Gebruiksaanwijzing /service van het product R9050100 van de fabrikant Barco
Ga naar pagina of 229
CLM R1 0+ Users manual R9050100 R90501001 R90501005 R59770021/11 11/10/2010.
Barco nv E vents Noordlaan 5, B-8 520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.88.24 E-mail: sales.events@barco.com Visit us at the web: www.barco.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
This software and the accompanying fi les are sold “as is” and without warranties as to perfor mance or merchantability or any other war- ranties whether expressed or implied.
Tabl e of cont ents T ABLE OF C ONTEN TS 1 . S a f e t y...... .......... ........ ...... ........ ...... ........ ...... .......... ........ ...... ........ ...... .......... ....... 5 1.1 General ..................... .............................. .
Tabl e of cont ents 8 . I n p u t m e n u ... ...... ........ ...... .......... ........ ...... ........ ...... .......... ........ ...... ........ ...... ......6 3 8.1 Ove rvie w fl o w....... ....................... .............................. .
Tabl e of cont ents 1 2 . 4 S i d e k e y s t o n e .............................. ..................................... .............................. .............. ........ 1 2 0 1 2 . 5 B l a n k i n g ..................... ...................... .
Tabl e of cont ents 16.7 Removal of an input module ............................. .............................. ...................... ...................... 1 7 6 16.8 Inserting an input module . . ...................... ............................
1. Safety 1. SAFETY About this chapter Read this chapter attentively . It contains important informatio n to prevent pe rsonal injury w hile installing and using an C LM R10+ projector . Furthermore, it includes several cautions to prevent damage to the CLM R 10+.
1. Safety 1.2 Important safety instructions T o pre vent the ri sk of elect rical shock • Wa rn in g : T his apparatus must be grounde d (earthed) via the supplied 3 conductor A C power cable. If none of the supplied power cables are the correct one, consult your dealer .
1. Safety • Mercur y V apor W arnings : Kee p the following warnings in m ind when using the projector . The lamp used in the p rojector contains mercury .
1. Safety • In the ev ent of fi re, use sand, CO 2 , or dry powder fi re extinguishers; never use water on an electrical fi re. • This product should never be placed near or ov er a radiator or heat register . • This projector should not be placed in a built-in installat ion or enclosure unless proper ventilation is provided.
1. Safety 1.4 Important warnings concerning CLM fl ight cases Important warnings conce rning stacking/transporting CLM rental fl ight cases • S tac k maxi mum t wo (2) C LM rent al fl ight cases high.
1. Safety 10 R59770021 CLM R10+ 11/10/2010.
2. Gener al 2. GENERAL About this chapter Read this chapter before ins talling your CLM R10+. It contains important information concerning inst allation requirements for the CLM R10+, such as minimum .
2. Gener al Which s creen type ? There are two major categories of screens used for proj ection equipment. Those used for front projected images and t hose for rear projection applications.
2. Gener al Image 2-2 Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector . For maximum protection, repack your projector as it was originally packed at the factory . A rubber foam inside a plastic bag is placed into the lens opening of the projector .
2. Gener al 2.4 Projector con fi gurations The different con fi gura tions Depending on the installation the projector can be mounted in different ways, the 4 dif ferent con fi gurations are: 1. Front / T able (F/T) 2. Front / Ceiling (F/C) 3. Rear / T able (R/T) 4.
2. Gener al Positionin g the projector FLOOR SCR EEN SCR EEN PD A CD SCREEN SW SW SH B SH B CD Image 2-5 On-Axis / Off-Axis projection The position of the projector with r eference to t he screen may also be dif ferent depending on t he installation. Basically the projector can be positioned in On- Axis or Off-Axis con fi guration.
2. Gener al U +110% -29 % -1 03% + 17. 5 % D L R P F U D SIDE VIEW P F +110% -29% TOP VIEW P F L R -103% +17.5% Image 2-6 Shift ra nge PD M D F F ield o f view It’ s mechanical possible to shift out.
2. Gener al 2.5 Projector air inlets and out lets Air inlets and outlets Image 2-8 The CLM R10+ has 2 inlet channels and one air outlet. The air outlet is l ocated at the rear of the projector . The air inlets are located at the fr ont and top of the projector .
2. Gener al 18 R59770021 CLM R10+ 11/10/2010.
3. Physical i nstal lation 3. PHYSICAL INST ALLA TION About this chapter This chapter explains how to install and set up your CLM projector . If you are familiar with the projector and want to quickly set it up for temporary use, follow the “Quick setup” instructions below .
3. Physical i nstal lation Overview • RCU battery i nstallation • RCU rugged case installation • RCU XLR adaptor installation • Using the XLR adaptor of the RCU • RCU usage p ossibilities 3.
3. Physical i nstal lation 3.1.2 RCU rugged case installation Only with optional rugged case kit which is p art of the touring kit (R9861000). Necessary t ools No tools. Necessary p arts T ouring kit How to install the rugged case of the re mote control ? 1.
3. Physical i nstal lation S C S Image 3-6 Mounting the XLR adapte r 3.1. 4 Usin g the XLR ad aptor of the RC U How to use the XLR adaptor of the r e mote control unit ? 1. Connect a cable with XLR plug into the XLR adaptor . 2. Connect the other end of the cable with your CLM R10+.
3. Physical i nstal lation ab cd fg e Image 3-8 3.2 Le nses Overview • Available l enses • Lens selection • Lens formulas • Lens formulas 3.2.1 Available lenses Overview First series lenses: Image 3-9 R9849870 : CLD zoom lens (1.2 - 1.6 : 1) Image 3-10 R9861 100 : CLD zoom lens (1.
3. Physical i nstal lation Image 3-12 R9861060 : CLD zoom lens (1.2–1.5 : 1) Image 3-13 R9861070 : CLD zoom lens (1.5–2 .2 : 1) R9861071: CLD zoom lens (1 .5–2.2 : 1 ) HD Image 3-14 R9861080 : CL D zoom lens (2.2–4.4 : 1) Image 3-15 R98610890 : CLD zoom lens (4.
3. Physical i nstal lation SCR EEN SW PD Image 3-16 PD for lens selection 3.2.3 Lens fo rmulas Formulas Lens Throw r atio for CLM Metric formulas (meter) Inch formulas (inch) CLD (1.2 - 1.6 : 1) 1.2 - 1.6 PD min =1.216 x SW - 0.05 PD max =1.657 x SW - 0.
3. Physical i nstal lation 3.3 Alignment of a table m ounted CLM projector How to align a table mounted CLM projector 1. Place the projector in the des ired location. T ake into account the zoom range of the used lens and the siz e of the screen. 2. Project one of the internal hatch patter ns on the screen.
