Gebruiksaanwijzing /service van het product BA140 van de fabrikant Baumatic
Ga naar pagina of 40
d wan BA140 Fully integrated washing machine.
USER MANUAL FOR YOUR BAUMATIC BA140 Fully integrated washing machine NOTE : This User Instruction Manual contains imp ortant information, including safety & installation p oints, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available fo r future reference.
3 Contents Environmental note 4 Important safety information 5 - 6 Specifications 7 Description of the appliance 8 - 11 C o n t r o l p a n e l 9 Program options 9 L C D d i s p l a y 1 0 Detergent dr.
Environmental note Note : Before discarding an old appliance, switch off and disconnect it from the power supp ly. Cut off and render any plug useless. Cut the cable off directly behind th e appliance to prevent misuse. This should be undertake n by a competent person.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the info rmation contained in this booklet, please contact the Baumatic Advice Line.
6 o Before the first use of the a ppliance, we advise that a 90°C cotton wash is completed. No garments should be placed inside the machine; however a small amount of detergent must be used. During Use o It is recommended that the a ppliance is unplugged and the water supply is switched off after the machine is used.
Specifications 9 7kg wash load 9 1400 rpm maximum spin speed 9 15 wash programs 9 LCD display 9 Delay start timer with remain time indicator 9 3 Option buttons: Easy iron E x t r a r i n s e I n t e n.
Description of the appliance 8.
Control panel Wash program selection knob This control knob allows you to select the wash program of your choice. To activate it you should press in the program selection knob, to pop out the control. Start/Stop button Once a wash program has been se lected, this button should be pressed to start the wash cycle.
LCD display 1. Wash program phases: o Prewash o Wash o Rinse o Spin and drain 2. Spin speed. 3. Program number (for a few seconds) and then program duration.
Detergent drawer Pre wash section This compartment should have deterg ent placed in it, if you are going to select a wash program that has a pre wash as part of it. Main wash section This compartment should have detergen t placed in it (you should also put a water softening agent in this section, if you use one).
Preparing the wash cycle Preparing your garments for washing o Your washing should be sorted out, according to the fabric type and the wash care symbol that is printed on the garment’s wash care label. (see separate section on wash care symbols). o Your washing should also be sorted out according to the degree of soiling.
A selection of wash care symbols o The wash care symbols should be used to help you to select the most suitable wash program. They will also help you to sort your laundry into different loads, depending on the fabric type and the highest temperature which the garment can be washed at.
Detergents and conditioners The amount of detergent that you n eed to use in your appliance, will depend on o The degree of soiling. Lightly soiled garments in general require less detergent. o The size of the wash load. A smaller wash load will require a reduction in the amount of detergent.
15 Program tables Program Fabric type Max. load of clothes (kg) Programme description 1 Normal cold Cold 7 Normal wash, rinses with conditioner (if added) and a long final spin 2 Quick 30°C Cotton/linen white/colours very light soil 1.
16 15 Draining Cotton/cotton mix synthetic/delicate wool/wool mix 7 Draining Possible option buttons Program A B C D E F Total consumption (kWh/litres) Approx. duration (minutes) 1 Normal cold Yes 0.10/54 50 2 Quick 30°C Yes No Yes Yes Yes Yes 0.20/30 30 3 Normal 30°C Yes 0.
17 Wash program guidance o A particular program option can on ly be selected if the program table advises that it is possible with the wash cycle you have selected. o The washing machine automatically selects a spin speed for a particular wash program.
Selecting a wash program 9 Load your laundry and put detergent in the relevant compartment of the soap drawer. 9 Close the porthole door firmly. 9 Activate the pop out program selector knob by depressing it. 9 Select the most appropriate wash progr for the garments that y are washing, by turning t program selector knob.
o The active phases will appear at the top of the display, as the wash program progresses. The ti me remaining until the end of the program will update throughout the wash cycle.
Delay start feature Your appliance has a delay start fe ature, which allows you to pause the start of a wash cycle until a later time. 9 Follow the process listed under “Selecting a wash program” .
9 Press the spin selection button and the spin speed will reduce in 100 rpm increments. o It is possible to reduce th e spin speed from the one automatically selected by the wash program, down to 400rpm. 9 If you continue to press the spin reduction button after 400rpm appears.
