Gebruiksaanwijzing /service van het product RS-232C van de fabrikant TOA Electronics
Ga naar pagina of 24
9000 Series Mixer/Amplifiers RS-232C Protocol Manual V er .3.13 2007/04/05 Page 1 of 24.
T ABLE OF CONTENTS Page# 1. SUMMAR Y…………………………………………………………………….... 3 2. SERIAL PORT SETTING…………………………………………………….... 3 3. COMMAND CONFIGURA TION……………………………………………….
1. SUMMAR Y The RS-232C protocol described in this document is designed to be used to control the 9000 Series Amplifier from a PC and/or remote controller .
• If a next command received contains byte data shorter than the Data length, the previous command is abandoned. 4. TRANSMISSION DA T A AFTER COMMAND RECEPTION When normal data is received, the same data as the reception data is to be transmitted.
<Channel Attribute> 00H: Input channel 01H: Output channel <Channel Number> 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) <V alue> Position setting 00 – 7EH (- ∞ to +10 dB) See Channel Fader Gain - Position V/S Gain T able on the next page.
0DH 13 -53.0 2FH 47 -29.5 51H 81 -12.5 73H 1 15 +4.5 0EH 14 -52.0 30H 48 -29.0 52H 82 -12.0 74H 1 16 +5.0 0FH 15 -51.0 31H 49 -28.5 53H 83 -1 1.5 75H 1 17 +5.5 10H 16 -50.0 32H 50 -28.0 54H 84 -1 1.0 76H 1 18 +6.0 1 1H 17 -49.0 33H 51 -27.5 55H 85 -10.
5.1.2 Channel Fader Gain - Step Up/ Step Down Set the input and output channel gain positions by the number of steps. Positions can be varied from the current status by the designated number of steps. One position varies per step. 9000 series Amplifier informs position values changed by commands.
CHANNEL F ADER GAIN – STEP UP / STEP DOWN T ABLE Step Up Gain (dB) Step Down Gain (dB) HEX DEC HEX DEC 41H 65 +0.5 step 61H 97 -0.5 step 42H 66 +1.0 step 62H 98 -1.0 step 43H 67 +1.5 step 63H 99 -1.5 step 44H 68 +2.0 step 64H 100 -2.0 step 45H 69 +2.
received. This command is enabled when in the mixer mode only . Note: Command cannot be received during power off. 95H, 05H, <Source Channel Attribute>, <Source Channel Number>, <Destin.
CROSSPOINT GAIN T ABLE value Gain (dB) V alue Gain (dB) V alue Gain (dB) V alue Step Down HEX DEC HEX DEC HEX DEC HEX DEC 00H 0 - ∞ 22H 34 -37.0 44H 68 -3.0 65H 101 -6.0 step 01H 1 -70.0 23H 35 -36.0 45H 69 -2.0 66H 102 -7.0 step 02H 2 -69.0 24H 36 -35.
5.3. Preset Memory Recall Recalls any desired preset memories. 9000Series Amplifier responds with the same data as that received. Note: Settings to be stored in preset memories are referred to as “SCENE” in mixer mode and “EVENT” in matrix mode.
<Channel Attribute> 00H: Input channel 01H: Output channel <Channel Number> 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) <ON/OFF> 00H: Channel OFF 01H: Channel ON Example 1: Setting the Input Channel 1 to ON 92H, 03H, 00H, 00H, 01H Example 2: Setting the Input Channel 1 to OFF 92H, 03H, 00H, 00H, 00H 5.
00H: Input channel 01H: Output channel <Channel Number> 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) <Bass/T reble> 00H: Bass Gain 01H: T reble Gain <V alue> 00 -.
