Gebruiksaanwijzing /service van het product R940 van de fabrikant Toshiba
Ga naar pagina of 205
User's Manual TECRA R950/R940 PORTÉGÉ R930 Satellite Pro R950/R940 Satellite R950/R945/R940/R930 Series.
Table of Contents Preface General Precautions Chapter 1 Getting Started Equipment checklist ............................................................................. 1-1 Getting Started .............................................................
Computer Handling ............................................................................. 3-54 Heat dispersal ...................................................................................... 3-56 Chapter 4 Utilities & Advanced Usage Utilities and Applications .
Copyright © 2012 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Wi-Fi is a registered trademark of the Wi-Fi Alliance. Secure Digital and SD are trademarks of SD Card Association. Memory Stick, Memory Stick Duo, Memory Stick PRO, Memory Stick PRO Duo and Memory Stick Micro are trademarks or registered trademarks of Sony Corporation.
and microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment. FCC conditions This device complies with part 15 of the FCC Rules.
those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards. To avoid general EMC problems, the following guidance should be noted: Onl.
Video Standard Notice THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING VIDEO IN COMPLI.
Following information is only valid for EU-member States: Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product.
These symbols may not stick depending on the country and region where you purchased. Disposing of the computer and the computer's batteries Discard this computer in accordance with applicable laws and regulations. For further information, contact your local government.
ENERGY STAR ® Program Your Computer model may be ENERGY STAR ® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies.
1. Panasonic Precision Devices Co., Ltd. DVD SuperMulti with Double Layer Blu-ray™ Writer drive Panasonic Precision Devices Co., Ltd. 1080 T akano Nagomi-machi Tamana-Gun Kumamoto, Japan SERIAL NO. 2. TOSHIBA SAMSUNG STORAGE TECHNOLOGY DVD SuperMulti with Double Layer TOSHIBA SAMSUNG STORAGE TECHNOLOGY KOREA CORPORATION 14F, Bldg.
Preface Congratulations on your purchase of this computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your computer.
Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
Stress injury Carefully read the Instruction Manual for Safety and Comfort . It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture and lighting that can help reduce physical stress.
Chapter 1 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA.
TOSHIBA eco Utility TOSHIBA Bulletin Board TOSHIBA ReelTime TOSHIBA HW Setup Utility TOSHIBA Web Camera Application TOSHIBA Face Recognition TOSHIBA HDD Protection TOSHIBA Service Station TOSHIBA PC H.
Before you install a device or application, save any data in memory to the hard disk drive or other storage media. Failure to do so may result in the loss of data. Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power.
Never place your computer or AC adaptor on a wooden surface, furniture, or any other surface that could be marred by exposure to heat since the computer base and AC adaptor's surface increase in temperature during normal use. Always place your computer or AC adaptor on a flat and hard surface that is resistant to heat damage.
3. Plug the power cord into a live wall outlet - the Battery and DC IN indicators on the front of the computer should glow. Opening the display The display panel can be opened to a wide range of angles for optimal viewing.
Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 5, Power and Power-Up Modes for more information.
Starting up for the first time The Windows 7 Startup Screen will be the first screen displayed when you turn on the power. Follow the on-screen instructions on each screen in order to properly install the operating system. When it is displayed, be sure to read the Software License Terms carefully.
When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer. This includes turning off any wireless communication functionalities, and cancelling settings that reactivate the computer automatically, such as a timer recording function.
Allows the use of the panel power off feature. Executing Sleep Mode You can also enable Sleep Mode by pressing FN + F3 - please refer to the Hot key functions section in Chapter 3, Operating Basics, for further details. You can enter Sleep Mode in one of three ways: Click Start , point to the arrow icon ( ) and then select Sleep from the menu.
Do not install or remove a memory module while the computer is in Hibernation Mode. Data will be lost. Do not switch to Hibernation Mode while transferring data to external media, such as USB devices, memory media or other external memory devices. Data will be lost.
After you turn off the computer, and the content of memory has been saved to the hard disk drive, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix C.
Figure 2-1 Front of the computer with display panel closed (R950) 1 3 2 4 5 6 7 1. DC IN indicator 5. Memory media slot indicator 2. Power indicator 6.
