Gebruiksaanwijzing /service van het product F-122CU2 van de fabrikant TOA Electronics
Ga naar pagina of 16
INSTRUCTION MANUAL CEILING SPEAKER SYSTEM F-122CU2 Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 3 3. FEA TURES ..........
3 • Leave the installation to your TOA dealer because the installation requires expert knowledge. Improper installation may cause the unit to fall, resulting in personal injury and/or property damage. • Install the unit in a location that can structurally support the weight of the unit and its mounting hardware.
4 3. FEA TURES • Bass-reflex speaker system designed to provide a wide frequency range and high power handling capability. • Wide-dispersion flush-mount ceiling speaker design employs unique acoustic construction to realize a wide area of coverage.
Before mounting the speaker, check the ceiling structure is of drop ceiling with 2-foot standard ceiling tiles. 5 5. MOUNTING HARDW ARE INST ALLA TION [Installation view on Drop Ceilings] Caution Set the tile bridge so that both ends fit securely into the T-grids, even if the ceiling tile accidentally falls off.
6 Step 3. Attach a safety wire to prevent the speaker from accidentally falling. To attach, tie one end of the supplied safety wire around the speaker's safety wire hook, and tie its snap ring around a secure C-channel bar or suspension pipe.
7 6. WIRING 6.1. Using the Speaker in UL1480 Category UUMW Choke bracket Cover plate Cover plate Connector cover After completing the speaker cable connection, turn the connector cover in the direction indicated by the arrow , and fix the cover with 2 screws.
8 6.2. Using the Speaker in UL1480 Category UEA Y and CAN/CSA C22.2 No.205 Category UEA Y7 6.2.1. Wiring through hard or flexible conduit Note The choke bracket equipped with the speaker has not been evaluated by UL, for conduit connection and UL514B Standard.
9 6.2.2. Wiring with naked cables Loosen the screw to allow the speaker cable to pass through. Choke bracket Retighten the screw to fix the speaker cable.
10 Step 2. Detach the removable input connector from the speaker's socket, and loosen the screw of the terminal to be used. Speaker unit Removable input connector Step 3. Insert the stripped cable end into the terminal and tighten the terminal screw with a screwdriver.
11 Caution Before mounting, check to be sure that the speaker's 3 mounting tabs are turned inside the unit as shown in the figure. If turned outward, the speaker cannot be inserted through the mounting hole. In Out Mounting tab Step 1. Insert the speaker through the mounting hole till it contacts the ceiling panel.
12 Step 3. Set the input power. Turn the input selector switch (on the unit's front) to set it to the desired input impedance. (Factory-preset to 170 Ω .) Note Setting positions "8 Ω " and "16 Ω " can be used in UL1480 Category UEAY and CAN/CSA C22.
13 Mounting tab axis screw Use an electric screwdriver to detach. Mounting tab Screw cap Caution Be sure to set the screwdriver's torque for under 4 kgf·cm. Failure to do so may cause the Screw cap and the Mounting tab to fall off on the rear of ceiling panel.
14 10. REP AINTING THE SPEAKER Follow the procedure below when repainting the front grille: Step 1. Clean the front grille before painting. Wipe with a soft cloth dampened in a detergent. Caution Do not use thinner or other volatile liquids to clean the grille.
15 12. SAFETY AGENCY COMPLIANCE This product is for indoor use only. The F-122CU2's front-mounted rotary switch permits selection of speaker handling power (wattage) on 25 V or 70 V line operation or low impedance (8 Ω or 16 Ω ) operation. Depending on the switch settings, the unit complies with the different UL Categories as follows.
533-06-144-20 13. SPECIFICA TIONS Note: The design and specifications are subject to change without notice for improvement. • Accessories Front grille ............................................................ 1 Tile bridge .......................
Een belangrijk punt na aankoop van elk apparaat TOA Electronics F-122CU2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TOA Electronics F-122CU2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TOA Electronics F-122CU2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TOA Electronics F-122CU2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TOA Electronics F-122CU2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TOA Electronics F-122CU2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TOA Electronics F-122CU2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TOA Electronics F-122CU2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
