Gebruiksaanwijzing /service van het product T6300 van de fabrikant Sun Microsystems
Ga naar pagina of 52
Sun Microsystems, Inc. www .sun.com Submit comments about this document at: http://www.sun.com/hwdocs/feedback Sun Blade™ T6300 Ser v er Module Administration Guide P ar t No .
Please Recycle Copyright 2007 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Sun Microsystems, Inc.
iii Contents Preface xi 1. Conf iguring the System Console 1 Communicating With the Server 1 What the System Console Does 2 What the ALOM System Controller Console Does 2 Using the System Console 2 De.
iv Sun Blade T6300 Server Module Administration Guide • April 2007 ▼ T o Access the System Console Through an Alphanumeric T erminal 8 Switching Between the ALOM System Controller and the System C.
Contents v Automatic System Recovery User Commands 24 Enabling and Disabling Automatic System Recovery 25 ▼ T o Enable Automatic System Recovery 25 ▼ T o Disable Automatic System Recovery 26 Obtai.
vi Sun Blade T6300 Server Module Administration Guide • April 2007.
vii Figur es FIGURE 1-1 Switching Between ALOM System Controller and System Console 9.
viii Sun Blade T6300 Server Module Administration Guide • April 2007.
ix T ables T ABLE 1-1 Pin Crossovers for Connecting the Server to a Terminal Server 5 T ABLE 1-2 Ways of Accessing the ok Prompt 16 T ABLE 1-3 OpenBoot Configuration Variables That Affect the System C.
x Sun Blade T6300 Server Module Administration Guide • April 2007.
xi Pr eface The Sun Blade T6300 Server Module Administration Guide is written for experienced system administrators. This guide includes general descriptive information about the Sun Blade™ T6300 server module and detailed instructions for conf iguring and administering the server module.
xii Sun Blade T6300 Server Module Administration Guide • April 2007 Using UNIX Commands This document might not contain information on basic UNIX ® commands and procedur es such as shutting down the system, booting the system, and configuring devices.
Preface xiii T ypographic Conventions Related Documentation The documents listed as online are available at: http://www.sun.com/documentation/ T ypeface * * The settings on your browser might differ from these settings. Meaning Examples AaBbCc123 The names of commands, files, and directories; on-scr een computer output Edit your .
xiv Sun Blade T6300 Server Module Administration Guide • April 2007 Documentation, Support, and T raining Thir d-Party W eb Sites Sun is not responsible for the availability of third-party web sites mentioned in this document.
1 CHAPTER 1 Conf iguring the System Console This chapter explains what the system console is, describes the different ways of configuring it on your server , and helps you understand its relation to the system controller .
2 Sun Blade T6300 Server Module Administration Guide • April 2007 What the System Console Does The system console displays status and error messages generated by firmwar e-based tests during system startup. After running those tests, you can enter special commands that affect the f irmware and alter system behavior .
Chapter 1 Configuring the System Console 3 These constraints provide for secure access at the installation site. Using a TIP line enables you to use windowing and operating system features on the system making the connection to your server .
4 Sun Blade T6300 Server Module Administration Guide • April 2007 ▼ T o Use the Serial Port 1. Ensure that the serial port on your connecting device is set to the following parameters: ■ 9600 baud ■ 8 bits ■ No parity ■ 1 stop bit ■ No handshaking 2.
Chapter 1 Configuring the System Console 5 ▼ T o Access The System Console Through a T erminal Server 1. Complete the physical connection from the serial port to your terminal server . The serial port on the server is a data terminal equipment (DTE) port.
6 Sun Blade T6300 Server Module Administration Guide • April 2007 For example, for a server connected to port 10000 on a terminal server whose IP address is 192.
Chapter 1 Configuring the System Console 7 Modifying the /etc/remote File This procedur e might be necessary if you are accessing the server module using a TIP connection from a Sun system r unning an older version of the Solaris OS software.
8 Sun Blade T6300 Server Module Administration Guide • April 2007 Note – If you intend to use the Sun system’s serial port A rather than serial port B, edit this entry by replacing /dev/ttyb with /dev/ttya .
Chapter 1 Configuring the System Console 9 Switching Between the ALOM System Contr oller and the System Console If the system console is directed to the virtual-console device (its default configuration), the serial port and the network management port provide access to both the system console and the ALOM system controller (see FIGURE 1- 1 ).
10 Sun Blade T6300 Server Module Administration Guide • April 2007 The prompt displayed on the terminal or shell tool indicates which channel you are accessing: ■ The # or % prompt indicates that you ar e at the system console and that the Solaris OS is running.
Chapter 1 Configuring the System Console 11 Note – When you access the ALOM system controller for the first time and you issue an administrative command, you must create a password for the default username, admin, for subsequent access.
12 Sun Blade T6300 Server Module Administration Guide • April 2007 Reaching the sc> Pr ompt There ar e several ways to obtain the sc> prompt: ■ Y ou can log in directly to the ALOM system controller fr om a device connected to the serial port.
Chapter 1 Configuring the System Console 13 ■ When a serious hardwar e problem develops while the system is running, the operating system transitions smoothly to run level 0. ■ When you deliberately place the system under firmwar e control in or der to execute firmwar e-based commands.
14 Sun Blade T6300 Server Module Administration Guide • April 2007 Gracefully shutting down the system prevents data loss, enables you to warn users beforehand, and causes minimal disruption. Y ou can usually perform a graceful shutdown, provided the Solaris OS is running and the har dware has not experienced serious failure.
Chapter 1 Configuring the System Console 15 Using these commands results in the loss of all system coherence and state information. A manual system reset could corrupt the server ’s f ile systems, although the fsck command usually restor es them. Use this method only when nothing else works.