Wireless communication indicator The Wireless communication indicator glows orange when the Wireless functions are turned on. Some models are equipped with Wireless functions. Wireless WAN/WiMAX indicator The Wireless WAN/WiMAX indicator glows blue when the Wireless WAN/WiMAX functions are turned on.
Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. External RGB monitor port This port provides 15-pin, analog RGB port.
Smart Card slot This slot allows you to install a Smart Card device. Some models are equipped with a Smart Card slot. Right side (R950) The following figure shows the computer’s right side. Figure 2-3 The right side of the computer (R950) 6 7 5 4 1 2 3 1.
eSATA/USB combo port One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on the right side of the computer. This port with the icon ( ) supports the following functions: USB Sleep and Charge function System ON CDP Charge Mode Optical disc drive The computer may be configured with an optical disc drive.
Back (R950) The following figure shows the computer’s back. Figure 2-4 The back of the computer (R950) 1 1. Battery pack Battery pack The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected.
Battery lock Slide the battery lock to release the battery pack ready for removal. Battery release latch Slide and hold this latch into its "Unlock" position in order to release the battery pack for removal. For more detailed information on removing the battery pack please refer to Chapter 5, Power and Power-Up Modes .
Figure 2-6 The front of the computer with the display panel open (R950) 2 6 11 12 12 9 3 5 1 6 14 16 7 8 18 13 10 15 17 4 1. Display screen 10. Touch Pad ON/OFF button 2. Web Camera* 11. Fingerprint Sensor* 3. Web Camera LED* 12. Touch Pad control buttons 4.
Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger .
TOSHIBA Presentation button The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center. AccuPoint A pointer control device located in the center of the keyboard is used to control the on-screen pointer.
LCD Sensor switch This switch senses when the display panel is either closed or opened and activates the Panel Power Off/On feature as appropriate. For example, when you close the display panel the co.
Power indicator The Power indicator normally glows green when the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash orange - approximately two seconds on, two seconds off.
Figure 2-8 The left side of the computer (R940) 7 8 6 5 4 1 2 3 1. DC IN 19V jack 5. eSATA/USB combo port 2. Cooling vents 6. Universal Serial Bus (USB 3.0) port 3. External RGB monitor port 7. Microphone jack 4. HDMI out port or DisplayPort* 8. Headphone jack * Provided with some models.
eSATA/USB combo port One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on the left side of the computer. This port has eSATA (External Serial ATA) function. This port with the icon ( ) supports the following functions: USB Sleep and Charge function System ON CDP Charge Mode Universal Serial Bus (USB 3.
Smart Card slot This slot allows you to install a Smart Card device. Some models are equipped with a Smart Card slot. Optical disc drive The computer may be configured with an optical disc drive. 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.
Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer. Please note that it is not possible to confirm the operation of all functions of all USB devices that are available.
Figure 2-11 The underside of the computer (R940) 1 5 2 4 6 3 1. Battery lock 4. Battery release latch 2. Docking port* 5. Memory module slot 3. Battery Pack 6. Cooling vents * Provided with some models. Product appearance depends on the model you purchased.
Memory module slot The memory module slot allows the installation, replacement and removal of additional memory module. The size of the memory modules varies depending on the model. The actual amount of useable system memory may be less than the installed memory modules.
Figure 2-12 The front of the computer with the display panel open (R940) 3 4 8 12 17 16 16 14 13 2 1 8 9 10 7 6 4 5 7 11 15 18 1. Display screen 10. Keyboard 2. Microphone* 11. TOSHIBA Presentation button 3. Web Camera LED* 12. TOSHIBA eco button 4. Web Camera* 13.
Microphone A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 3, Operating Basics for more information. Web Camera LED The Web Camera LED glows when the Web Camera is operating.
LCD Sensor switch This switch senses when the display panel is either closed or opened and activates the Panel Power Off/On feature as appropriate. For example, when you close the display panel the co.
AccuPoint A pointer control device located in the center of the keyboard is used to control the on-screen pointer. Refer to the Using the AccuPoint section in Chapter 3, Operating Basics. Some models are equipped with an AccuPoint. Touch Pad ON/OFF button Pressing the Touch Pad ON/OFF button enables or disables the Touch Pad function.
DC IN indicator The DC IN indicator normally glows green when power is being correctly supplied from the AC power adaptor. However, if the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will flash orange.