3. Physical i nstal lation A A B C Image 3-19 R i g g i n gs l o t sa n dc l a m p s Necessary t ools Open end spanner 17 m m Necessary p arts • Four rigging clamps (R855943) • Safety cable (B361213) • T wo snap hook locks (B361212) Mounting the rigging points into the handle 1.
3. Physical i nstal lation Image 3-20 Mount riggin g points X m m Image 3-21 x mm A B Image 3-22 Set up truss width 28 R59770021 CLM R10+ 11/10/2010.
3. Physical i nstal lation Image 3-23 Mounting ri gging cla mps Image 3-24 Opening cl am ps R59770021 CLM R10+ 11/10/2010 29.
3. Physical i nstal lation Image 3-25 Mounting to t russ Image 3-26 Security cable C AUTION : Always mount the saf ety cable when suspending the projector .
3. Physical i nstal lation How to align a ceiling mounted C LM projector 1. Install the projector in the desir ed location. See "Suspension of the CLM projector with rigging clamps", page 26. T ake into account the zoom range of the used lens an d the size of the s creen.
3. Physical i nstal lation 32 R59770021 CLM R10+ 11/10/2010.
4. Stacking CLM p roject ors 4. ST A CKING CLM PROJECTORS Stacki ng of CLM project ors is only possi ble with optio nal touri ng kit. See "Moun ting optional Carry han dle", page 20 9 for more i nformation . Overview • Stacking CLM projectors • Aligning stacked CLM projectors 4.
4. Stac king C LM pro jecto rs A B C D Image 4-2 Close the inter locking Image 4-3 Ceiling mo unted st acked proje ctors How to open an inte rlocking adapter 1.
4. Stacking CLM p roject ors D C B A Image 4-4 Open the interl ocking W ARNING : Never open an interlocking adapter o f a stacked projector w hich is still susp ended. First place the stacked projectors on the fl oor . 4.2 Aligning stacked CLM projectors How to alig n two st acked C LM project ors 1.
4. Stac king C LM pro jecto rs R o t a t i o n Image 4-5 Rotati on adjustme nt Inclination Image 4-6 Incl ination adjus tment Skew Q Image 4-7 Skew adj ustment Shift Image 4-8 Shift adjus tment 36 R59.
4. Stacking CLM p roject ors Zoom Image 4-9 Zoom adjustm ent R59770021 CLM R10+ 11/10/2010 37.
4. Stac king C LM pro jecto rs 38 R59770021 CLM R10+ 11/10/2010.
5. Connectio ns 5. CONNECTIONS About this chapter This chapter describes more in d etail the power (P), the input s ource (S) and the communication (C ) connections of the CLM R10+. C S P C Image 5-1 Overview • Power connection • Input source connec tions • Communication connections 5.
5. Connectio ns S H P Image 5-2 Power input W ARNING : Do not attempt operatio n if the AC supply an d cord are not within the spe ci fi ed voltage and power range.
5. Connectio ns Power input v oltage versus light output (for R90501005) Input power between 100V and 264V , the maximum light output with 4 l amps can be reached.
5. Connectio ns The CLM R10+ is st andard eq uipped wit h one 5 cable in put module and one DVI input module. 5.3 Communication connectio ns Communication interface 1 2 3 RS232 / 422 O UT RS232 / 422 .
5. Connectio ns IR communication (RC5) An IR receiver (L) is mounted on the comm unication interface. Note that there is also an IR receiver moun ted at the front and at the back of the projector .
5. Connectio ns 5 4 3 2 1 1 2 3 4 5 9 8 7 6 6 7 8 9 A B Image 5-1 1 A Pin num bering male DB–9 connecto r. B Pin num bering female DB-9 conn ector. RS232 An Electronic Industri es A ssociation (EIA).
5. Connectio ns DMX is used as communication bus between dif ferent devices in the light technic. Each device has an input and an output, so t hat the bus can be looped between the differ ent devices. According the standard a fi ve wire cable with XL R connector is used but mostly 3-wire cables are used.
5. Connectio ns 46 R59770021 CLM R10+ 11/10/2010.
6. Getti ng started 6. GETTING ST ARTED About this chapter This chapter describes t he functions on the remote control and local keypad and gives an overview how to start up the projec tor . It gives also a brief overview of the direct adjustment possible with these controls.
6. Get ting s tart ed MENU EXIT ENTER PAUSE TEXT PHASE TINT COLOR BRIGHTN CONTR 9 0 7 8 5 6 3 4 1 2 LENS LENS ZOOM LENS SHIFT LENS FOCUS 1 22 2 3 4 5 6 7 8 9 10 11 12 13 14 17 15 16 19 20 18 L SHARPN .
6. Getti ng started Ind. Key name Description 14 PHASE Us ed to remove the horizontal instabili ty of the image (usually for RGB source). It adjusts the phase of the pixel sampling c lock relative to the incoming signal. 15 FREEZ T o freeze the actual projected image.
6. Get ting s tart ed Starting image projection via the standby key . 1. Press Stand b y key once on the local keypad or on the remote control. (image 6-3) The projector status LED lights up. The projector start s up on t he last saved source. Some lamp and runtime warnings can be displayed when an i mage is displayed after a st art up.
6. Getti ng started Switc hing t o Standby . When the pro jector is runni ng and you want to go t o standby , press t he stand by key for 2 sec onds. Do not press any lo nger on the standby key ot herwise the pr ojec tor wil l resta rt. All custom settings are written to the internal backup device.
6. Get ting s tart ed F 1 F 2 F 3 F 4 F 5 A D J E X I T E N T E R P A U S E P H A S E T E X T S H A R P N T I N T C O L O R B R I G H T N C O N T R T R E B L E B A L A N C E B A S S V O L 9 0 7 8 5 6 .
6. Getti ng started Image 6-6 Press the LENS key to switch to another pattern. Different patterns are available. Quick sh ift adju stment 1. Press the LE NS key on the rem ote control or l oc al keypad. The zoom/focus menu will be displayed. (image 6-7) 2.
6. Get ting s tart ed AZ o o m B V ertical shi ft CF o c u s D Horizontal shi ft 6.5.3 Quick picture in picture Qui ck On - Of f Press on the PIP key on the remote control or the local keypad to activate the Load l ayout window. Use the ▲▼ key to scroll to the desired layout and press ENTER to activate.
6. Getti ng started When no digit is pressed after Rigging is pressed, the layout selection menu disappears after a few seconds wit hout a layout ch ange. 6.5.5 Quick language selection Language selection 1. Press Menu to acti v ate the menus and select with the ▲ or ▼ k ey Projector Control and press ENTER .
