Gebruiksaanwijzing /service van het product MBD-H8DMU+-B van de fabrikant Supermicro
Ga naar pagina of 80
H8DMU+ USER’S MANUAL Revision 1.1a S UPER.
Manual Revision 1.1a Release Date: July 22, 2009 The information in this User ’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inacc.
Preface iii Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the H8DMU+ serverboard.
H8DMU+ User ’s Manual T able of Contents Chapter 1: Introduction 1-1 Overview ......................................................................................................... 1-1 Checklist ...................................................
v T able of Contents Power Button .......................................................................................... 2-1 1 USB Ports .............................................................................................. 2-1 1 USB Headers .
H8DMU+ User ’s Manual Chapter 3: T roubleshooting 3-1 T roubleshooting Procedures ........................................................................... 3-1 Before Power On .......................................................................
Chapter 1: Introduction 1-1 Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer serverboard from an acknowledged leader in the industry . Our boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
1-2 H8DMU+ User ’s Manual Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
Chapter 1: Introduction 1-3 Figure 1-1. H8DMU+ Image.
1-4 H8DMU+ User ’s Manual Notes: 1. Jumpers not indicated are for test purposes only . 2. There are no "USB2/3" ports or headers. Figure 1-2.
Chapter 1: Introduction 1-5 H8DM U+ Quick Referenc e Jumper Description Default Setting JBT1 CMOS Clear See Section 2-7 JCF1 Compact Flash Card Master/Slave Closed (Master) JD1 Onboard Speaker Pins 6-.
1-6 H8DMU+ User ’s Manual Serverboard Features CPU • Single or dual AMD 64-bit Socket F , Opteron 2000 type processors Memory • Sixteen dual/single channel DIMM slots supporting up to 64 GB of DDR2-800 /667/533 registered ECC SDRAM Note: Memory capacities are halved for single CPU systems.
Chapter 1: Introduction 1-7 ACPI Features • Microsoft OnNow • Slow blinking LED for suspend state indicator • BIOS support for USB keyboard • Main switch override mechanism • Internal/extern.
1-8 H8DMU+ User ’s Manual Figure 1-3. nVidia MCP55 Pro Chipset: System Block Diagram Note: This is a general block diagram and may not exactly represent the features on your serverboard. See the previous pages for the actual speci fi cations of your serverboard.
Chapter 1: Introduction 1-9 1-2 Chipset Overview The H8DMU+ serverboard is based on the nVidia MCP55 Pro chipset. The nVidia MCP55 Pro functions as Media and Communications Processor (MCP). Controllers for the system memory are integrated directly into the AMD Opteron processors.
1-10 H8DMU+ User ’s Manual 1-3 PC Health Monitoring This section describes the PC health monitoring features of the H8DMU+. The serverboard has an onboard System Hardware Monitor chip that supports PC health monitoring. Onboard V oltage Monitors The onboard voltage monitor will scan these voltages continuously: CPU cores, Hyper T ransport (1.
Chapter 1: Introduction 1-1 1 1-4 Power Con fi guration Settings This section describes the features of your serverboard that deal with power and power settings. Microsoft OnNow The OnNow design initiative is a comprehensive, system-wide approach to system and device power control.
1-12 H8DMU+ User ’s Manual 1-5 Power Supply As with all computer products, a stable power source is necessary for proper and reliable operation. It is even more important for processors that have high CPU clock rates. The H8DMU+ accommodates 12V A TX power supplies.
Chapter 1: Introduction 1-13 1-6 Super I/O The disk drive adapter functions of the Super I/O chip include a fl oppy disk drive controller that is compatible with industry standard 82077/765, a data s.
1-14 H8DMU+ User ’s Manual 1-7 UIO Th e H8 D MU+ i s a sp ec iall y- d esi gne d ser ver bo ard t hat fe atur es Su per mi cr o's UI O (Un iver s al I /O ) tec hn ol ogy.
Chapter 2: Installation 2-1 Chapter 2 Installation 2-1 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic com ponents. T o prevent dam- age to your system board, it is important to handle it very carefully . The following measures are generally suf fi cient to protect your equipment from ESD.
2-2 H8DMU+ User's Manual ! 2-2 Processor and Heatsink Installation Installing the Processor (install to the CPU#1 socket fi rst) 1. Begin by removing the cover plate that protects the CPU. Lift the lever on CPU socket #1 until it points straight up.
Chapter 2: Installation 2-3 3. Align pin 1 of the CPU with pin 1 of the socket. Once aligned, carefully place the CPU into the socket. Do not drop the CPU on the socket, move the CPU horizontally or vertically or rub the CPU against the socket or against any pins of the socket, which may damage the CPU and/or the socket .
