Gebruiksaanwijzing /service van het product F-122CU van de fabrikant TOA Electronics
Ga naar pagina of 19
INSTRUCTION MANUAL CEILING SPEAKER SYSTEM F-122CU Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 3 3. FEA TURES ..........
3 • Leave the installation to your TOA dealer because the installation requires expert knowledge. Improper installation may cause the unit to fall, resulting in personal injury and/or property damage. • Install the unit in a location that can structurally support the weight of the unit and its mounting hardware.
4 3. FEA TURES • Bass-reflex speaker system designed to provide a wide frequency range and high power handling capability. • Wide-dispersion flush-mount ceiling speaker design employs unique acoustic construction to realize a wide area of coverage.
5 5. MOUNTING HARDW ARE INST ALLA TION Before mounting the speaker, determine the most appropriate method for the existing ceiling structure. Be sure to use an optional HY-TB1 Tile Bar Bridge in combination with the supplied ceiling reinforcement ring.
6 Ceiling panel ø 200 ± 5 mm (7 7 / 8 ± 13 / 64 ") Step 1. Cut a ø 200 mm (7 7 / 8 ") hole in the ceiling. Use the supplied paper pattern to position and trace the hole. Step 2. Install the HY-TB1 in the ceiling. Loosen the two reinforcement ring mounting screws in each tie-plate to the point that they do not fall out of their holes.
7 Step 4. Attach the ceiling reinforcement ring to each tie-plate using 2 reinforcement ring mounting screws. Ceiling reinforcement ring Reinforcement ring mounting screw Tie-plate Fit closely to the back surface of the ceiling panel.
8 Step 5. Attach a safety wire to prevent the speaker from accidentally falling. To attach, tie one end of the supplied safety wire around the speaker's safety wire hook, and tie its snap ring around the installed HY-TB1 or a solid structure.
9 6. WIRING 6.1. Using the Speaker in UL1480 Category UUMW Choke br ack et Cov er plate Cov er plate Connector cov er After completing the speaker cab le connection, turn the connector cov er in the direction indicated by the arro w , and fix the cov er with 2 screws.
10 6.2. Using the Speaker in UL1480 Category UEA Y only 6.2.1. Wiring through hard or flexible conduit Note The choke bracket equipped with the speaker has not been evaluated by UL, for conduit connection and UL514B Standard. Flexible conduit of 3/8 or 1/2 inch trade size and the UL514B conduit fitting of the same trade size can also be used.
11 6.2.2. Wiring with naked cables Loosen the screw to allo w the speak er cable to pass through. Choke br ack et Retighten the screw to fix the speaker cab le .
12 Step 2. Remove the detachable input connector from the speaker's socket, and loosen the screw of the terminal to be used. Speaker unit Detachable input connector Step 3. Insert the stripped cable end into the terminal and tighten the terminal screw with a screwdriver.
13 Caution Before mounting, check to be sure that the speaker's 3 mounting tabs are turned inside the unit as shown in the figure. If turned outward, the speaker cannot be inserted through the mounting hole. In Out Mounting tab Step 1. Insert the speaker through the mounting hole till it contacts the ceiling panel.
14 Step 3. Set the input power. Turn the input selector switch (on the unit's front) to set it to the desired input impedance. (Factory-preset to 170 Ω .) Note Setting positions "8 Ω " and "16 Ω " can be used in UL1480 Category UEAY only.
15 Mounting tab axis screw Use an electric screwdriver to detach. Mounting tab Screw cap Caution Be sure to set the screwdriver's torque for under 4 kgf · cm. Failure to do so may cause the Screw cap and the Mounting tab to fall off on the rear of ceiling panel.
16 Step 1. Clean the front grille before painting. Wipe with a soft cloth dampened in a detergent. Caution Do not use thinner or other volatile liquids to clean the grille. Step 2. Spray on a uniform, thin coat of paint. Cautions • Avoid painting with a roller or brush, as the grille mesh holes could become clogged with paint.
17 16VP Signaling Speaker 16VP Fire Protective Signaling Speaker S8460 12. SAFETY AGENCY COMPLIANCE This product is for indoor use only. The F-122CU's front-mounted rotary switch permits selection of speaker handling power (wattage) on 25 V or 70 V line operation or low impedance (8 Ω or 16 Ω ) operation.
18 13. SPECIFICA TIONS Note: The design and specifications are subject to change without notice for improvement. • Accessories Front grille ............................................................ 1 Ceiling reinforcement ring ...................
Printed in Indonesia 533-06-090-20.
Een belangrijk punt na aankoop van elk apparaat TOA Electronics F-122CU (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TOA Electronics F-122CU heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TOA Electronics F-122CU vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TOA Electronics F-122CU leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TOA Electronics F-122CU krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TOA Electronics F-122CU bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TOA Electronics F-122CU kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TOA Electronics F-122CU . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
