Gebruiksaanwijzing /service van het product MSC1211 van de fabrikant Texas Instruments
Ga naar pagina of 35
.
IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
EVM IMPORT ANT NOTICE T exas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EV ALUA TION PURPOSES ONL Y and is not considered by TI to be fit for commercial use.
EVM W ARNINGS AND RESTRICTIONS It is important to operate this EVM within the specified input and output ranges described in the EVM User ’ s Guide. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM.
Contents iii Contents Preface About This Manual This users guide describes the function and operation of the MSC121 1EVM. This manual will help you quickly set up the evaluation module and its accom- panying software, so that you can rapidly test and evaluate the MSC121 1.
Contents iv Related Documentation From T exas Instruments Data Sheets: Literature Number: MSC121 1 SBAS267 REG1 1 17 – 5.0, – 3.3 SBVS001 ADS8325 SBAS226 MAX3243CPWR SLLS350 TPS3837L30DBVT ,TPS383.
Contents v Contents 1 Introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 MSC121 1 Description 1-2 . . . . . . . . . . .
Contents vi 1 – 1. MSC121 1EVM Block Diagram 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 – 1. RIDE (Raisonance Integrated Development Environment) 2-4 . . . . . . .
1-1 Introduction This chapter provides an overview of the MSC121 1 evaluation module and software. T opic Page 1.1 MSC121 1 Description 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MSC121 1 Description 1-2 1.1 MSC121 1 Description The MSC121 1 is a precision 24-bit delta-sigma analog-to-digital converter (ADC) with an 8051 microcontroller , and up to 32K of flash memory .
Analog Inputs 1-3 Introduction 1.3 Analog Inputs Analog input is supplied through the ten – way screw terminal block, J4. The nine inputs are connected to the MSC121 1 through a 100 Ω resistor . There is also a terminal block for AGND. The inputs have the 100 Ω resistors to provide minimal protection against overvoltage.
2-1 Getting Started This chapter guides you through unpacking the MSC121 1EVM and setting it up so you can begin working with it immediately . T opic Page 2.1 Unpacking the MSC121 1EVM 2-2 . . . . . . . . . .
Unpacking the MSC121 1EVM 2-2 2.1 Unpacking the MSC121 1EVM After unpacking the MSC121 1EVM kit, check to make sure you received all of the items listed here: - MSC121 1EVM board - 9V “ wall – wart ” power supply - 9-pin, D-sub, male-female serial cable - This user ’ s guide - Software CD-ROM 2.
Quick Start 2-3 Getting Started 2.3 Quick Start Once the MSC121 1EVM has been unpacked from its shipping container , and yo u have verified that the board is configured as shown in T able 2 – 1, it can be powered on and tested. First, c onnect t he b oard t o t he h ost P C u sing t he s upplied 9 -pin s erial c able.
Quick Start 2-4 Figure 2 – 1. RIDE (Raisonance Integrated Development Environment) Refer to the RIDE documentation and help menus for more information about ho w to interact with the RIDE environment. When a program is compiled, it can be immediately downloaded into the MSC121 1EVM by using the MSC down- load utility program.
Quick Start 2-5 Getting Started Figure 2 – 2. T ool Advanced Options UnCheck the Prompt before running box. All operands should immediately follow the switch character with no spaces except between options. i.e.: /F{NODE3}.hex /X22 /P1 /H /T If the filename, crystal frequency , or port are not included, a screen will prompt for the values.
3-1 Operation This chapter describes each function of the MSC121 1EVM, and how to use the accompanying software to program and use the MSC121 1. T opic Page 3.1 Jumpers 3-2 . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumpers 3-2 3.1 Jumpers T able 3 – 1 shows the function of each jumper on the EVM. T able 3 – 1. Jumper/Function Reference Reference Designator Setting/Pin Function Default Subsection JMP1 1 to 2 Short R1 for IDAC0 output Disconnected 3.1.1 JMP2 1 to 2 Short R2 for IDAC1 output Disconnected 3.
Jumpers 3-3 Operation 3.1.1 JMP1: Short R1 In order to allow current output IDAC0 to have full compliance, JMP1 can be used to short out resistor R1, which is in series with that signal.