Left side (R930) The following figure shows the computer’s left side. Figure 2-14 The left side of the computer (R930) 1 2 3 4 6 5 1. DC IN 19V jack 4. eSATA/USB combo port 2. Cooling vents 5. Universal Serial Bus (USB 3.0) port 3. External RGB monitor port 6.
Universal Serial Bus (USB 3.0) port One Universal Serial Bus port, which complies to the USB 3.0 standard, is provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. HDMI out port HDMI out port can connect with Type A connector HDMI cable.
Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. The integrated sound system provides support for the computer's internal speakers and microphone, as well as allowing an external microphone and headphones to be connected via the appropriate jacks.
Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly. USB 3.0 port(s) may work as USB 2.
Figure 2-17 The underside of the computer (R930) 1 2 4 3 5 6 1. Battery lock 4. Battery release latch 2. Docking port* 5. Memory module slot 3. Battery Pack 6. Cooling vents * Provided with some models. Product appearance depends on the model you purchased.
Memory module slot The memory module slot allows the installation, replacement and removal of additional memory module. The size of the memory modules varies depending on the model. The actual amount of useable system memory may be less than the installed memory modules.
Figure 2-18 The front of the computer with the display panel open (R930) 13 11 12 12 10 2 1 17 16 15 3 6 5 7 8 4 14 18 9 1. Display screen 10. Touch Pad ON/OFF button 2. Web Camera* 11. Fingerprint Sensor* 3. Web Camera LED* 12. Touch Pad control buttons 4.
Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger . TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
Microphone A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 3, Operating Basics for more information. Touch Pad ON/OFF button Pressing the Touch Pad ON/OFF button enables or disables the Touch Pad function.
Do not put any magnetic objects close to this switch as they may cause the computer to automatically enter Hibernation Mode and shut down even if the Panel Power Off feature is disabled. Internal Hardware Components This section describes the internal hardware components of your computer.
RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. Video RAM The memory in a computer's graphics adaptor, used to store the image displayed on a bitmap display. The amount of Video RAM available is dependent on the computer's system memory.
Intel ® Display Power Saving Technology (R950 & R940) Intel GPU model may include the Display Power Saving Technology feature that can save the computer's power consumption by optimizing picture contrast on the internal LCD.
Right-click on the desktop and click Graphics Properties... In this control panel: 1. Click Power . 2. Select On battery from the drop-down menu in Power Source .
You can use BIOS Setup to enable/disable the function and change the specified time setting from Sleep Mode to Hibernation Mode. 1. Press and hold the F2 key, and then turn on the computer - the BIOS setup utility will load. 2. Select Advanced . 3. Enable/Disable Intel(R) Rapid Start Technology function.
Chapter 3 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. TOSHIBA Dual Pointing Device Some models are equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.
Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad. Refer to the Using the Touch Pad section for details. Some models are equipped with an AccuPoint. AccuPoint precautions Certain conditions can affect the on-screen pointer when using AccuPoint.
The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages. In use there are six different types of keys, specifically typewriter keys, function keys, soft keys, Hot keys, Windows special keys and the keypad overlay.
Soft keys: FN key combinations The FN (function) is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
3. Click the desired option. To use a Hot Key Card using a hot key: 1. Press and hold the FN key. 2. Press the hot key associated with the desired function. The associated hot key card appears at the top of the screen with its available options below it.
Touch Pad Pressing FN + F9 enables or disables the Touch Pad function. Zoom (Display resolution) Pressing FN + Space changes the display resolution. ODD Pressing FN + TAB ejects the disc tray. Reduce Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows.
Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow Mode To turn on Arrow Mode, press FN + F10 - the Arrow Mode indicator lights and you are able to access cursor and page control functions by using the keys.
2. Using the overlay keys, type the ASCII code of the character you require. 3. Release ALT or ALT + FN - the ASCII character will appear on the display screen. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping.
Enroll two or more fingers. Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers. Check the condition of your finger - any conditions which have changed .
In use, the fingerprint authentication system will use the same username and password as defined within the Windows operating system. If no Windows password has been configured, you must do this before starting the fingerprint registration process. This sensor has the memory space for at least twenty fingerprint patterns.