6. Get ting s tart ed Image 6-16 T o continue using the RCU with that speci fi c address, it is necessary to enter the sam e address with the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key .
6. Getti ng started 6.8 Source sel ection Source se lection w hen no pic ture in pict ure is activ e Use the digit keys on the remote control or local keypad to active the des ired source.
6. Get ting s tart ed Sharpness The sharpness function is used to adjust the im age sharpness of video signals. Use the + button for more sharpness Use the - button for less sharpness Phase Use the + or - side of the phase contr ol button to adjust the phase.
7. Sta rt up of t he A djust ment m ode 7. S T ART UP OF THE ADJUST MENT MODE Overview • About the adjustme nt mode • About the use of the remote control and the l ocal keypad • Start up the adjustment mode • Navigation and adjustments • On screen menus versus LCD display menus • T est patterns in adjustment mode • Menu memor y 7.
7. St art up of the A djustme nt mode Image 7-1 7.4 Navigation and adjustments How to na vigate in the me nu struct ure? On ce in th e me nu s tru ctu re, u se t he ▲ or ▼ keys on the remote control ( or the ▲ or ▼ (+ or -) key on the local keypad) to scroll through the items in the displayed menu.
7. Sta rt up of t he A djust ment m ode 7.6 T est patterns in adjustment mode Overview When the adjustment mode is started, a test pattern can be called at any moment just by pressing the P attern key on the RCU or the local key path. Press as many times on the Pattern key as necessary to display the desired test pattern.
7. St art up of the A djustme nt mode 62 R59770021 CLM R10+ 11/10/2010.
8. Inpu t menu 8. INPUT MENU Overview •O v e r v i e w fl ow • Slot module type • Input locking • Minimum delay • Native resolution • Source switching • No signal 8.
8. Inp ut menu C AUTION : Always install a cover plate on an unused input slot. T his to prevent dust intrusion into the pro- jector . 8.2.2 Input con fi gur ation How to change? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Input and press ENTER .
8. Inpu t menu Input module Indication Descripti on RGB SOG RGB input with sync on green YUV HS/VS - CS Component v ideo with separate horizontal and vertical sync o r separate composite sync.
8. Inp ut menu When: Free run Output is locked on an i nternal sync (60 Hz) Automatic Output is l oc ked on the selected input for the main window Input 1 Output is locked on source 1 Input 2 Output is locked on source 2 The options menu changes depending on the selection.
8. Inpu t menu Genlock off (default position) locking done on input s ource of main window , when automatic was selected or on the selected input source when a speci fi c input was selected. Projector detects automatically the vertical frequency and clock frequency of the input si gnal.
8. Inp ut menu Image 8-13 When the show native resolution function is in the ON position, the projector handles the source as follows: Source Projected image Name Ratio Resolution Ratio Resolution XGA.
8. Inpu t menu 8. 6 Sourc e swit chi ng Switching from one s ource to another T o minimize undesired ef fects when switching fr om one source to another one can use the switching mode, using the fade effect . Image 8-16 Example of fade effe ct Switching mode se t up 1.
8. Inp ut menu The Input menu is displayed. 3. Use the ▲ or ▼ key to select No signal an d press ENTE R to toggle between [Black] and [Blue]. (imag e 8-20, image 8-21, image 8-22) Image 8-20 Image 8-21 Image 8-22 8.7.2 Shutdown s etting How to change the shutdown setting 1.
8. Inpu t menu Image 8-26 Image 8-27 Image 8-28 R59770021 CLM R10+ 11/10/2010 71.
8. Inp ut menu 72 R59770021 CLM R10+ 11/10/2010.
9. Imag e menu 9. IMAGE MENU Overview •O v e r v i e w fl ow • How to select the i mage adjustments? • Image Settings • Aspect ratio •T i m i n g s • Image fi les services • Save custom settings 9.
9. Im age men u Level 1 Level 2 Level 3 Level 4 V ertical start Advanced settings Clamp delay Clamp width Field polarity Film mode detection Image fi le services Manual load Delete Delete all Rename Copy Options Load fi le Save cust om setting s 9.2 How to select t he image adjustments? Start u p 1.
9. Imag e menu 9.3.1 Con trast About Contrast The contrast function is used to adjust the contrast between the light and dark areas of the displayed image. How to change the contrast? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press EN TER .
9. Im age men u Image 9-7 Image 9-8 Image 9-9 Image 9-10 9.3.3 Sat uration About (color) saturation The color function is used to adjust the c olor saturation levels. How to change t he saturation? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press EN TER .
9. Imag e menu 9.3.4 Tint (hue) About Ti nt The Tint f unc tion is used to adjust color hue to obtai n true color reproduction and is only active for Video and S-V ideo when the NTSC color system is used. For P AL an d SECAM sources, Ti nt is not accessible.
9. Im age men u 2. Use the ▲ or ▼ key to select Image and press EN TER . 3. Use the ▲ or ▼ key to select Image settings and press ENTER . 4. Use the ▲ or ▼ key to select Phase and press ENTER . The Phase progress bar appears. 5. Use ◄ or ► to change the phase a nd re fi ne the jitter .
9. Imag e menu Image 9-27 9.3.7 Noise re duction About Noise reduction Reduces noise and pixel jitter in all video sources. How to change? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press EN TER . 3. Use the ▲ or ▼ key to select Image settings and press ENTER .
9. Im age men u Color temperature selection is only possible when Color space is OFF Color temperatur e The coloration (reddish, white, bluish, greenish, etc.) of white in an image, measured using the Kelvin (degrees K) temperature scale. Higher temperatures output more light.
9. Imag e menu 3. Use the ▲ or ▼ key to select Image settings and press ENTER . 4. Use the ▲ or ▼ key to select Color tem perature and press ENTE R . 5. Use the ▲ or ▼ key to select Cust om bal ance and press ► . The G ain adjustment bar scales are displayed.
9. Im age men u B Black lev el 0.7V Image 9-41 Bla ck leve l Δ G ΔΒ Δ R R G B Image 9-42 One can conclude here t h at a good col or tracking can only be met by using three p reviously (i nput) bal.
9. Imag e menu 9.3.9.2 Adjusting the input balance How can it be done ? T o balance the three color signals of a particular source there are conditions; in fac t we must k now the black and the white level of the source i .
9. Im age men u 9. T oggle with ▲ or ▼ key t o Black balance blue and adjust the blue black level on a minimal value. Note: This minimal value is not necessary , provided that the 2 other colors a.
9. Imag e menu Image 9-51 Image 9-52 Image 9-53 Image 9-54 Image 9-55 9.4 Aspect r atio What can be done? The aspect ratio setting for ces the projector to project an image using a de fi ned aspect ratio Aspect ratio Description 4:3 Standard television format 16:9 Wide screen television for mat / anamorphic format 5:4 Workstation format 2.