2-4 H8DMU+ User's Manual Installing the Heatsink The use of active type heatsinks (except for 1U systems) are recommended. Con- nect the heatsink fans to the appropriate fan headers on the serverboard. T o install the heatsinks, please follow the installation instructions included with your heatsink package (not included).
Chapter 2: Installation 2-5 2-3 Mounting the Serverboard into a Chassis All serverboards and motherboards have standard mounting holes to fi t different types of chassis. Make sure that the locations of all the mounting holes for both the serverboard and the chassis match.
2-6 H8DMU+ User's Manual Figure 2-2. Side and T op Views of DDR2 Installation T o Install: Insert module vertically and press down until it snaps into place. The release tabs should close - if they do not you should close them yourself. T o Remove: Use your thumbs to gently push each re- lease tab outward to release the DIMM from the slot.
Chapter 2: Installation 2-7 Notes: X indicates a pair of populated DIMM slots. If adding at least four DIMMs (with two CPUs installed), the con fi gurations with DIMMs spread over both CPUs will result in optimized performance. Note that the fi rst two DIMMs must be installed in the CPU1 memory slots.
2-8 H8DMU+ User's Manual 2-5 I/O Port and Control Panel Connections The I/O ports are color coded in conformance with the PC99 speci fi cation to make setting up your system easier . See Figure 2-3 below for the colors and locations of the various I/O ports.
Chapter 2: Installation 2-9 2-6 Connecting Cables A TX Power Connector The primary A TX power supply con- nector (JPW1) meets the SSI (Super- set A TX) 20-pin speci fi cation. Refer to the table on the right for the pin de fi nitions of the A TX power connec- tor .
2-10 H8DMU+ User's Manual NIC1 LED The NIC1 (Network Interface Control- ler) LED connection is located on pins 1 1 and 12 of JF1. Attach the NIC1 LED cable to display network activity . Refer to the table on the right for pin de fi nitions. NIC2 LED The NIC2 (Network Interface Control- ler) LED connection is located on pins 9 and 10 of JF1.
Chapter 2: Installation 2-1 1 Power Fail LED The Power Fail LED connection is located on pins 5 and 6 of JF1. Refer to the table on the right for pin de fi ni- tions.
2-12 H8DMU+ User's Manual Fan Headers The H8DMU+ has eight fan headers, which are designated F AN1 through F AN8. F AN7 and F AN8 (for active CPU heatsinks) are Pulse Width Modulated (PWM): their speed is controlled via a BIOS setting. See the table on the right for pin de fi nitions.
Chapter 2: Installation 2-13 A TX PS/2 Keyboard and PS/2 Mouse Ports The A TX PS/2 keyboard and the PS/2 mouse ports are located on the I/O backplane. The mouse is the top (green) port.
2-14 H8DMU+ User's Manual W ake-On-LAN The W ake-On-LAN header is desig- nated JWOL. See the table on the right for pin de fi nitions. Y ou must have a LAN card with a W ake-On-LAN connector and cable to use the W ake- On-LAN feature. (Note: W ake-On-LAN from S3, S4, S5 are supported by LAN1.
Chapter 2: Installation 2-15 Compact Flash Power A Compact Flash Card Power Connector is located at JWF1. For the Compact Flash Card to work properly , you will fi rst need to connect the device's power cable to JWF1 and correctly set the Compact Flash Jumper (JCF1).
2-16 H8DMU+ User's Manual 2-7 J u m p e r S et t i n g s Explanation of Jump ers T o mo dif y th e ope rati on of t he ser verboard, jumpers can be used to choose between optional se tt ings. Jum per s c reate s hor ts b et ween t wo p in s to ch an g e th e fu nc ti o n of th e c onne ct or .
Chapter 2: Installation 2-17 Note: Wh en e na bl ed , th e us er ne ed s to wr i te th ei r ow n ap pl ic at io n so f t wa re i n or- de r to di sa bl e th e Wat ch D og t im er. W atch Dog JWD controls W atch Dog, a system monitor that takes action when a soft- ware application freezes the system.
2-18 H8DMU+ User's Manual Compact Flash Master/Slave The JCF1 jumper allows you to assign either master or slave status a compact fl ash card installed in IDE1.
Chapter 2: Installation 2-19 2-8 Onboard Indicators LAN1/LAN2 LEDs The Ethernet ports (located beside the VGA port) have two LEDs. On each Gb LAN port, one LED indicates activity when blinking while the other LED may be amber or off to indicate the speed of the connection.