3. The TOSHIBA Fingerprint Utility main menu is displayed. Select Enroll in the main menu. 4. In the Enroll window, it enables you to delete the fingerprint data for the currently logged in user.
Fingerprint Pre-Boot Authentication and Single Sign- on feature Overview about Fingerprint Pre-Boot Authentication The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up.
Single Sign-On feature. You should check that your fingerprint is enrolled before configuring the settings. 1. Logon as Administrator (means a user has administrator privileges). 2. Click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Fingerprint Utility .
Using optical disc drives The full-size drive provides high-performance execution of disc based programs. You can run either 12 cm (4.72") or 8 cm (3.
3. Lay the disc, label side up, in the disc tray. Figure 3-6 Inserting a disc (R940) 1 1. Laser lens When the disc tray is fully opened, the edge of the computer will slightly cover the disc tray. Therefore, you will need to turn the disc at an angle when you place it in the disc tray.
When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. 2. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc. 3. Push the center of the disc tray to close it.
Blu-ray™ discs BD-R, BD-R DL discs can be written only once. The recorded data cannot be erased or changed. BD-RE, BD-RE DL discs can be recorded more than once. Writing discs The TOSHIBA Disc Creator and Corel Digital Studio are provided as writing softwares with this computer.
problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.
DVD-RAM: (DVD Super Multi drive only) DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Corporation (for 3x and 5x speed media) Hitachi Maxell, Ltd.
Make sure that the writing/rewriting operation is completed before going into either Sleep Mode or Hibernation Mode (You can remove an optical media on the optical disc drive after writing is completed). If the media is of poor quality, or is dirty or damaged, writing or rewriting errors may occur.
TOSHIBA Disc Creator does not support recording to DVD-RAM discs - to achieve this you should use Windows Explorer or another similar utility. When you back up a DVD disc, be sure that the source driv.
7. Input project name and select a style. 8. Click the Go to menu editing button. 9. Click the Burn button. How to learn more about Corel Digital Studio Please refer to the Help and Manual files for additional Corel Digital Studio information. Opening the Corel Digital Studio Manual Press F1 key when Corel Digital Studio is launched.
Do not perform any of the following actions: Operate the computer for any other function, including using a mouse or Touch Pad, or closing/opening the display panel. Bump or cause vibration to the computer. Use the Mode control button and Audio/Video control button to reproduce music or voice.
Do not playback video while watching or recording television programs using other applications. Doing so may cause DVD-Video playback or television program recording errors. In addition, if prescheduled recording starts during DVD-Video playback it may cause DVD-Video playback or television program recording errors.
If the DVD-Video image is not displayed on an external display or television, stop the TOSHIBA VIDEO PLAYER, and change the screen resolution. To change the screen resolution, click Start -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution .
Notes on Use This software can only be used on Windows 7. Playback of high bit rate content may cause frame dropping, audio skipping or decrease in computer performance. Close all other applications before playing back Blu-ray Disc™. Do not open any other applications or carry out any other operations during Blu-ray Disc™ playback.
The Blu-ray Disc™ movie can be played only on internal LCD displays or external devices connected via an HDMI output. In Clone mode (Dual View), TOSHIBA Blu-ray Disc Player may not function properly. This product does not play HD DVD discs. Blu-ray™ discs with high definition content are required for HD viewing.
Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.
Setting 1. Please make sure that the Wireless Communication function is on. 2. Click Start -> Control Panel -> Network and Internet -> Network and Sharing Center . 3. Click Set up a new connection or network . 4. Follow the wizard. You will need the name of the wireless network together with security settings.
The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
This Bluetooth Stack is based on the Bluetooth specification, depending on the model you purchased. However, TOSHIBA cannot confirm the compatibility between any computing products and/or other electronic devices that use Bluetooth, other than TOSHIBA notebook computers.
malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T), be sure to connect with a CAT5e cable or higher. You cannot use a CAT3 or CAT5 cable.
Optional devices Optional devices can expand the computer's capabilities and its versatility. This section describes the connection or installation of the following devices: Cards/memory ExpressC.
4. Press the ExpressCard gently to ensure a firm connection is made. Figure 3-9 Inserting the ExpressCard (R940) 2 1 1. ExpressCard slot 2. ExpressCard 5. After inserting the ExpressCard you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct.