9. Im age men u 4/3 5/4 16/ 9 Video Signal Pal/Secam Video Sig nal NTSC Video Signal 16/9 4/3 RGB Signal Image 9-56 Some exampl es for aspect r atio How to select an Aspect ratio? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press EN TER .
9. Imag e menu The Custom aspect ratio dialog box opens. 2. Use the ▲ or ▼ key to adjust the vertical siz e of the image. Use t he or key to adjust the horizontal size of t he ima ge. When the desired aspect ratio is obtained, press EXI T . (image 9-6 0, image 9-61) Image 9-60 Image 9-61 9.
9. Im age men u Image 9-62 Image 9-63 Image 9-64 Image 9-65 9.5. 2 Advan ced sett ings About the advanced settings Clamp delay The time between the leading edge of the clamp pulse and the l o cked edge of the sync pulse. Can be any value between 0 and 255.
9. Imag e menu 5. Use the ▲ or ▼ key to s elect Clamp delay or Clamp width and press EN TER . A progress bar appears. 6. Use the ▲ or ▼ key to change the s etting. (im age 9-67, image 9-68, image 9-69, image 9-70) Image 9-67 Image 9-68 Image 9-69 Image 9-70 How to change the fi eld pol arity? 1.
9. Im age men u Image 9-74 9.5. 3 Adv ance d set ting s, fi lm mode detection About fi lm mode detection This mode detects whether fi lm or video is displayed.
9. Imag e menu Image 9-75 Image 9-76 Image 9-77 Image 9-78 9.5.4 Advanced setting, b rilliant color look What can be done ? The BrilliantColor™ technology is con fi gured to process the spok e regions of the color w heel as a secondary c olor which improves the brightness of the display and gives the viewer a truly lif e- like image.
9. Im age men u Image 9-79 Image 9-80 Image 9-81 Image 9-82 9.6 Image fi le s services Overview • Files and fi le manipulations • Manual Load fi le • Delete fi le • Delete all custom fi les • Rename a fi le • Copy a fi le • File options 9.
9. Imag e menu 9.6. 2 Manu al Load fi le How to load? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press EN TER . 3. Use the ▲ or ▼ k ey to select F ile services and press EN TER . The F ile service m enu is displayed.
9. Im age men u 5. Use the ▲ or ▼ key to select the fi le which must be deleted. Note: Only custom fi les can be deleted. 6. Press ENT ER to delete the selected fi le. (image 9-87, image 9-88, image 9-89, image 9-90) Image 9-87 Image 9-88 Image 9-89 Image 9-90 No recovery possible ! 9.
9. Imag e menu Image 9-94 9.6. 5 Rename a fi le How to renam e? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press EN TER . 3. Use the ▲ or ▼ k ey to select F ile services and press EN TER . The F ile service m enu is displayed.
9. Im age men u 2. Use the ▲ or ▼ key to select Image and press EN TER . 3. Use the ▲ or ▼ k ey to select F ile services and press EN TER . The F ile service m enu is displayed. 4. Use the ▲ or ▼ key to s elect Copy and press ENTE R . The copy window opens.
9. Imag e menu Image 9-105 Image 9-106 Image 9-107 Image 9-108 Image 9-109 9.7 Save custom settings What is done? The current custom settings c an be saved to the internal b ackup device in the same way as it would be done when the projector was switched to standby .
9. Im age men u 98 R59770021 CLM R10+ 11/10/2010.
10. Lay out m enu 10. LA YOU T MENU Overview •O v e r v i e w fl ow • Main window • PIP window • Layout fi le services 10.1 Overvi ew fl ow Overview Level 1 Level 2 Level 3 Level 4 Layout M.
10. Lay out m enu Image 10-1 Image 10-2 The fi rst character is highlighted. Use the ▲ or ▼ key to select the desir ed character and press or key to selec t the next character in the name.
10. Lay out m enu Image 10-7 Size adjust ment main window A wi dth adjust ment B hei ght adjustment The size can be changed with res pect to the original aspect ratio. How to adjust with respect to the original aspect ratio? 1. Press MENU to activate the menus.
10. Lay out m enu Image 10-1 1 Image 10-12 How to adjust height and width separately? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Layout and press ENTER . 3. Use the ▲ or ▼ key to select M ain Window and press ENTER . The main window opens.
10. Lay out m enu 10.2.3 Position adjustment What can be done? The main window can be repositioned on the screen. The upper left corner is the reference. Image 10-18 Positioning the window How to position? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Layout and press ENTER .
10. Lay out m enu 10.3 PIP window Overview • Introduction t o PIP • Picture in Picture activation • Picture in Picture source s election • Picture in Picture size of the window • Picture in Picture, position window 10.
10. Lay out m enu Image 10-25 Image 10-26 Image 10-27 When PIP is activated (ON state), the PIP window becom es the active window. Switching to the m ain window is sti ll possi ble with the wi ndow button on the RCU. 10.3.3 Picture in Pict ure sour ce selectio n What can be done ? The input source for the picture in picture window c an be selected.
10. Lay out m enu 10.3.4 Picture in Pi cture size of the wi ndow What can be done? The width and height of the picture in picture window can be changed till the desired dimensions are obtained.
10. Lay out m enu Image 10-34 Image 10-35 Image 10-36 Image 10-37 Image 10-38 How to chang e the heigh t and width sep arately ? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Window and press ENTER . 3. Use the ▲ or ▼ k ey to s elect PIP Window and press ENTER .
10. Lay out m enu Image 10-42 Image 10-43 10.3.5 Picture in Picture, position window What can be done? The picture in picture window can be p osition on any place on the display just by changing its start coordinates. The reference is the upper left c orner of the window .
10. Lay out m enu 10.4 Layout fi le services Overview • Load layout • Rename a layout • Delete a layout • Copy / Save as a layout 10.4.1 Load layout When loading a layout which required two sources, the PIP wind ow On/Of f setting will be switched to ON.
10. Lay out m enu 10.4.2 Rename a layout Only custom created layouts can b e renamed. How to renam e? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Window and press ENTER . 3. Use the ▲ or ▼ key to select Layout and press ENTER .
10. Lay out m enu 4. Use the ▲ or ▼ key to select Delete and press ENTER . The Del ete window opens. (image 10-57, image 10- 58, image 10-59, image 10-60) The fi rst 3 layouts ar e default layouts and cannot be delete. 5. Use the ▲ or ▼ k ey to select the layout t hat mus t be deleted.