T ONE CONTROL GAIN POSITION T ABLE V alue Gain (dB) V alue Gain (dB) HEX DEC HEX DEC 00H 0 -12.0 0DH 13 +1.0 01H 1 -1 1.0 0EH 14 +2.0 02H 2 -10.0 0FH 15 +3.0 03H 3 -9.0 10H 16 +4.0 04H 4 -8.0 1 1H 17 +5.0 05H 5 -7.0 12H 18 +6.0 06H 6 -6.0 13H 19 +7.0 07H 7 -5.
can be valid only when EQ is set to ON. Note: Command cannot be received during power off. A1H, 07H, <Channel Attribute>, <Channel Number>, <OFF/ON>, <Band Number>, <Gain V .
06H 6 3 07H 7 5 <Freq V alue> EQ-FREQUENCY T ABLE V alue Freq (Hz) V alue Freq (Hz) HEX DEC HEX DEC 00H 0 20 1 1H 13 1k 01H 1 25 12H 14 1.25k 02H 2 31.5 13H 15 1.6k 03H 3 40 14H 16 2k 04H 4 50 15H 17 2.5k 05H 5 63 16H 18 3.15k 06H 6 80 17H 19 4k 07H 7 100 18H 20 5k 08H 8 125 19H 21 6.
<OFF/ON> 00H: Loudness OFF 01H: Loudness ON Example: Setting the loudness compensation of Output Channel 2 to ON ABH, 03H, 01H, 01H, 01H 5.9. Filter Settings Perform Filter (HPF/LPF) settings of Input / Output channels. 9000Series Amplifier responds with the same data as the receipt.
01H: Low Pass Filter <Frequency V alue> HIGH P ASS FIL TER T ABLE – 00H LOW P ASS FIL TER T ABLE – 01H Example: Setting the Input Channel 3’ s High Pass Filter to 31.5 Hz. A2H, 04H, 00H, 02H, 00H, 03H 5.10. Input Sensitivity Setting Performs input sensitivity setting of Input channel.
<V alue > INPUT SENSITIVITY T ABLE V alue Sense (dB) V alue Sense (dB) HEX DEC HEX DEC 00H 0 -10 05H 5 -42 01H 1 -18 06H 6 -48 02H 2 -24 07H 7 -54 03H 3 -30 08H 8 -60 04H 4 -36 Example: Setting the input sensitivity of Input Channel 5 to –24 dB.
F0H, 03H, 40H, 00H, 00H Response data are provided below . C0H, 09H, <Channel Attribute>, <Channel Number>, <ASCII Data (1byte)>, <ASCII Data (2byte)>, <ASCII Data (3byte)&g.
7. Speaker Preset Setting Recalls speaker EQ preset values for specific T OA model speakers. 9000Series Amplifier responds with the same data as that received .
Channel ON/OFF 92H, 03H, <Channel Attribute>, <Channel Number>, <OFF/ ON> Power ON/OFF F4H, 01H, <ON/OFF> T one control (BASS/ TREBLE) AAH, 04H, <Channel Attribute>, <.
9. COMMUNICA TION EXAMPLES Command Controller A-9000 Response Channel fader gain Input ch1 Fader gain=0dB 91H, 03H, 00H, 00H, 6AH 91H, 03H, 00H, 00H, 6AH Input ch1 Fader gain 1 step up 93H, 03H, 00H, 00H, 41H 93H, 03H, 00H, 00H, 6CH (Amplifier response of +1dB Input Channel 1 fader gain after command.
Input ch1 Insense -24dB ACH, 02H, 00H, 02H ACH, 02H, 00H, 02H Speaker preset setting Output ch2 SpPreset F-122 ADH, 02H, 01H, 01H ADH, 02H, 01H, 01H Phantom power setting Input ch3 Phantom ON 87H, 02H.
Een belangrijk punt na aankoop van elk apparaat TOA Electronics RS-232C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TOA Electronics RS-232C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TOA Electronics RS-232C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TOA Electronics RS-232C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TOA Electronics RS-232C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TOA Electronics RS-232C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TOA Electronics RS-232C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TOA Electronics RS-232C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