Inserting a Smart Card The Smart Card slot is located on the side of the computer. The Windows hot-install feature allows you to insert a Smart Card while the computer is turned on. To install a Smart Card, follow the steps as detailed below: 1. Insert the Smart Card into the Smart Card slot with the metal connectors facing up.
Keep foreign objects out of the memory media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or Keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
The SD memory card logo is ( ). The SDHC memory card logo is ( ). The SDXC memory card logo is ( TM ). The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 32GB. The maximum capacity of SDXC memory cards is 64GB.
Set the write-protect switch to the lock position, if you do not want to record data. Memory cards have a limited lifespan, so it is important to backup important data. Do not write to a card if the battery power is low. Low power could affect writing accuracy.
When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data. Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied - doing so may cause data to be lost.
Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. a. The computer is turned on. b. The computer was shut down in either Sleep or Hibernation Mode. c. Wake-up on LAN is enabled.
6. Slide your fingernail or a thin object under the cover and lift it off. Figure 3-12 Removing the memory module cover (R940) 2 1 1. Screw 2. Memory module cover User's Manual 3-42.
7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. Figure 3-13 Seating the memory module (R940) 3 2 1 1.
8. Seat the memory module cover in place and secure it with the screw(s). Take care to ensure that the memory module cover is firmly closed. Figure 3-14 Seating the memory module cover (R940) 2 1 1.
8. Grasp the module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.
Figure 3-16 Connecting the monitor cable to the External RGB monitor port (R940) 1 2 1. External RGB monitor port 2. Monitor cable There are no fastening screws for an external monitor cable on this computer's External RGB monitor port. However, external monitor cables which have connectors with fastening screws can still be used.
Connecting the HDMI out port 1. Plug one end of the HDMI cable into the HDMI in port of the HDMI device. 2. Plug the other end of the HDMI cable into the HDMI out port on your computer. Figure 3-17 Connecting the HDMI out port (R940) 1 2 1. HDMI out port 2.
Be sure to use the FN + F5 HotKey to select the display device before starting to play video. Do not change the display device while playing video. Do not change the display device under the following conditions. While data is being read or written. While communication is being carried out.
When you change the display output device by hot key like FN + F5 , the playback device may not switch automatically. In this case, in order to set the playback device to the same device as the display output device, please adjust the playback device manually by the following steps: 1.
If you connect an eSATA device after the computer has already been turned on, it will take about ten seconds for it to be recognized by the computer. Do not attempt to disconnect and reconnect the drive before this period has elapsed.
TOSHIBA Docking Station Utility Models with a docking port support system sleep undocking operation. You can enable/disable the system sleep undocking operation. If enabled, the computer goes into Sleep Mode when you undock the computer. You can undock the computer in one of the following ways: Press the Eject button on the port replicator.
Figure 3-19 Security lock (R940) 1 2 1. Security lock slot 2. Security lock Optional TOSHIBA Accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use.
To adjust the volume level of speakers or headphones, move the Speakers slider. To adjust the volume level of an application that you are using, move the slider for the corresponding application. Microphone Level Follow the steps below to change the microphone recording level.
Information Click the Information button to view hardware information, software information, and language setting. Power Management The audio controller in your computer can be turned off when the audio function is not used. To adjust the configuration of audio power management, click the Power Management button .
Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely - in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage.
Heat dispersal To protect against overheating, the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer's internal temperature rises to a certain level.
Chapter 4 Utilities & Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them.
TOSHIBA Peak Shift Control TOSHIBA Peak Shift Control is a function that can help reduce power usage during periods of peak demand by shifting some power consumption to periods when demand is lower.
Fingerprint Utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints which can then be linked to a username and password in order to remove the need to input these details from the keyboard.
Bluetooth Stack for Windows by Toshiba This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones. Bluetooth functions cannot be used in models that do not have a Bluetooth module installed.
TOSHIBA DVD-RAM Utility This utility has the function of Physical Format and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator. To start this utility, click Start -> All Programs -> TOSHIBA -> Media & Entertainment -> DVD-RAM Utility .
TOSHIBA Bulletin Board Bulletin Board is a convenient place to pin things to visually organize in a fun and creative way. Simply drag and drop your favorite pictures, files or notes to pin them on the Board. You can use it to create thumbnail shortcuts, reminders, to-do list and so on according to your personal style.