10. Lay out m enu Image 10-61 Image 10-62 Image 10-63 Image 10-64 112 R59770021 CLM R10+ 11/10/2010.
11. Lam p menu 11 . L A M P M E N U Overview •O v e r v i e w fl ow • Lamp power m ode • Lamp pow er • Lamp Identi fi cation • Status and run time overview lamps • Lamp mode 1 1.
11. Lamp men u How to switch? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key t o se lect Lamp and press ENT ER . 3. Use the ▲ or ▼ key to select Power and press ENTER . 4. Use the ▲ or ▼ key to select Mo de . 5. Press ENT ER to toggle between [Normal] , [Economic] , [Normal high altitude] and [Eco high altitude ].
11. Lam p menu Image 1 1-7 About over-temperature prot ection When the projector software detects a too high lamp temperature it automatically reduce the lamp power with 20%.
11. Lamp men u 1 1.5 Status and run t ime overview la mps Overview 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key t o se lect Lamp and press ENT ER . 3. Use the ▲ or ▼ key to select Overview and press ENTE R . The status and the r un time for each lam p are displayed.
12. Al ignme nt menu 12. A LIGNMENT MENU About this chapter This chapter describes the ali gnment of the projector once the physical i nstallation is fi nished.
12. Ali gnmen t menu Level 1 Level 2 Level 3 Full screen green Full screen red Full screen white Hatch Outline Purity ScenergiX Color space Projector EBU SMPTE Custom White peaking ScenergiX Status White level Bottom Black level Show pattern Reset 12.
12. Al ignme nt menu For more i nformation about t he physi cal ins tall ation, see ch a pter “Genera l”, “P roject or con fi gurati ons”. 12.3 Lens adjustment Quick way to enter the lens adjustment setting; press the lens button o n the local keypad or the remote control.
12. Ali gnmen t menu Image 12-9 Image 12-10 12.4 Side keystone What can be done? The side keystone adjustment is used to align the image if t he projector is mounted at a non standard projection angle. Image 12-1 1 Side keystone A Key stone adjust ment wi th posi tive valu es B Key stone adjustment with negative val ues Side keystone adjust ment 1.
12. Al ignme nt menu 12.5 Blanking What can be done ? Blanking adjustments affect only the edges of the pro jected i mage and are used to frame the projected image on to the screen and to hide or black out unw anted information (or nois e ). A ’0’ on the bar scal e indicates no blanking.
12. Ali gnmen t menu Image 12-16 Image 12-17 Image 12-18 12.6 Intensity What ca n be don e The light i n the optical light pat h can be dimmed w ith a mec hanical shutter plate.
12. Al ignme nt menu 3. Use the ▲ or ▼ key to select Gamma and press ENTER . The Gamma prog ress bar appears. 4. Use ◄ or ► key to change the gamma setting and press EXIT . Gamma c an be set to one of t h e 8 available steps. (im age 12-22, image 12-23, image 12-24) Image 12-22 Image 12-23 Image 12-24 12.
12. Ali gnmen t menu Image 12-25 Image 12-26 Image 12-27 12.9 Color space Color space A color space or color standard is a mathematical representation for a color .
12. Al ignme nt menu Image 12-28 Image 12-29 Image 12-30 Image 12-31 When selecting a fi xed color space, the values of this selected color space overwrite the custom selected color space. 12.10 White peaking About white peak and brilliant c olor In video centric applications true color reproduction is generally a priority over brightness.
12. Ali gnmen t menu Image 12-32 Image 12-33 Image 12-34 12.1 1 ScenergiX Overview • Introduction • Preparations • ScenergiX activation • ScenergiX pattern • ScenergiX overlap zone (horiz on.
12. Al ignme nt menu Adjustable overlappi ng area 50% 100% 50% 100% image 2 image 1 image 2 image 1 Light output per im age Total composite light output Image 12-36 Scenerg iX Basic P rinciple 12.
12. Ali gnmen t menu 12.1 1.4 ScenergiX p attern What can be done? T o make the ScenergiX adjustment more eas y , an internal patter n can be displayed. How t o disp lay or r emo ve the p atter n? 1. Use the ▲ or ▼ key to select Show pattern and press ENTER .
12. Al ignme nt menu Overlap : number of pixels that over lap Horizontal res olution of 1 projector T otal horizontal s creen resolution : [(horizontal resolution of 1 pr ojector) x 2] m inus overlap. Horizontal Resolution source : nu mber of active pixels of the source.
12. Ali gnmen t menu Image 12-51 Image 12-52 12.1 1.6 Sce nergiX o verlap zo ne (verti cal Sce nergiX) De fi nitions Image 12-53 Scenergi x overlap zone verti cal Overlap : number of pixels that over.
12. Al ignme nt menu Image 12-57 How to set for the second projector 1. Go to Layout → Main window → Size 2. Enter the value for the W idth as foll ow: T otal V ertical screen resoluti o n / 2 - 0.
12. Ali gnmen t menu 5. Use the ▲ or ▼ k ey to select one of the f our size adjustments and press ENT ER . (image 12-63, image 12-64, im age 12-65, image 12-66) A pattern with the dif ferent areas is displayed. (image 12-67) 6. Use the cursor keys to move the border of the overlap area to the desired position.
12. Al ignme nt menu Image 12-68 Width set up for p rojector 1 Image 12-69 Width set up for p rojector 2 12.1 1.8 Adju sting th e black l evel of the imag es Why black le vel adjus tment For dark images, the overlap zone will be brighter then the r est of the images.
12. Ali gnmen t menu Image 12-70 DLP Leakage area set up After the area is set, use TEXT key to remove the area border lines when adjusting the black level. How to set the leakage a rea wid th 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Alignment and pr ess ENTER .
12. Al ignme nt menu Image 12-74 Image 12-75 DLP leakage are a 1 Overlap area 2 DLP Leakage area How to adjust 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Alignment and pr ess ENTER . 3. Use the ▲ or ▼ key to select ScenergiX and press ENTER .
12. Ali gnmen t menu Image 12-76 Image 12-77 Image 12-78 Image 12-79 A C B 12 13 11 R G B RGB Imag e 1 Imag e 2 Image 12-80 Black le vel adjustment Use the Reset func tion to b ring all S cene rgiX se ttings b ack to zer o.
13. Pro jector contr ol 13. P ROJECTOR CONTROL About this chapter This chapter explains the set up of the control part of the software such as projector address and all types of communication with the external world.
13. P roject or contr ol Level 1 Level 2 Level 3 Menu [Center] Bar sca le [Bott om] Local LCD c ontrast Language English Français Deutsch Español Italiano 13.
13. Pro jector contr ol Image 13-4 13.2.2 Common addr ess About common address A common address can be ’0’ or ’1’. Any command coming from a remote control pr ogrammed with that common address will be executed. How to change the common addres s? 1.