2-20 H8DMU+ User's Manual 2-9 Floppy , IDE and SA T A Drive Connections Use the following information to connect the fl oppy and hard disk drive cables. The fl oppy disk drive cable has seven twisted wires. A red mark on a wire typically designates the location of pin 1.
Chapter 2: Installation 2-21 IDE Connector There are no jumpers to con- fi gure the onboard IDE#1 con- nector . See the table on the right for pin de fi nitions.
2-22 H8DMU+ User's Manual 2-10 Enabling SA T A RAID Serial A T A (SA T A) Serial A T A (SA T A) is a physical storage interface that employs a single cable with a minimum of four wires to create a point-to-point connection between devices. This connection is a serial link.
Chapter 2: Installation 2-23 2. Use the arrow keys to move to Advanced > Floppy/IDE/SA T A Con fi guration > nVidia RAID Setup and press the <Enter> key . Once in the submenu, enable the "nVidia RAID Function" setting. 3. Hit the <F10> key to "Save Changes and Exit", then hit <Enter> to verify .
2-24 H8DMU+ User's Manual Figure 2-5. SA T A RAID Utility: Main Screen Figure 2-6. SA T A RAID Utility: Array List.
Chapter 2: Installation 2-25 2-1 1 Installing Drivers After all the hardware and operating system have been installed, you need to install certain drivers. The necessary drivers are all included on the Supermicro CD that came packaged with your serverboard.
2-26 H8DMU+ User's Manual Notes.
3-1 Chapter 3: T roubleshooting Chapter 3 T roubleshooting 3-1 T roubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘T echnical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter .
3-2 H8DMU+ User's Manual NOTE If you are a system integrator , V AR or OEM, a POST diagnostics card is recommended. For I/O port 80h codes, refer to App. B. Memory Errors 1. Make sure that the DIMM modules are properly and fully installed. 2. Y ou should be using registered ECC DDR-2 memory (see next page).
3-3 Chapter 3: T roubleshooting 3. If you still cannot resolve the problem, include the following information when contacting us for technical support: Serverboard model and PCB revision number .
3-4 H8DMU+ User's Manual Question: Why can't I turn off the power using the momentary power on/off switch? Answer: The instant power of f function is controlled in BIOS by the Power But- ton Mode setting. When the On/Off feature is enabled, the serverboard will have instant off capabilities as long as the BIOS has control of the system.
Chapter 4: BIOS 4-1 Chapter 4 BIOS 4-1 Introduction This chapter describes the AMIBIOS™ Setup utility for the H8DMU+. The AMI ROM BIOS is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program.
4-2 H8DMU+ User ’s Manual 4-2 Main Menu When you fi rst enter AMI BIOS Setup Utility , you will see the Main Menu screen. Y ou can always return to the Main Menu by selecting the Main tab on the top of the screen with the arrow keys.
Chapter 4: BIOS 4-3 W ait for F1 if Error This setting controls the system response when an error is detected during the boot sequence. When enabled, BIOS will stop the boot sequence when an error is detected, at which point you will need to press the F1 button to re-enter the BIOS setup menu.
4-4 H8DMU+ User ’s Manual Restore on AC Power Loss This setting allows you to choose how the system will react when power returns after an unexpected loss of power . The options are Power Of f, Power On and Last State. MPS Revision This setting allows the user to select the MPS revision level.
Chapter 4: BIOS 4-5 LBA/Large Mode LBA (Logical Block Addressing) is a method of addressing data on a disk drive. The options are Disabled and Auto . Block (Multi-Sector T ransfer) Block mode boosts IDE drive performance by increasing the amount of data transferred.
4-6 H8DMU+ User ’s Manual 32-Bit Data T ransfer Select "Enabled" to activate the function of 32-Bit data transfer . Select "Dis- abled" to deactivate the function.
Chapter 4: BIOS 4-7 S.M.A.R.T . Self-Monitoring Analysis and Reporting T echnology (SMART) can help predict impending drive failures. Select "Auto" to allow BIOS to auto detect hard disk drive support. Select "Disabled" to prevent AMI BIOS from using the S.
4-8 H8DMU+ User ’s Manual Clear NVRAM Select Y es to clear NVRAM during boot-up. The options are Y es and No . Plug & Play OS Select Y es to allow the OS to con fi gure Plug & Play devices (this is not required for system boot if your system has an OS that supports Plug & Play).
Chapter 4: BIOS 4-9 Advanced Chipset Control NorthBridge Con fi guration Memory Con fi guration Bank Interleaving Select Auto to automatically enable interleaving-memory scheme when this function is supported by the processor . The options are Auto and Disabled.