TOSHIBA Speech System The TOSHIBA Speech System consists of a voice-composition application (text-to-speech) that analyzes documents and reads them aloud, and a speech-recognition application that recognizes the words you speak into a microphone.
You may not have all the softwares listed above depending on the model you purchased. Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use. Access each function using the following procedures.
Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Instant security A specific hot key function automatically locks the system providing data security.
Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software. The contents of main memory are automatically saved to the hard disk drive so that when you next turn the power on again, you can continue working right where you left off.
You can use the Sleep and Charge function to charge certain USB- compatible external devices such as mobile phones or portable digital music players. However, the Sleep and Charge function may not work with certain external devices even if they are compliant with the USB specification.
Enabling Sleep and Charge This utility can be used to enable and disable the Sleep and Charge function. Select the Enable Sleep and Charge check box to enable this function for the compatible USB ports.
TOSHIBA Face Recognition does not guarantee the correct identification of a user. Changes to the likeness of a registrant, such as hair style changes, wearing a cap, or wearing glasses may effect the recognition rates when such changes occur after the registrant had registered.
The Management screen is displayed for a logged-in user whose face has already been registered. 2. Click Run as administrator in lower left of the Management screen, and then click the Register button. The Registration screen is displayed. If you wish to practice, click on the Next button in the Registration screen.
2. Select a user which is displayed in the Management screen. 3. Click the Delete button. "You are about to delete the user data. Would you like to continue?" will be displayed on the screen. If you do not want the data to be deleted, click the No button and you will then be returned to the Management screen.
7. Verification will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another. If an error occurs during authentication, you will be returned to the Select Tiles screen. 8. The Windows Welcome screen will be displayed, and will be logged in automatically to Windows.
Delete (button) Click this button to delete a registered password. Before you can delete a password, you must first enter the current password correctly.
Starting the computer by password If you have already registered a password, there are several ways to start the computer: Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint System Pre-Boot Authentication.
Accessing HW Setup To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> HWSetup . HW Setup window The HW Setup window contains a number of tabs (General, Display, CPU, Boot Setting, Keyboard, LAN, SATA, USB and Advanced) to allow specific functions of the computer to be configured.
CPU This function allows you to set the processor's operating mode. Dynamic CPU Frequency Mode This option allows you to configure the power saving modes associated with the processor - the follo.
1. Hold down F12 and boot the computer. when the TOSHIBA Leading Innovation >>> screen appears, release the F12 key. 2. Use the up and down cursor keys to select the boot device you want and press ENTER . If a Supervisor Password has been set, manual boot device selection functions may be restricted.
this option will only work with the internal keyboard and only when the computer is in Sleep Mode. Enabled Enables the Wake-up on Keyboard function. Disabled Disables the Wake-up on Keyboard function.
USB Legacy USB Support Use this option to enable or disable USB Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the Legacy USB Support item to enabled. Enabled Enables the USB Legacy Emulation.
SATA This feature allows you to set conditions for SATA. eSATA This feature allows you to enable/disable the eSATA port. Enabled Enables the eSATA port (Default). Disabled Disables the eSATA port in order to save power. SATA Interface setting This feature allows you to set SATA interface setting.
may also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA's authorized service providers. Additionally, TOSHIBA may also use this information for quality assurance analysis.
Using an acceleration sensor built into the computer, TOSHIBA HDD Protection detects vibration shocks and similar signs of movement of the computer, and automatically moves the Hard Disk Drive head to a safe position to reduce the risk of damage that could be caused by head-to-disk contact.
could result in frequent execution of TOSHIBA HDD Protection, which will slow Hard Disk Drive reading and writing. Set a lower detection level when the speed of Hard Disk Drive reading and writing is a priority.
This function does not work when the computer is booting, in Sleep Mode, in Hibernation Mode, in transition to Hibernation Mode, recovering from Hibernation Mode, or powered off. Do not subject the computer to vibration or impact while the function is disabled.
Be sure to close all other software programs except the Recovery Media Creator. Do not run software such as screen savers which can put a heavy load on the CPU. Operate the computer at full power. Do not use power-saving features. Do not write to the media when the virus check software is running.