13. P roject or contr ol How to set up? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Projector control and press ENTER . 3. Use the ▲ or ▼ key to se lect Serial communication and press EN TER . The serial communication menu opens.
13. Pro jector contr ol 13.3.3 RS422 termi nation What can be done? When the interface standard is set to RS4 22, the last projector in a line should be R S422 terminated (ON position). A ll others in the line should be in the OFF position. How to set 1.
13. P roject or contr ol Default Gateway A router that serves as an entry point into and exit point out of a network. For example, a local network (LA N) may need a gateway to connect it to a wide area network (W AN) or t o the Internet. MAC address Media Access Control address.
13. Pro jector contr ol 4. Use the ▲ or ▼ key to select IP-address and press ENT ER to select. Note: An address contains 4 octet s with a maximum value of 255. This must NOT be 0.0.0.0 for static IP-Address assignment. 5. Use the ▲ or ▼ key to select the desired digit and press ◄ or ► k ey to select the next digit in the address.
13. P roject or contr ol Image 13-28 13.4.5 Default G ateway set up How to set up? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Projector control and press ENTER . 3. Use the ▲ or ▼ key to select Network and press ENTER .
13. Pro jector contr ol 4. Use the ▲ or ▼ key to select the de sired IR receiver and press ENTE R to toggle this receiver [on] or [off]. (image 13-33, image 13-34, im age 13-35) Image 13-33 Image 13-34 Image 13-35 Activatio n key 1. Use the ▲ or ▼ key to select A c tiva tio n key and press ENTER .
13. P roject or contr ol Or , enter a new value with t he digit keys on the remote control or l ocal keypad. 6. Use the ◄ or ► k ey to select the next digit and r epeat step 5. 7. When the desired address is entered, press EN TER to store that address.
13. Pro jector contr ol Image 13-45 13.6.3 DMX monitor What can be done? If a DMX device is connected, t he se ttings per channel can be display ed in an on screen menu. How to start up the monitoring 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Projector control and press ENTER .
13. P roject or contr ol Image 13-50 When selecting DMX monitor and no DMX device is connected, the message “No DMX data, check conne ction <ENTER> to d isplay channels” appears on the s creen. When ENTE R is pressed the sam e window appears as DMX Monitor but without values.
13. Pro jector contr ol 3. Use the ▲ or ▼ key to select DMX and press ENTER . 4. Use the ▲ or ▼ key to select DMX mode and press EN TER to toggle between [Basic] and [Full]. (image 13-51, image 13-52, image 13-53) Image 13-51 Image 13-52 Image 13-53 13.
13. P roject or contr ol The function can be: • Auto align (only aligning of the pr eview window is executed). • Auto-image menu. T his function opens a auto image menu where the user can make his choice between auto align, auto contrast/bright nes s and auto phase.
13. Pro jector contr ol Image 13-63 13.8 Menu position What is possible? The on screen menu and the bar scale can be positioned on dif fe rent places on the scr een. Both can be positioned : • Center •T o p • Bottom How to change the position? 1.
13. P roject or contr ol Image 13-67 Image 13-68 Image 13-69 13.1 0 Lang uage s ele ctio n What can be done? The user can change the language of the on s creen menus and the local display menus to one of the available languages.
14. Ser vice m enu 14. S ER VICE MENU About this chapter This chapter refers t o the Service menu in which the owner can fi nd valuable information when calling the Barco help desk.
14. Ser vice menu The following items will be displayed : •T y p e o f p r o j e c t o r • Projector address • Package •C o n fi guration • Baud rate • IP address • MAC address •T e x t • Serial number of proj ector: this numb er can be useful w hen calling for technical as sistance.
14. Ser vice m enu 14.3 Diagnosis What ca n be seen? The diagnosis menu gives the poss ibility to get an overview of the working of the projector . 14.3.1 How to start up the diagnosis? Start u p 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER .
14. Ser vice menu Image 14-1 1 Use the ▲ or ▼ item in the menu to select the previous or next page with information. 14.3.3 V oltages How to di splay an ov ervi ew? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER .
14. Ser vice m enu 14.3.4 I²C diagnosis How to select? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER . The service window opens. 3. Use the ▲ or ▼ key to select Diagnosis and press EN TER . The diagnosis screen is displayed.
14. Ser vice menu Image 14-20 Image 14-21 Image 14-22 Image 14-23 Use the ▲ or ▼ item in the menu to select the previous or next page with informatio n. 14.3.6 Fan speed s overv iew How to ge t an over view? 1. Press MENU to activate the menus. 2.
14. Ser vice m enu Image 14-27 Use the ▲ or ▼ item in the menu to select the previous or next page with information. 14.3.7 SPI How to g et an over view 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER .
14. Ser vice menu 3. Use the ▲ or ▼ key to select Diagnosis and press EN TER . The diagnosis screen will be displayed. 4. Use the ▲ or ▼ key to sel ect Error logging and press EN TER . The Error logging overview menu is displaye d. For more explanation about the st o red error message, see "Error codes", page 203.
14. Ser vice m enu The service window opens. 3. Use the ▲ or ▼ k ey to select Res tore factory defaults and p ress ENTER . The factory defaults con fi rmation window opens. 4. Use the ▲ or ▼ key to select the setting to exclude and press EN TER to toggle between [No] and [Y es].
14. Ser vice menu The service window opens. 3. Use the ▲ or ▼ key to se lect Save c ustom settings and press ENTER . The custom settings are writt en to the internal backup device. A message menu “Save data ...” is di s played during the s ave operation.
14. Ser vice m enu 14.8 USB memory What is possible with an USB device? An USB device, F A T 16 formatted can be used, to save custom settings from the projector or to load custom settings to the projector . This function is ver y handy to clone projectors.
14. Ser vice menu Load custom settings 1. Connect a F A T 16 formatted USB device to the USB port. 2. Press MENU to activate the menus. 3. Use the ▲ or ▼ key to select Service and press ENTER . The service window opens. 4. Use the ▲ or ▼ key to select USB m emory and press ENTER .
14. Ser vice m enu Image 14-55 Image 14-56 Image 14-57 R59770021 CLM R10+ 11/10/2010 165.
14. Ser vice menu 166 R59770021 CLM R10+ 11/10/2010.
15. Mainte nance 15. MAI NTENA NCE About this chapter This chapter contains detail ed maintenance procedures like lens cleaning, etc. These procedures can easily be performed by the operator of the projector . Overview • Cleaning the lens • Cleaning the exterior of t he projector • Level check of cooling liquid 15.
15. Mainte nance W ARNING : Switc h off t he projector a nd pull out the po wer cord be fore st arting t he check pr ocedure ! How to check Remove : - lamp door , see "Removal of the lamp door", page 182. - front cover , see "Removal of the front cover", page 181.