16 Sun Blade T6300 Server Module Administration Guide • April 2007 Caution – Forcing the server to the ok pr ompt suspends all application and operating system software. After you issue f irmware commands and run f irmware- based tests from the ok pr ompt, the system might not be able to resume where it left off.
Chapter 1 Configuring the System Console 17 System Console OpenBoot Conf iguration V ariable Settings Certain OpenBoot configuration variables contr ol from wher e system console input is taken and to where its output is dir ected. The table below shows how to set these variables in order to use the serial port and network management port.
18 Sun Blade T6300 Server Module Administration Guide • April 2007.
19 CHAPTER 2 Managing RAS Featur es and System Firmwar e This chapter describes how to manage reliability , availability , and serviceability (RAS) features and system f irmware, including the Sun Advanced Lights Out Manager (ALOM) system controller, and Automatic System Recovery (ASR).
20 Sun Blade T6300 Server Module Administration Guide • April 2007 Interpr eting System LEDs The behavior of LEDs on your server conforms to the American National Standar ds Institute (ANSI) Status Indicator Standard (SIS). These standard LED behaviors ar e described in T ABLE 2-1 .
Chapter 2 Managing RAS Features and System Firmware 21 Contr olling the Locator LED Y ou control the Locator LED from the sc> pr ompt or by the Locator button on the front of the server module.
22 Sun Blade T6300 Server Module Administration Guide • April 2007 ▼ T o Display the State of the Locator LED Fr om the ALOM System Controller Command Pr ompt ● T ype: Note – Y ou do not need user permissions to use the setlocator and showlocator commands.
Chapter 2 Managing RAS Features and System Firmware 23 ▼ T o Enable an Automatic Degraded Boot ● Set the switches by typing: Note – The default setting for auto-boot-on-error? is false . The system will not attempt a degraded boot unless you change this setting to true .
24 Sun Blade T6300 Server Module Administration Guide • April 2007 ■ If a fatal error is detected by POST or OpenBoot Diagnostics, the system does not boot regar dless of the settings of auto-boot? or auto-boot-on-error? .
Chapter 2 Managing RAS Features and System Firmware 25 ■ “Unconfiguring and Reconf iguring Devices” on page 27 ■ “T o Reconfigur e a Device Manually” on page 27 ■ “Obtaining Automatic System Recovery Information” on page 26 Enabling and Disabling Automatic System Recovery The ASR feature is not activated until you enable it.
26 Sun Blade T6300 Server Module Administration Guide • April 2007 ▼ T o Disable Automatic System Recovery 1. At the ok prompt, type: 2. T o cause the parameter changes to take effect, type: The system permanently stores the parameter change.
Chapter 2 Managing RAS Features and System Firmware 27 Unconf iguring and Reconfiguring Devices T o support a degraded boot capability , the ALOM firmware pr ovides the disablecomponent command, which enables you to unconfigure system devices manually .
28 Sun Blade T6300 Server Module Administration Guide • April 2007 Note – The device identifiers ar e not case-sensitive. Y ou can type them as uppercase or lowercase characters. Y ou can use the ALOM enablecomponent command to reconf igure any device that you previously unconf igured with the disablecomponent command.
Chapter 2 Managing RAS Features and System Firmware 29 Adding the –v option displays additional information, For more information about the showfaults command, r efer to the Advanced Lights Out Management (ALOM) CMT v1.
30 Sun Blade T6300 Server Module Administration Guide • April 2007 For information about VVM and its DMP feature, refer to the documentation provided with the VERIT AS V olume Manager software. For information about Sun StorageT ek T raff ic Manager , refer to your Solaris OS documentation.
31 APPENDIX A OpenBoot Conf iguration V ariables T ABLE A-1 describes the OpenBoot firmwar e configuration variables stored in non- volatile memory on the system. The OpenBoot configuration variables ar e printed here in the or der in which they appear when you issue the showenv command.
32 Sun Blade T6300 Server Module Administration Guide • April 2007 ttya-mode 9600,8,n,1,- 9600,8,n,1,- Serial management port (baud rate, bits, parity , stop, handshake). The serial management port only works at the default values. output-device virtual- console, ttya virtual- console Power-on output device.
Appendix A OpenBoot Configuration V ariables 33 diag-switch? true, false false If true : • OpenBoot verbosity is set to maximum. • After a boot r equest, boot diag-file from diag-device . If false : • OpenBoot verbosity is set to minimum. • After a boot r equest, boot boot-file from boot-device .
34 Sun Blade T6300 Server Module Administration Guide • April 2007.
35 Index Symbols /etc/remote file, 6 modifying, 7 A Advanced Lights Out Manager (ALOM) escape sequence (#.), 12 multiple connections to, 1 1 ALOM commands disablecomponent ,2 7 enablecomponent ,2 7 a.
36 Sun Blade T6300 Server Module Administration Guide • Apr il 2007 input-device (OpenBoot configuration variable), 17 K keyboard sequences L1-A, 13, 1 4, 16 L L1-A keyboard sequence, 13, 14, 1 6 L.
Index 37 as default communication port on initial startup, 1 configuration parameters, 4 using, 3 SERIAL MGT , See serial management port setlocator ( sc> command), 21 showenv (OpenBoot command), .
38 Sun Blade T6300 Server Module Administration Guide • Apr il 2007.
Een belangrijk punt na aankoop van elk apparaat Sun Microsystems T6300 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sun Microsystems T6300 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sun Microsystems T6300 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sun Microsystems T6300 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sun Microsystems T6300 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sun Microsystems T6300 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sun Microsystems T6300 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sun Microsystems T6300 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