Restoring the pre-installed software from your created Recovery Media If the pre-installed files are damaged, you are able to either use the Recovery Media you have created or the hard disk drive recovery process to restore the computer to the state it was in when you originally received it.
Restoring the pre-installed software from the Recovery hard disk drive A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem.
DisplayPort Model With TOSHIBA Hi-Speed Port Replicator II: Computer LCD Yes Yes Yes - - RGB - - - - - DisplayPort Yes Yes Yes Yes Yes Replicator RGB Yes - - Yes Yes HDMI - Yes - Yes - DisplayPort - -.
Chapter 5 Power and Power-Up Modes The computer's power resources include the AC adaptor, battery pack and any internal batteries. This chapter provides details on making the most effective use o.
Power on Power off (no operation) AC adaptor not connected Remaining battery capacity is above low battery trigger point • Operates • LED: Battery off DC IN off Remaining battery capacity is below.
If the battery pack becomes too hot while it is being charged, the charge will stop and the Battery indicator will go out. When the battery pack's temperature falls to a normal range, charging will resume - this process will occur regardless of whether the computer's power is on or off.
use of the computer away from an AC power source although you should not change the battery pack while the AC adaptor is connected. Before you remove the battery pack, save your data and shut down the computer, or place the computer into Hibernation Mode.
The computer's RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed. Dispose of the battery as required by local ordinances or regulations.
The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, you should charge it at room temperature of between 5°C to 35°C (41°F to 95°F). The battery is nearly completely discharged.
Screen brightness System Sleep Mode System Hibernation Mode Display power off period Hard disk drive power off period How often and for how long you use the hard disk drive and external disk(c) drives, for example, optical disc and floppy diskette drive.
4. Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power. The DC IN indicator should glow green, and the Battery indicator should glow orange to in.
6. Slide and hold the battery release latch to disengage the battery pack and then remove it from the computer. Figure 5-1 Releasing the battery pack (R940) 3 3 1 2 1 2 1.
Windows utilities You can configure various settings associated with both Sleep Mode and Hibernation Mode within the Power Options (to access it, Start -> Control Panel -> System and Security -> Power Options ). Hot keys You can use the FN + F3 hot key to enter Sleep Mode or FN + F4 to enter Hibernation Mode.
Chapter 6 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins.
Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously the.
indicator is glowing, the computer is connected to a live external power source. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
AC power If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN indicator. Please refer to Chapter 5, Power and Power-Up Modes for further information.
Problem Procedure Battery doesn’t charge when the AC adaptor is attached ( Battery indicator does not glow orange). If the battery is completely discharged, it will not begin charging immediately, in these instances you should wait a few minutes before trying again.
Real Time Clock Problem Procedure The following message is displayed on the screen: RTC battery is low. Check system. Then press [F2] key. Your computer will automatically power off after 1 minute and the same message will appear again the next time when it is turned on.
Problem Procedure No display Press the FN + F5 hot keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the computer's display panel. These marks may have come from contact with the keyboard and Touch Pad while the display panel has been closed.
Problem Procedure You cannot access a disc in the drive. Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Open the disc tray and make sure the disc is properly seated. It should lie flat with the label facing up.
Problem Procedure Smart Card error occurs Remove the Smart Card from the computer, make sure to confirm that the card oriented correctly and reinsert it in order to ensure it is firmly connected. If the problem persists, then you should refer to the documentation supplied with your Smart Card for further information.
Problem Procedure The reaction of Touch pad is either too sensitive or not sensitive enough. Adjust the touch Sensitivity. To access it, click Start -> Control Panel -> Hardware and Sound -> Mouse . If you are still unable to resolve the problem, contact TOSHIBA Support.
Fingerprint Sensor Problem Procedure Reading of the fingerprint was not successful. In this instance you should try the fingerprint reading operation again using the correct finger position - please refer to Using the Fingerprint Sensor in Chapter 3, Operating Basics for further information.
Problem Procedure I cannot use the Sleep and Charge function. Sleep and Charge function may be disabled. Select the "Enable Sleep and Charge" check box in the TOSHIBA Sleep utility to enable this function.
Problem Procedure The "USB Wakeup function" does not work. When "System ON CDP Charge Mode" or "USB Sleep and Charge function" is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function.