16. Ser vic ing 16. SER VICING About this chapter This chapter contains general servicing procedures like lamp replacement, input unit replacement etc. Note that some of these procedures may only be performed by quali fi ed technical service personnel.
16. Ser vicin g A B Image 16-1 Filter top re placem ent C AUTION : Never install a used HEP A fi lter . Always install a n ew HEP A fi lter . C AUTION : Never use t he projector wit h a removed cover .
16. Ser vic ing A B C Image 16-2 Front fi lter replacem ent C AUTION : Never install a used HEP A fi lter . Always install a n ew HEP A fi lter . C AUTION : Never use t he projector wit h a removed cover . Always reinstall the r e moved cover . 16.
16. Ser vicin g B C A Image 16-3 Mounting the lens C AUTION : Never transport the projector with a Lens mounted in the Lens Holder . Always remo ve the Lens before transporting the projector . N eglecting this can damage the Lens Holder and Prism . 16.
16. Ser vic ing A Image 16-5 Slide out lens 16.5 Removal of a lamp unit W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service personnel. C AUTION : Never at tempt to disassemble the lamp f rom its housing or t o dispose of it.
16. Ser vicin g Mercur y V apor Wa rnings : The lamp used in the projector contains mercury . In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors: • Ensure the projector is installed only in ventilated rooms.
16. Ser vic ing Image 16-9 T ake out the lamp For recycling guidelines of the lamp, see "Recycling guidelines", page 8. 16.6 Mounting a new lamp unit About the lamp units All four lamp units are equal. A spare lamp can be inserted in any position without problems.
16. Ser vicin g Image 16-10 Lamp ins ertion 16.7 Removal of an input module Necessary t ools Phillips screw driver PH1 How to remove an input module 1. Switch off t he projec tor and unplug the power cord at t he projector side. 2. Release the two captive screws of the input module.
16. Ser vic ing C AUTION : Ensure that an unused slot is always covered w ith a dummy front plate. Imm ediately install af ter removi ng an input module a new in put module or a dummy f ront cover . 16.8 Inserting an input module Necessary t ools Phillips screw driver PH1 How to insert an input module 1.
16. Ser vicin g 6. Turn out the third lid using the back of the main lid. (image 16 -14) 7. T op-up the reservoir with cooling liquid unti l the level is somewhat higher than the hole in the res ervoir . (image 16-15) 8. Close the third lid again using the back of the m ain lid.
16. Ser vic ing Image 16-15 T op-up reservoir 2 cm Image 16-16 Pressurize circuit R59770021 CLM R10+ 11/10/2010 179.
16. Ser vicin g 180 R59770021 CLM R10+ 11/10/2010.
17. P rojec tor cov ers, removal and ins tallat ion 17. PROJECTOR COVERS, REMOV AL AND INST ALLA TION Overview • Removal of the front cover • Removal of the lamp door • Removal of the back cover.
17. Pro jecto r covers, rem oval and in stall ation b c Image 17-2 Remove the front cover 17.2 Removal of the lamp door W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service personnel. Necessary t ools Flat screwdriver How to remove the lamp door 1.
17. P rojec tor cov ers, removal and ins tallat ion Image 17-4 Remove lamp door 17.3 Removal of the back cove r Necessary t ools Flat screwdriver How to remove the back co ver 1. Release the 3 captive screws in the back cover . (image 17-5) 2. Pull off the bac k cover .
17. Pro jecto r covers, rem oval and in stall ation Image 17-6 Remove back cover 17.4 Removal of the top cover T o remove the top cover, fi r st remove the f ront a nd back cove r and th e lamp door . Necessary t ools Flat screwdriver How to remove the top cover 1.
17. P rojec tor cov ers, removal and ins tallat ion Image 17-8 Loosen screws Image 17-9 Side cover rem oval 17.6 Installation of the side cover Necessary t ools Allen wrench 3 mm How to install 1. Hook the side cover on the fi xation screws and pull the cover downwards until it matches with the bottom cover .
17. Pro jecto r covers, rem oval and in stall ation Image 17-1 1 Fixate side cover 17.7 Installation of the top c over How to install 1. Place the top cover on the projector and push on the front si de and back side of the cover until it cl icks into its locks (4 locks).
17. P rojec tor cov ers, removal and ins tallat ion Image 17-14 Secure back cover 17.9 Installa tion of t he front cover Front cover can only be installed after that the side covers and top cover are installed. Necessary t ools Flat screwdriver How to install the front cover 1.
17. Pro jecto r covers, rem oval and in stall ation A B Image 17-15 Install front cover C Image 17-16 Secure front cover 17.10 Installa tion of the lamp door Lamp door can only be installed when the top cover is installed. Necessary t ools Flat screwdriver How to install the lamp door 1.
17. P rojec tor cov ers, removal and ins tallat ion A A B Image 17-17 Lamp door i nstallati on Image 17-18 Secure t he lamp d oor R59770021 CLM R10+ 11/10/2010 189.
17. Pro jecto r covers, rem oval and in stall ation 190 R59770021 CLM R10+ 11/10/2010.
A. Dimens ions A. DIMENSIONS Overview • Dimensions of the CLM R1 0+ A.1 Dimensions of the CLM R10+ Dimensions without carry handle 691.18 4 4 2 . 0 3 2 9 3 .
A. D imensio ns Dimensions with optional carry handle 392.55 515 257.5 257.5 775 532 145.5 97.5 305 105 105 Image A-2 192 R59770021 CLM R10+ 11/10/2010.
B. Standa rd Sour ce Files B. ST ANDARD SOURCE FILES B.1 T ab le over view Ta b l e o v e r v i e w The following standar d image fi les are pre-programmed in the projector .
B. St andard S ource F ile s Name 1 Fvert Hz 2 FHor kHz 3 Fpix MHz 4 Ptot 5 Pact 6 Ltot 7 Lact 8 1400x1050RB@6 0 59,946 64,742 100,997 156 0 1400 1080 1050 1600x1200@60 60,001 75,002 162,004 216 0 160.
C. DMX Chart C. DMX CHART Overview • CLM c ontrol channel mapping (Full m ode) • CLM control channel mapping (Basic mode) C.1 CLM control channel mapping (Full mode) Overview Chan- nel Functi o n .
C. DMX Cha rt Chan- nel Functi on T ype Range Defaul t Action Comments 0-3 1 S t o p 31 - 63 Run 64 - 95 Future assignment Same as Stop 96 - 127 Future assignment Same as Stop 128 - 159 Future assignm.
