X2100 M2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sun Microsystems Sun Fire X2100 M2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sun Microsystems Sun Fire X2100 M2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sun Microsystems Sun Fire X2100 M2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