4-10 H8DMU+ User ’s Manual ECC Con fi guration ECC Mode This setting affects the DRAM scrub rate based on its setting. Options are Disabled, Basic, Good, Super , Max and User . DRAM ECC Enable DRAM ECC allows hardware to report and correct memory errors automatically .
Chapter 4: BIOS 4-1 1 DRAM Timing Mode This setting speci fi es the DRAM timing mode. Options are Auto and DCT . Alternate VID Specify the alternate VID while in low power states. Options are Auto and various voltages from .800V to 1.150V in increments of .
4-12 H8DMU+ User ’s Manual USB Mass Storage Device Con fi guration This submenu allows you to configure USB mass storage class devices. USB Mass Storage Reset Delay This setting allows you to specify the number of seconds POST waits for the USB mass storage device after the Start Unit command.
Chapter 4: BIOS 4-13 Processor & Clock Options This submenu lists CPU information and the following settings: MTRR Mapping This determines the method used for programming CPU MTRRs when 4 GB or more memory is present.
4-14 H8DMU+ User ’s Manual Serial Port2 Address This option speci fi es the base I/O port address and Interrupt Request address of serial port 2. Select "Disabled" to prevent the serial port from accessing any system resources. When this option is set to "Disabled", the serial port physi- cally becomes unavailable.
Chapter 4: BIOS 4-15 Redirection After BIOS POST Options are Disable (no redirection after BIOS POST), Boot Loader (redirection during POST and during boot loader) and Always (redirection always active). Note that some OS's may not work with this set to Always.
4-16 H8DMU+ User ’s Manual F AN1 Speed through F AN8 Reading The speeds of the onboard fans (in rpm) are displayed here. Other items in the submenu are systems monitor displays for the following inf.
Chapter 4: BIOS 4-17 Subnet Mask Use the "+" and "-" keys to select the parameter . The subnet address and current subnet address in the BMC are shown. Set PEF Con fi guration PEF Support Use this setting to Enable or Disable PEF support.
4-18 H8DMU+ User ’s Manual 4-5 Security Menu AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set fi rst. Change Supervisor Password Select this option and press <Enter> to access the sub menu, and then type in the password.
Chapter 4: BIOS 4-19 Load Optimal Defaults T o load optimal default settings, select this setting and press <Enter>. Then Se- lect "OK" to allow BIOS to automatically load the Optimal Defaults as the BIOS Settings. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications.
4-20 H8DMU+ User ’s Manual Notes.
Appendix A BIOS Error Beep Codes During the POST (Power-On Self-T est) routines, which are performed each time the system is powered on, errors may occur . Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
A-2 H8DMU+ User ’s Manual Notes.
B-1 Appendix B: BIOS POST Checkpoint Codes Appendix B BIOS POST Checkpoint Codes When AMIBIOS performs the Power On Self T est, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h.
B-2 H8DMU+ User ’s Manual Checkpoint Code Description E0h The onboard fl oppy controller if available is initialized. Next, beginning the base 512 KB memory test. E1h Initializing the interrupt vector table next. E2h Initializing the DMA and Interrupt controllers next.
B-3 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description 03h The NMI is disabled. Next, checking for a soft reset or a power on condition. 05h The BIOS stack has been built. Next, disabling cache memory . 06h Uncompressing the POST code next.
B-4 H8DMU+ User ’s Manual Checkpoint Code Description 25h Interrupt vector initialization is done. Clearing the password if the POST DIAG switch is on. 27h Any initialization before setting video mode will be done next. 28h Initialization before setting the video mode is complete.
B-5 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description 4Ch The memory below 1 MB has been cleared via a soft reset. Clearing the memory above 1 MB next. 4Dh The memory above 1 MB has been cleared via a soft reset. Saving the memory size next.
B-6 H8DMU+ User ’s Manual Checkpoint Code Description 86h The password was checked. Performing any required programming before WIN- BIOS Setup next. 87h The programming before WINBIOS Setup has completed. Uncompressing the WINBIOS Setup code and executing the AMIBIOS Setup or WINBIOS Setup utility next.
B-7 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description A9h Returned from adaptor ROM at E000h control. Performing any initialization required after the E000 option ROM had control next. Aah Initialization after E000 option ROM control has completed.
B-8 H8DMU+ User ’s Manual Notes.
Een belangrijk punt na aankoop van elk apparaat Supermicro MBD-H8DMU+-B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Supermicro MBD-H8DMU+-B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Supermicro MBD-H8DMU+-B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Supermicro MBD-H8DMU+-B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Supermicro MBD-H8DMU+-B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Supermicro MBD-H8DMU+-B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Supermicro MBD-H8DMU+-B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Supermicro MBD-H8DMU+-B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