C. DMX Chart Chan- nel Functi on T ype Range Defaul t Action Comments 0 - 7 No function 8 - 1 5 Activate Layout 1 (Main full screen) If held for 2 Sec 16 - 23 Act ivate Layout 2 (PiP top right) If hel.
C. DMX Cha rt 198 R59770021 CLM R10+ 11/10/2010.
D. Spec ificat ions D. SPECIFICA T IONS Overview •S p e c i fi cations C LM R10+ •S p e c i fi cations CLM 5 cable input (multi purpose) •S p e c i fi cations CLM HDSDI – SDI input •S p e c i fi cations CLM DV I input •S p e c i fi cations CLM DVI H DCP input D.
D. Specifi cations Orien tation t able/ceiling/side (portrait)/ verti cal Po wer cons um ption 1,600 W Resolution 1, 400 x 1,050 pixels (S XGA+) Safe ty Reg ulation s Compliant with UL1950 and EN60950 ScenergiX Horizontal and vertical edge blending Weight 30kg (excluding lens and ri gging frame) D.
D. Spec ificat ions • Signal requirements: - Component Video (BNC) o R-Y : 0,7Vpp ±3dB 75 Ohm termination. o Ys : 1Vpp ±3dB (0,7V Lum a +0,3V Sync) 75 Ohm termination. o B-Y : 0,7Vpp ±3dB 75 Ohm termination. -R G ( s ) B o R : 0,7Vpp ±3dB 75 Ohm termination.
D. Specifi cations D.4 Speci fi cations CLM DVI input Input front view Sync OK Sel DVI inpu t Image D-3 Speci fi cations • DVI type: DVI-I (DV I-Integrated) , but the analog signals are not supported.
E. Trou ble shooting E. TROUBLESHOOTING E.1 Error codes Overview When the error code i s preceded by a ’-’ sign, then the error means a real error f or the projector . When the error code is preceded by a ’+’ sign, then the error code means a warning.
E. Tr ouble shooti ng Error code Description Error Warning Caused by Acti on 4198 FP GA P MP i nit failed Ye s - 6099 Board ID unkown version Ye s 6098 Board ID invalid string Ye s 7999 DMD temp low Y.
E. Trou ble shooting Error code Description Error Warning Caused by Acti on 7908 Fan inlet A low Y es Y es Fan is run ning too slow or not at all If problem persists, call a quali fi ed service engin.
E. Tr ouble shooti ng Error code Description Error Warning Caused by Acti on 7862 Lamp 1 run tim e sht dw n exceeded - Ye s 7861 Lamp 2 run ti me msg exceeded - Ye s Run time of lamp 2 will be exceeded Replace the lamp with a new one.
E. Trou ble shooting Error code Description Error Warning Caused by Acti on 9399 Error image 9398 Maximum image fi les reached Y es No Reac hing the maximum allowed number of fi les Delete some unne.
E. Tr ouble shooti ng 208 R59770021 CLM R10+ 11/10/2010.
F. Moun ting opt ional Ca rry han dle F . MOUNTING OPTIONAL CAR R Y HANDLE About this chapter This chapter describes the procedures to mount the optional carr y handle to CLM projector . When this optional carry handle i s mounted, the projector can be suspended with the rigging c lamps and stacking of projector is possible.
F. Mounti ng opti onal Car ry handl e A A A B B C Image F-2 Mounting th e stacking poi nts Image F-3 Stacking poi nts mounted F .2 P reparing the new carry handle What has to be done? The back stacking point m ust be removed before the carry handle can be mounted on t he C LM projector .
F. Moun ting opt ional Ca rry han dle Image F-4 Remove stacking point construction F .3 Preparing th e projector C AUTION : Before turning the projector upside down, be sure the stacking points on the top cover are mounte d.
F. Mounti ng opti onal Car ry handl e 1 2 3 Image F-5 1 Image F-6 F .4 Mounting the carry handle Necessary t ools • 8 mm Allen wrench. • 4 mm Allen wrench. • 2,5 mm Allen wrench. Necessary p arts • One spacer rotation ring. •O n e fl at spacer .
F. Moun ting opt ional Ca rry han dle 1 2 3 1 4 5 Image F-7 Image F-8 R59770021 CLM R10+ 11/10/2010 213.
F. Mounti ng opti onal Car ry handl e 214 R59770021 CLM R10+ 11/10/2010.
G. Order in fo G. ORDER INFO G.1 Spare part order info Order info: Order info Description R9854430 5 cable input module R9854450 HDSDI - SDI input m odule R9854460 DVI input module R848607 Cover plate.
G. Order in fo 216 R59770021 CLM R10+ 11/10/2010.
Glos sary GLOSSAR Y 2:2 p ull- down The process of transferring 24-fr ames/sec fi lm format into video by repeating each frame (used for P AL DVD ’s) as two video fi elds.
Glos sary MAC address Media Access Control address. Unique hardware numbe r , used in combination with the IP-address to connect to the network (LAN or W AN). PiP PiP stands for "Picture in Picture" and allows to display mul ti ple windows containing each of them an image.
Index INDEX A Address 55 Program 55 RCU 55 Adjustment 52–54 Quick set up 52–54 Lens 52 Lens functions 53 Lens key 52 PIP 5 4 Adjustment mode 59–61 About 59 LCD display menus 60 Local keypad 59 M.
Index File services 93 Manual load fi le 93 Film mode detection 90 Front cover 181, 187 Installation 187 Removal 181 Front projection 14 G Gamma 122 General 1 1–14, 1 7 Air inlets 17 Air outlets 17.
Index Lamp mode 1 16 Overview 1 13 Powe r 1 14 Power mode 1 13 R u nt i m eo v e r v i e w 1 1 6 Status overview 1 16 Lamp door 182, 188 Installation 188 Removal 182 Lamp identi fi cation 1 15 Lamp m.
Index Network 141–144 DHCP 142 Gatewa y 1 44 Introducti on 141 IP-address 142 Subnet-mask 143 Projector address 138–139 Address 138 Common address 139 Serial communication 139–141 Baud rate setu.
Index Source timings 87 Speci fi cations 199–202 5 cable input 200 CLM R10+ 199 DVI HDCP 202 DVI input 202 HDSDI–SDI input 201 SPI 159 Diagnosis 159 Stacking 33, 35 Align projectors 35 Projectors.
Index 224 R59770021 CLM R10+ 11/10/2010.
Revision S heet To : Barco nv Events/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.1 1, Fax: +32 56.36.88.24 E-mail: service.mne@ba rco.
Een belangrijk punt na aankoop van elk apparaat Barco R9050100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Barco R9050100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Barco R9050100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Barco R9050100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Barco R9050100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Barco R9050100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Barco R9050100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Barco R9050100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