Problem Procedure If there is a memory malfunction, the Power indicator will repeatedly flash (on for 0.5 seconds, off for 0.5 seconds) in the following patterns; If there is an error in only Slot A: orange twice, then green once. If there is an error in only Slot B: orange once, then green twice.
Problem Procedure Annoying sound is heard In this instance you may be experiencing feedback from either the internal microphone or an external microphone connected to the computer - please refer to Sound System in Chapter 3, Operating Basics for further information.
Problem Procedure No display Try adjusting the contrast and brightness controls on the external monitor. Press the FN + F5 hot key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected.
Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 3, Operating Basics . Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication function is on.
If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. R950 379(w) x 252 (d) x 20.8~25.4 (h) millimeters (with 6 cell battery) R940 341(w) x 239 (d) x 19.
External RGB monitor port pin assignment 6 10 1 5 15 11 Pin Signal Name Description I/O 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6.
Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Wire size: Minimum 0.
6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe and China.
Appendix C Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series.
conditions. Read additional restrictions in your product documentation. Contact TOSHIBA technical service and support, refer to Chapter 6 Troubleshooting for more information. 64-Bit Computing 64-bit processors are designed to take advantage of 32 and 64 bit computing.
achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power. After going through many charge and discharge cycles, the battery will lose its ability to perform at maximum capacity and will need to be replaced.
Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media. User's Manual C-4.
Appendix D Information for Wireless Devices Wireless LAN Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.
If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Card from TOSHIBA. In Europe visit http://www.
Europe Restrictions for Use of 2400.0-2483.5MHz Frequencies in Europe France: Outdoor use limited to 10mW e.i.r.p. within the band 2454-2483.5MHz Military Radiolocation use.Refarming of the 2.4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012.
Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight.
check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS 210 of Industry Canada.
Article 14 The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act.
3. OF : This equipment uses OFDM modulation. 4. 4 : The interference range of this equipment is less than 40m. 5. : This equipment uses a frequency bandwidth from 2,400MHz to 2,483.5MHz. It is possible to avoid the band of mobile object identification systems.
Atheros AR938x Wireless Network Adapter a/b/g/n (a/b/g) Wireless LAN The Name of the radio equipment: AR5BHB116 DSP Research, Inc. Approval Number: D101136003 Intel ® Centrino ® Advanced-N 6235 a/b/g/n (a/b/g) Wireless LAN and Bluetooth The Name of the radio equipment: 6235ANHMW DSP Research, Inc.
As of April 2012 Austria Belgium Bulgaria Canada Cyprus Czech Rep Denmark Estonia Finland France Germany Greece Hong Kong Hungary Iceland India Indonesia Ireland Italy Japan Korea Latvia Liechtenstein.
Index A AC adaptor additional 3-52 connecting 1-3 DC IN 19V jack 2-3, 2-14, 2-25 ASCII characters 3-7 B Battery extending life 5-7 monitoring capacity 5-6 real time clock 2-35, 5-4 save mode 4-9 types.
F Fingerprint Sensor problems 6-12 using 3-8 FN + 1 ( reduce) 3-6 FN + 2 (enlarge) 3-6 FN + 3 (Volume down) 3-6 FN + 4 (Volume up) 3-6 FN + ENTER 3-4 FN + ESC (Mute) 3-5 FN + F1 (Lock) 3-5 FN + F10 (A.
temporarily using overlay (overlay off) 3-7 turning on the overlays 3-7 L LAN cable types 3-32 connecting 3-33 problems 6-17 M Media care Card care 3-38 Memory card care 3-39 Memory additional 3-52 in.
Real Time Clock 6-7 Smart Card 6-9 Sound system 6-15 TOSHIBA support 6-18 Touch Pad 6-10 USB device 6-12 USB mouse 6-11 Wireless LAN 6-18 R Recovery hard disk drive 4-31 Recovery Media 4-30 Restarting.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: Alternating current ANSI: American National Standards Institute A.
KB: kilobyte LAN: local area network LCD: liquid crystal display LED: light emitting diode MB: megabyte MMC: multi media card OCR: optical character recognition (reader) PC: personal computer PCI: per.
Een belangrijk punt na aankoop van elk apparaat Toshiba R940 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Toshiba R940 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Toshiba R940 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Toshiba R940 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Toshiba R940 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Toshiba R940 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Toshiba R940 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Toshiba R940 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
