Gebruiksaanwijzing /service van het product IK-TF5C van de fabrikant Toshiba
Ga naar pagina of 36
For Customer Use Enter below the Serial No . which is located on the bottom of the cabinet. Retain this inf or mation f or future ref- erence. Model No.
2 SAFETY PRECAUTIONS Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data.
3 Note the following instructions when installing. • Do not cover the product by any material. • Do not put the product on an Inflammable material such as carpet or blanket. • Do not put the product in a narrow space, since the heat generated from the product may be difficult to emanate .
4 1. CAUTIONS ON USE AND INST ALLA TION ..... 5 2. COMPONENTS ................................................ 5 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y .................................... 6 4. NAMES AND FUNCTIONS ............................
5 1. CA UTIONS ON USE AND INST ALLA TION • Carefully handle the units. Do not drop, or give a strong shock or vibration to the camera. This ma y cause problems. T reat the camera cables carefully to prevent cable prob- lems, such as cable breakdown and loosened con- nections.
6 Process Electronic shutter 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y MODE E. TRG MANU speed Syncro. scan. Partial read T rigger (1P SNR/SR) T rigger (PW SNR/SR) 1P exposure time MODE MANU MODE.
7 4. NAMES AND FUNCTIONS 1 Prism faceplate The protection cap is attached on the lens mount por tion. After removing the cap, mount the lens. Be careful not to scratch or touch the optical area. 2 DISP button Used when switching the displa y . 3 P AGE b utton Used when switching to the men u and when selecting the menus.
8 5. CONNECTION 5. 1 Standard Connection IK-TF5C DC IN 12V Lens Cable (not included) Frame grabber board, image process equipment etc. Monitor DC power supply Less than 4 mm DC IN 12V Connector used: HR10A-7P-4PB (HIROSE electronics Co. Ltd) or equivalent.
9 6. OPERA TION 1 Refer to the item " 5. CONNECTION", connect each equipment correctly . 2 T urn on the connected equipment and the power source of the camera. 3 P oint the lens at the object, operate the lens iris adjustment, focus adjustment, etc.
10 2 MANU (Manual white balance) • Set the MODE to MANU on the WHT BAL menu. (Refer to the item "7.2 (3) WHT BAL (white balance)".) • Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor etc.
11 7. MODE SETTING BY ON SCREEN DISPLA Y V ar ious settings can be controlled on the unit by using the on screen men u display ed on the monitor . The contents once set are memorized ev en if the power source is turned off , so it is unnecessar y to set again when using the unit next time.
12 7. 2 Menus • Select the menu to change the setting by referring the item "7.1 Using the Menus".) • When the [MENU UP], [MENU DOWN] buttons are pushed, the " → " on the screen moves up and down. Move the " → " to the item to change.
13 (1. 2) Changing each setting in SS (synchro. scan) mode (a) Changing the shutter speed setting 1 Set the " → " to SS by pushing [MENU UP], [MENU DO WN] buttons . 2 Select the shutter speed by pushing [D A T A UP], [DA T A DOWN] b uttons.
14 (1. 3) Changing each setting in E.TRG mode The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR. First set the " → " to MODE and select E.
15 (1. 3. 2) Changing each setting in 1P SR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either , by pushing [D A T A UP], [DA T A DOWN] buttons .
16 (1. 3. 3) Changing each setting in PW SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either , by pushing [D A T A UP], [DA T A DOWN] b uttons.
17 (1. 3. 4) Changing each setting in PW SR mode -- SHUTTER -- MODE E.TRG E.TRG PW SR TRG.P PART OFF <MODE = E.TRG E.TRG = PW SR> • Partial scanning switch OFF/120fps/180fps/E.
18 (1. 3. 5) Changing each setting in RR mode (a) Changing the partial scanning setting 1 Set the " → " to P ART by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either OFF/120fps/180fps/E.120fps/E.180fps by pushing [D A T A UP], [DA T A DOWN] b uttons.
19 ( 3 ) WHT BAL (White balance) WHT BAL has two modes; A WB, MANU . Set the " → " to MODE, push the [D A T A UP], [DA T A DOWN], and select mode among A WB, MANU. (3. 1) Changing each setting in AWB (Automatic White Balance) mode (a) Changing color temperature setting 1 Set the " → " to C.