Switches 3-4 3.2 Switches 3.2.1 RESET Switch Switch SW1 is a miniature pushbutton that, when pressed, forces the MSC121 1 RST line high. When released, the MSC121 1 enters a reset cycle. If communication becomes disrupted between the host and the board, or the board is unresponsive, pressing RESET will return the system to normal op- eration.
Switches 3-5 Operation 3.2.5 SW5: Emulation and Control Switch SW5 provides the means to break several signals so that they can be con- trolled by an emulator plugged into J14. This switch also provides a means of setting the operating mode of the MSC121 1.
I/O Connectors and Signals 3-6 3.3 I/O Connectors and Signals The various connectors on the MSC121 1EVM are described in this section. 3.3.1 J8: Serial0 RS-232 Connector The host PC communicates with the MSC121 1EVM through this connector , which is a D-shell type, 9-pin female, pinned out in the usual manner .
I/O Connectors and Signals 3-7 Operation 3.3.2 J9: Serial1 RS-232 Connector This connector is available for use with the second UART in the MSC121 1. Only the TD and RD lines are used. The DTR pin is connected to the DSR pin, and the RTS pin is connected to the CTS pin.
I/O Connectors and Signals 3-8 3.3.3 J6, JMP5, JMP6, B1: Power Connectors The MSC121 1EVM features a flexible power supply . Externally generated power , the onboard regulator circuitry and supplied wall-wart, or a 9V battery ca n all be used to supply power .
I/O Connectors and Signals 3-9 Operation 3.3.4 J4: Analog Inputs T erminal block J4 is the main analog input to the MSC121 1EVM, as is defined in T able 3 – 8. One terminal is provided for each of the nine MSC121 1 dif feren- tial i nputs. Each terminal is connected to the MSC121 1 through a 1k Ω resistor .
I/O Connectors and Signals 3-10 3.3.6 TP1–6: T est Points The test points can be used to monitor certain signals on the board. For information on the signals connected directly to the MSC121 1, consult the MSC121 1 datasheet (SBAS267) located at www .
Circuit Descriptions 3-1 1 Operation 3.4 Circuit Descriptions The MSC121 1EVM combines the MSC121 1 microcontroller , 128K RAM, the ADS8325, 256K EEPROM, a 22.1 184MHz crystal, support for two serial ports, and other support circuits to aid in the evaluation of the MSC121 1.
4-1 Physical Description This chapter contains the schematic drawings and PCB layouts for the MSC121 1EVM board. T opic Page 4.1 Schematics 4-2 . . . . . . . . . . . . . . . . . . . . . . . . .
Schematics 4-2 4.1 Schematics Figure 4 – 1. Processor Schematic.
Schematics 4-3 Physical Description Figure 4 – 2. Power and Analog Inputs Schematic.
Component Locations 4-4 4.2 Component Locations Figure 4 – 3. Printed Circuit Board Layout.
Power-Supply CE Certification 4-5 Physical Description 4.3 Power-Supply CE Certification.
Bill of Materials 4-6 4.4 Bill of Materials T able 4 – 1. Bill of Materials Item No. Quantity V alue Designator Description V endor Part Number 1 13 100 Ω R1 – R1 1, R32, R33 1/10W 5% chip resis.
Bill of Materials 4-7 Physical Description T able 4 – 1. Bill of Materials (continued) Item No. Part Number V endor Description Designator V alue Quantity 19 1 SP1 Piezoelectric ceramic buzzer Panasonic EFB – AA14D001 20 1 X1 22.1 184MHz quartz crystal thru-hole Citizen HC49US22.
Bill of Materials 4-8 T able 4 – 1. Bill of Materials (continued) Item No. Part Number V endor Description Designator V alue Quantity Not installed 2 J14 1 x 15 single row socket .050 ′′ spacing Mill-Max 851 – 93 – 050 – 10 – 001 (15) Not installed 1 J15 1 x 8 header, 0.
Een belangrijk punt na aankoop van elk apparaat Texas Instruments MSC1211 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Texas Instruments MSC1211 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Texas Instruments MSC1211 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Texas Instruments MSC1211 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Texas Instruments MSC1211 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Texas Instruments MSC1211 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Texas Instruments MSC1211 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Texas Instruments MSC1211 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
