Gebruiksaanwijzing /service van het product D11624 van de fabrikant TANDBERG
Ga naar pagina of 19
Video on Frame Relay Tandberg D11624 rev 01.
Tandberg Video on Frame Relay D11624 rev. 01 2 Table of Contents 1. Introduction ............................................................................................................................................... 3 2. Background on transmission of video over frame relay .
Tandberg Video on Frame Relay D11624 rev. 01 3 1. Introduction This document is designed as an 'eye-opener' to video over frame relay and the idea is to show a solution that works. The equipment described in this document is the VFX-250S, a framer unit from Science Dynamics Corporation.
Tandberg Video on Frame Relay D11624 rev. 01 4 2. Background on transmission of video over frame relay The successful transmission of digitised voice over public frame relay data services the past few years has drawn attention to the question of whether video services can be transmitted over the same link.
Tandberg Video on Frame Relay D11624 rev. 01 5 3. Technical issues There are two potential technical issues, which may affect the quality of packetised, digitised video. One is delay, or more properly jitter. Jitter is the variation in delay from one frame to the next.
Tandberg Video on Frame Relay D11624 rev. 01 6 Cell based systems cut packet into fixed sizes Dropped frames are potentially a more serious problem. The frame relay standard allows the network service provider to control congestion by simply disposing of any frames which exceed the users CIR.
Tandberg Video on Frame Relay D11624 rev. 01 7 2. The second method is to establish a traffic prioritisation scheme for any channels carrying video through a FRAD (Frame Relay Access Devices) on a defined DLCI. This ensures that video frames are first out.
Tandberg Video on Frame Relay D11624 rev. 01 8 framer both at the ACT-recommended setting of 256 bytes and at 1.500 bytes (which is in line with the recommendations of other framer users) without any difference in the overall performance. You can connect either the VFX-250S or the ABL VT2C directly to a DSU/CSU on a frame relay network.
Tandberg Video on Frame Relay D11624 rev. 01 9 6. Application Overview The diagram below shows the use of the VFX-250S in a video-conferencing over frame relay application.
Tandberg Video on Frame Relay D11624 rev. 01 10 7. Technical Specification of VFX-250S 7. 1 Network & User Interface Connector: Female 37-pin D type to user equipment (Video codec) Male 37-pin D type to network equipment (FRAD) Interface: RS449 (X.
Tandberg Video on Frame Relay D11624 rev. 01 11 • 4 configuration entries, each of which contains TX and RX DLCI settings, User Clock Speed, Packet Length, and AVB • LMI type control selection &am.
Tandberg Video on Frame Relay D11624 rev. 01 12 8. Approvals FCC Class A Digital Devices and Peripherals This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Tandberg Video on Frame Relay D11624 rev. 01 13 10. Economics of Video over Frame Relay The economics of video over frame relay are similar to those driving the use of voice over frame relay. Voice over frame relay is fairly well accepted as being economical when used in international applications.
Tandberg Video on Frame Relay D11624 rev. 01 14 11. Appendix A: Cables and Pinouts 11. 1 Standard Console Cable The console port on the VFX-250S conforms to EIA-232/V.
Tandberg Video on Frame Relay D11624 rev. 01 15 11. 2 Standard EIA-449/RS449 Cables 11. 2 .1 Network Cable 11. 2 .2 User Cable A note about RTS signalling: Some manufacturers state that their network interface is RS449 (which uses RS422 signalling levels) but actually use RS423 signals for the control leads.
Tandberg Video on Frame Relay D11624 rev. 01 16 11. 3 Standard EIA-530/RS530 Cables 11. 3 .1 Network Cable 11. 3 .2 User Cable.
Tandberg Video on Frame Relay D11624 rev. 01 17 11. 4 Standard V.35 Cables 11. 4 .1 Network Cable 11. 4 .2 User Cable.
Tandberg Video on Frame Relay D11624 rev. 01 18 12. Appendix C: Glossary and abbreviations AVB - Automatic Variable Buffer. Buffering - This is a term used to describe a method where data is held in a queue to allow equalisation of speeds on either side.
Tandberg Video on Frame Relay D11624 rev. 01 19 - This is a Videoconferencing term, which is used to identify picture break-up. Digital video pictures are made up of 1000’s of pixels, each representing a colour on the image. In videoconferencing, pixels are grouped into blocks (the number of which is determined by the speed of the link).
Een belangrijk punt na aankoop van elk apparaat TANDBERG D11624 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TANDBERG D11624 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TANDBERG D11624 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TANDBERG D11624 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TANDBERG D11624 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TANDBERG D11624 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TANDBERG D11624 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TANDBERG D11624 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