20 ( 4 ) PROCESS (4. 1) Changing master pedestal 1 Set the " → " to M. PED by pushing [MENU UP], [MENU DO WN] buttons. 2 Set the master pedestal by pushing [D A T A UP], [DA T A DOWN] b uttons. (4. 2) Changing R pedestal 1 Set the " → " to R.
21 ( 5 ) SYNC When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync) automatically . (5. 1) Adjusting horizontal phase 1 Set the " → " to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.
22 7. 3 External Sync When using the unit with an e xter nal sync signal, input HD and VD to CC3 and CC4 of the DIGIT AL ter minal. When the external sync signal is input, the camera automatically switches its sync from the internal sync to the external sync.
23 ( 3 ) Using the unit with external sync signal When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horiz ontal phase".
24 7. 5 EXT TRIG (External trigger) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, and 1 frame images are output.
25 About 1 µ s Exposure period* 2 Exposure period* 2 Tr igger* 1 Negative polarity mode Po sitive polarity mode RGB data (video interval image) (Internal VD) * 3 FV AL LV AL, DVA L 20H ( Pa r tial scanning OFF ) 18H ( Pa r tial scanning 120fps) 23H ( Pa r tial scanning 180fps) (1.
26 ( 2 ) 1P SR (1 Pulse T rigger Sync Reset) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, the ver tical sync signal is reset and frame images are output. (2. 1) 1 Pulse T rigger SYNC-RESET Picture Output Timing *1: Exter nally input signal *2: Exposure time is determined by the setting of "7.
27 ( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET) The trigger input to CC1 of the DIGIT AL ter minal dev elops 1 frame images. (3. 1) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (At T.
28 (3. 2) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (at Time of Internal Sync) *1: Exter nally input signal *2: Exposure time = T r igger pulse width + 6 µ s (V alid tr igger pulse width is 2 µ s or greater f or external trigger shutter operation.
29 ( 4 ) PW SR (Pulse width trigger SYNC-RESET) The trigger input to the CC1 of the DIGIT AL ter minal dev elops 1 frame images. (4. 1) 1 Pulse Width T rigger SYNC-RESET Picture Output Timing *1: Exte.
30 ( 5 ) RR (Reset restart) Input of an external reset-restart signal (CC4 of the DIGIT AL terminal: External VD input) permits one screen of information to be output at an arbitrary timing.
31 7. 6 Partial Read ( 1 ) Partial Scanning OFF (All pixels scanning) In this mode, all pix els independent signal from the DIGIT AL connector is output each 1/60 second (Line order output). ( 2 ) Partial Scanning ON In this mode, the pix el signal of the vertical center por tion from the DIGIT AL connector is output.
32 8. INPUT OUTPUT SIGNAL SPECIFICA TOINS ( 1 ) HD Input Specifications The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD falling edge) as illustrated in the above diagram. External VD falling edge: Please input within about 100 clock cycles of the standard center phase .
33 9. CCD OUTPUT W A VEFORM TIMING CHAR T ( 1 ) Horizontal Output W aveform Timing Chart 132 clk 31 clk 72 clk 16 clk 2 clk 7 clk 40.7 ns LV AL, DVA L CCD output signal Pixel Clock 4 clk Optical blac .
34 10. SPECIFICA TIONS P ower supply Power consumption Pick-up system Image sensor (Effectiv e pixels) Scanning system Scan frequency Sync system Horizontal resolution Sensitivity Minimum illumination.
35 12. BEFORE MAKING A SER VICE CALL 1 1. EXTERNAL APPEARANCE DIAGRAM DISP PAGE DC IN 12V MENU DATA (AWB) 44 [1.73] 44 [1.73] 22 [0.87] 5 [0.20] 26 [1.02] 6.3 [0.25] 78 [3.07] 56 [2.20] 5 [0.20] 26 [1.02] 25 [0.98] 25 [0.98] 25 [0.98] 12 [0.47] 34 [1.
LIMITED W ARRANTY TOSHIBA CCD CAMERA Promptly register your product with T oshiba on-line at www.toshiba.com/taisisd. By registering y our product you will be eligib le for periodic updates, announcements , and special offers.
Een belangrijk punt na aankoop van elk apparaat Toshiba IK-TF5C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Toshiba IK-TF5C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Toshiba IK-TF5C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Toshiba IK-TF5C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Toshiba IK-TF5C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Toshiba IK-TF5C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Toshiba IK-TF5C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Toshiba IK-TF5C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
