Gebruiksaanwijzing /service van het product TMS320DM643X DMP van de fabrikant Texas Instruments
Ga naar pagina of 38
TMS320DM643x DMP Universal Asynchronous Receiver/Transmitter (UART) User's Guide Literature Number: SPRU997C December 2009.
2 SPRU997C – December 2009 Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated.
Preface ....................................................................................................................................... 6 1 Introduction ..........................................................................................
www.ti.com List of Figures 1 UART Block Diagram ....................................................................................................... 9 2 UART Clock Generation Diagram .................................................................
www.ti.com List of Tables 1 UART Supported Features/Characteristics by Instance ............................................................... 8 2 Baud Rate Examples for 27 MHz UART Input Clock ........................................................
Preface SPRU997C – December 2009 Read This First About This Manual This document describes the universal asynchronous receiver/transmitter (UART) peripheral in the TMS320DM643x Digital Media Processor (DMP) . Notational Conventions This document uses the following conventions.
User's Guide SPRU997C – December 2009 Universal Asynchronous Receiver/Transmitter (UART) 1 Introduction This document describes the universal asynchronous receiver/transmitter (UART) peripheral in the TMS320DM643x Digital Media Processor (DMP) .
Introduction www.ti.com Table 1 summarizes the capabilities supported on the UART. Note that the number of UARTs and their supported features vary on each device, see the device-specific data manual for more details.
8 Receiver Buf fer Register Divisor Latch (LS) Divisor Latch (MS) Baud Generator Receiver FIFO Line Status Register T ransmitter Holding Register Modem Control Register Line Control Register T ransmit.
Divisor + UART input clock frequency Desired baud rate 16 Processor generator Clock DLH:DLL UAR T input clock DSP input clock UAR T Receiver timing and control T ransmitter timing and control Baud generator BCLK Other logic Peripheral Architecture www.
BCLK Each bit lasts 16 BCLK cycles. When receiving, the UAR T samples the bit in the 8th cycle. D0 TX, RX D1 D2 P ARITY D7 D6 D5 STOP2 ST OP1 D1 D4 D2 D3 ST AR T D0 TX, RX UAR T input clock n UAR T input clock cycles, where n = divisor in DLH:DLL n BCLK www.
Peripheral Architecture www.ti.com 2.2 Signal Descriptions The UARTs utilize a minimal number of signal connections to interface with external devices. The UART signal descriptions are included in Table 3 . Note that the number of UARTs and their supported features vary on each device, see the device-specific data manual for more details.
www.ti.com Peripheral Architecture 2.4.3 Data Format The UART transmits in the following format: 1 START bit + data bits (5, 6, 7, 8) + 1 PARITY bit (optional) + STOP bit (1, 1.5, 2) It transmits 1 START bit; 5, 6, 7, or 8 data bits, depending on the data width selection; 1 PARITY bit, if parity is selected; and 1, 1.
Peripheral Architecture www.ti.com 2.6 Operation 2.6.1 Transmission The UART transmitter section includes a transmitter hold register (THR) and a transmitter shift register (TSR). When the UART is in the FIFO mode, THR is a 16-byte FIFO. Transmitter section control is a function of the UART line control register (LCR).
www.ti.com Peripheral Architecture 2.6.3 FIFO Modes The following two modes can be used for servicing the receiver and transmitter FIFOs: • FIFO interrupt mode. The FIFO is enabled and the associated interrupts are enabled. Interrupts are sent to the CPU to indicate when specific events occur.
rts Receiver FIFO D[7:0] UAR T Serial to Parallel Flow Control Transmitter FIFO Parallel to Serial Flow Control Parallel to Serial Flow Control Serial to Parallel Flow Control UAR T Transmitter FIFO Receiver FIFO D[7:0] DMP Of f-chip tx cts rx rx rts tx cts Peripheral Architecture www.
RX R TS Start Start Start Stop Stop Bits N Bits N+1 Start Stop TX CTS Start Stop Bits0−7 Start Stop Bits 0−7 Start Stop Bits 0−7 www.ti.com Peripheral Architecture 2.6.4.1 RTS Behavior RTS data flow control originates in the receiver block (see Figure 1 ).
Peripheral Architecture www.ti.com 2.7 Reset Considerations 2.7.1 Software Reset Considerations Two bits in the power and emulation management register (PWREMU_MGMT) control resetting the parts of the UART: • The UTRST bit controls resetting the transmitter only.
UAR T interrupt request to CPU IER(ETBEI) IER(ERBI) T ransmitter holding register empty Receiver data ready THREINT RDRINT Overrun error IER(ELSI) R TOINT Conditions Enable bits UART interrupt requests Arbiter Parity error Framing error Break RLSINT Receiver time-out www.