YOU MUST DO ONE OF THESE STEPS BEFORE OPENING THE DOOR OF THE APPLIANCE. OTHERWISE YOU COULD OPEN THE PORTHOLE DOOR WHILST THERE IS ST ILL WATER IN THE D RUM. You should ensure that the garments you are washing are suitable for suspending in water before selecting this opti on.
Child lock Your appliance has a child lock option, if this is set, it will mean that nobody can affect the operation of the wash program once it has started. The child lock should be activated, once a wash program is already in progress. o To activate the child lock, you sh ould hold down the START/STOP button for at least three seconds.
Maintenance and cleaning In daily use 9 Once a wash cycle has comple ted, you should pull out the detergent drawer slightly , so it can dry out. 9 Leave the porthole door ajar for a short while after a wash cycle has completed. This shou ld help to prevent stagnant smells and to protect the door seal.
25 t drawer. o Use warm water and a brush to thoroughly clean the three compartments of the detergen o Clean the area that the detergent drawer slides into with a brush. o Replace the detergent drawer by placing it back into the slot. Then push the drawer fully back into position.
Error code failure system If your appliance senses that it is not operating correctly, then an error code may appear in the LCD display. The following error codes can possibl y be remedied by the customer and the steps outlined below should be followed.
27 LL. IF AN ENGINEER A TTENDS DURING THE GUARANTEE PERIOD AND FINDS THAT A FAULT HAS BEEN CAUSED BY AN ITEM ON THE ERROR CODE LIST, WHICH COULD HAVE BEEN CLEARED BY THE CUSTOMER. THEN YOU MAY BE LIAB LE FOR THE COST OF THE SERVICE CA General troubleshooting Water under the washing machine o Tighten the drain pump filter.
Poor wash results My garments are looking gr ey and there are limescale deposits present in the drum of my washing machine. o There is not enough detergent being added. o The incorrect detergent is being used. o Stains are not being pre-treated. o The correct wash program or wash temperature was not selected.
Cleaning the drain pump filter IMPORTANT: Switch off your washing machine and disconnect the plug from your mains supply. You should clean out the filter approximately every twenty washes. If the drain pump filter is not cleaned regularly, then your appliance may find it difficult to pump out wate r efficiently.
Remove the filter and rinse out the filter under the tap. Remove any debris from the filter. Remove any debris that is in th e area of the appliance that you removed the drain pump filter from. Screw the filter clockwise back into position, making sure that it is fully tightened.
31 t reviously. 9 Locate the three transit bolts that secure the drum in position, whilst the appliance is being transported. 9 Using a screwdriver, unscrew the three plastic transit bolt covers.
Positioning and leve lling the appliance 9 Place the washing machine on a solid and level floor surface. 9 DO NOT PLACE THE WASHING MACHINE ON A CARPET. 9 Loosen the adjustable feet that are positioned on the base of the appliance. 9 Slacken off the lock nut on each of the washing machine feet using a spanner.
Connecting to the mains water supply 9 The water inlet hose will be insi de the drum of your washing machine, when you re ceive the appliance. 9 Connect and fully tighten the inlet hose to the threaded inlet valve that is located at the rear of the washing machine.
Water outlet 9 Secure the drain hose, so that it cannot move whilst the washing machine is in use. 9 Place the end of the drain hose on your drain pipe. Push it a short way down into your drain pipe. 9 IMPORTANT: Do not insert the drain ho se too deeply into the water pipe, as this may cause siphoning.
Power supply 9 IMPORTANT: As your appliance is a built in product, the electrical socket must st ill be accessible once the appliance is installed. 35 e. 9 Consult the rating plate, located on the inner rim of the porthole door of the appliance BEFORE making the electrical connections.
Before first use maintenance wash o When your washing machine has been correctly installed, we recommend that you perform a maintenance wash cycle. 36 ing process. Select the Normal 90°C wash program. etergent should be used during this maintenance wash.
U B nited Kingdom aumatic Ltd., s, Baumatic Building ad, 6 Bennet Ro Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone x ( C 0118) 933 6911 ustomer Care Fa (0118) 986 9124 Spares Telephone (01235) 4372 44 Advice Line Telephone 0118) 933 6933 ( E-mail: ales@baumatic.
38.
39.
40.
Een belangrijk punt na aankoop van elk apparaat Baumatic BA140 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Baumatic BA140 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Baumatic BA140 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Baumatic BA140 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Baumatic BA140 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Baumatic BA140 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Baumatic BA140 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Baumatic BA140 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