Peripheral Architecture www.ti.com 2.10 DMA Event Support In the FIFO mode, the UART generates the following two DMA events: • Receive event (URXEVT): The trigger level for the receiver FIFO (1, 4, 8, or 14 characters) is set with the RXFIFTL bit in the FIFO control register (FCR).
www.ti.com Registers 2.13 Exception Processing 2.13.1 Divisor Latch Not Programmed Since the processor reset signal has no effect on the divisor latch, the divisor latch will have an unknown value after power up.
Registers www.ti.com 3.1 Receiver Buffer Register (RBR) The receiver buffer register (RBR) is shown in Figure 9 and described in Table 7 . The UART receiver section consists of a receiver shift register (RSR) and a receiver buffer register (RBR). When the UART is in the FIFO mode, RBR is a 16-byte FIFO.
www.ti.com Registers 3.2 Transmitter Holding Register (THR) The transmitter holding register (THR) is shown in Figure 10 and described in Table 8 . The UART transmitter section consists of a transmitter hold register (THR) and a transmitter shift register (TSR).
Registers www.ti.com 3.3 Interrupt Enable Register (IER) The interrupt enable register (IER) is used to individually enable or disable each type of interrupt request that can be generated by the UART. Each interrupt request that is enabled in IER is forwarded to the CPU.
www.ti.com Registers 3.4 Interrupt Identification Register (IIR) The interrupt identification register (IIR) is a read-only register at the same address as the FIFO control register (FCR), which is a write-only register.
Registers www.ti.com Table 11. Interrupt Identification and Interrupt Clearing Information IIR Bits Priority Level 3 2 1 0 Interrupt Type Interrupt Source Event That Clears Interrupt None 0 0 0 1 None None None 1 0 1 1 0 Receiver line status Overrun error, parity error, framing For an overrun error, reading the line error, or break is detected.
www.ti.com Registers Figure 13. FIFO Control Register (FCR) 31 16 Reserved R-0 15 8 Reserved R-0 76543210 RXFIFTL Reserved DMAMODE1 (1) TXCLR RXCLR FIFOEN W-0 R-0 W-0 W1C-0 W1C-0 W-0 LEGEND: R = Read only; W = Write only; W1C = Write 1 to clear (writing 0 has no effect); - n = value after reset (1) Always write 1 to the DMAMODE1 bit.
Registers www.ti.com 3.6 Line Control Register (LCR) The line control register (LCR) is shown in Figure 14 and described in Table 13 . The system programmer controls the format of the asynchronous data communication exchange by using LCR.
www.ti.com Registers Table 13. Line Control Register (LCR) Field Descriptions (continued) Bit Field Value Description 2 STB Number of STOP bits generated. STB specifies 1, 1.5, or 2 STOP bits in each transmitted character. When STB = 1, the WLS bit determines the number of STOP bits.
Registers www.ti.com 3.7 Modem Control Register (MCR) The modem control register (MCR) is shown in Figure 15 and described in Table 16 . The modem control register provides the ability to enable/disable the autoflow functions, and enable/disable the loopback function for diagnostic purposes.
www.ti.com Registers 3.8 Line Status Register (LSR) The line status register (LSR) is shown in Figure 16 and described in Table 17 . LSR provides information to the CPU concerning the status of data transfers. LSR is intended for read operations only; do not write to this register.
Registers www.ti.com Table 17. Line Status Register (LSR) Field Descriptions (continued) Bit Field Value Description 4 BI Break indicator. The BI bit is set whenever the receive data input (RX) was held low for longer than a full-word transmission time.
www.ti.com Registers Table 17. Line Status Register (LSR) Field Descriptions (continued) Bit Field Value Description 0 DR Data-ready (DR) indicator for the receiver. If the DR bit is set and the corresponding interrupt enable bit is set (ERBI = 1 in IER), an interrupt request is generated.
Registers www.ti.com Figure 17. Divisor LSB Latch (DLL) 31 16 Reserved R-0 15 8 7 0 Reserved DLL R-0 R/W-0 LEGEND: R/W = Read/Write; R = Read only; - n = value after reset Table 18.
www.ti.com Registers 3.10 Peripheral Identification Registers (PID1 and PID2) The peripheral identification registers (PID) contain identification data (class, revision, and type) for the peripheral. PID1 is shown in Figure 19 and described in Table 20 .
Registers www.ti.com 3.11 Power and Emulation Management Register (PWREMU_MGMT) The power and emulation management register (PWREMU_MGMT) is shown in Figure 21 and described in Table 22 .
www.ti.com Appendix A Revision History Table 23 lists the changes made since the previous version of this document. Table 23. Document Revision History Reference Additions/Modifications/Deletions Section 2.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Een belangrijk punt na aankoop van elk apparaat Texas Instruments TMS320DM643X DMP (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Texas Instruments TMS320DM643X DMP heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Texas Instruments TMS320DM643X DMP vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Texas Instruments TMS320DM643X DMP leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Texas Instruments TMS320DM643X DMP krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Texas Instruments TMS320DM643X DMP bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Texas Instruments TMS320DM643X DMP kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Texas Instruments TMS320DM643X DMP . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
