Gebruiksaanwijzing /service van het product R950 van de fabrikant Toshiba
Ga naar pagina of 195
User's Manual R950 / R940 / R930.
Table of Contents Preface General Precautions Chapter 1 Getting Started Equipment checklist ............................................................................. 1-1 Getting Started .............................................................
Chapter 4 Utilities & Advanced Usage Utilities and Applications ...................................................................... 4-1 Special features ..................................................................................... 4-6 Using the TOSHIBA Sleep Utility .
Copyright © 2012 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Wi-Fi is a registered trademark of the Wi-Fi Alliance. Secure Digital and SD are trademarks of SD Card Association. Memory Stick, Memory Stick Duo, Memory Stick PRO, Memory Stick PRO Duo and Memory Stick Micro are trademarks or registered trademarks of Sony Corporation.
and microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment. FCC conditions This device complies with part 15 of the FCC Rules.
those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards. To avoid general EMC problems, the following guidance should be noted: Onl.
Video Standard Notice THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING VIDEO IN COMPLI.
Following information is only valid for EU-member States: Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product.
These symbols may not stick depending on the country and region where you purchased. Disposing of the computer and the computer's batteries Discard this computer in accordance with applicable laws and regulations. For further information, contact your local government.
ENERGY STAR ® Program Your Computer model may be ENERGY STAR ® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies.
1. Panasonic Precision Devices Co., Ltd. DVD SuperMulti with Double Layer Blu-ray™ Writer drive Panasonic Precision Devices Co., Ltd. 1080 T akano Nagomi-machi Tamana-Gun Kumamoto, Japan SERIAL NO. 2. TOSHIBA SAMSUNG STORAGE TECHNOLOGY DVD SuperMulti with Double Layer TOSHIBA SAMSUNG ST ORAGE TECHNOLOGY KOREA CORPORATION 14F, Bldg.
Preface Congratulations on your purchase of this computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your computer.
Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
Stress injury Carefully read the Instruction Manual for Safety and Comfort . It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture and lighting that can help reduce physical stress.
Chapter 1 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA.
TOSHIBA eco Utility TOSHIBA HW Setup Utility TOSHIBA Web Camera Application TOSHIBA HDD Protection TOSHIBA Service Station TOSHIBA PC Health Monitor TOSHIBA Sleep Utility TOSHIBA Fingerprint Utility User's Manual (this manual) You may not have all the softwares listed above depending on the model you purchased.
Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.
1. Connect the power cord to the AC adaptor. Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model.
Figure 1-4 Opening the display panel (R940) 1 1. Display panel Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. Be careful not to open the display panel too far as this could put stress on the display panel’s hinges and cause damage.
Figure 1-5 Turning on the power (R950) 1 Figure 1-6 Turning on the power (R940) 1 Figure 1-7 Turning on the power (R930) 1 1. Power button Product appearance depends on the model you purchased. Starting up for the first time The Windows 7 Startup Screen will be the first screen displayed when you turn on the power.
Turning off the power The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode. Shut Down Mode When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on.
Before entering Sleep Mode, be sure to save your data. Do not install or remove a memory module while the computer is in Sleep Mode. The computer or the memory module could be damaged. Do not remove the battery pack while the computer is in Sleep Mode (unless the computer is connected to an AC power source).
Close the display panel. Please note that this feature must be enabled within the Power Options (to access it, click Start -> Control Panel -> System and Security -> Power Options ).
You can return to your previous working environment immediately when you turn on the computer. Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature. Allows the use of the panel power off feature.
An error occurs and the computer does not respond to your keyboard commands. If you need to restart the computer, there are three ways this can be achieved: Click Start , point to the arrow icon ( ) and then select Restart from the menu.
Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix C.
Figure 2-1 Front of the computer with display panel closed (R950) 1 3 2 4 5 6 7 1. DC IN indicator 5. Memory media slot indicator 2. Power indicator 6.
Wireless communication indicator The Wireless communication indicator glows orange when the Wireless functions are turned on. Some models are equipped with Wireless functions. Wireless WAN indicator The Wireless WAN indicator glows blue when the Wireless WAN functions are turned on.
Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. External RGB monitor port This port provides 15-pin, analog RGB port.
Smart Card slot This slot allows you to install a Smart Card device. Some models are equipped with a Smart Card slot. Right side (R950) The following figure shows the computer’s right side. Figure 2-3 The right side of the computer (R950) 6 7 5 4 1 2 3 1.
eSATA/USB combo port One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on the right side of the computer. This port with the icon ( ) supports the following functions: USB Sleep and Charge function System ON CDP Charge Mode Optical disc drive The computer may be configured with an optical disc drive.
Back (R950) The following figure shows the computer’s back. Figure 2-4 The back of the computer (R950) 1 1. Battery pack Battery pack The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected.
Battery lock Slide the battery lock to release the battery pack ready for removal. Battery release latch Slide and hold this latch into its "Unlock" position in order to release the battery pack for removal. For more detailed information on removing the battery pack please refer to Chapter 5, Power and Power-Up Modes .
Figure 2-6 The front of the computer with the display panel open (R950) 2 6 11 12 12 9 3 5 1 6 14 16 7 8 18 13 10 15 17 4 1. Display screen 10. Touch Pad ON/OFF button 2. Web Camera* 11. Fingerprint Sensor* 3. Web Camera LED* 12. Touch Pad control buttons 4.
Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger .
TOSHIBA Presentation button The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center. AccuPoint A pointer control device located in the center of the keyboard is used to control the on-screen pointer.
LCD Sensor switch This switch senses when the display panel is either closed or opened and activates the Panel Power Off/On feature as appropriate. For example, when you close the display panel the co.
Power indicator The Power indicator normally glows green when the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash orange - approximately two seconds on, two seconds off.
Figure 2-8 The left side of the computer (R940) 7 8 6 5 4 1 2 3 1. DC IN 19V jack 5. eSATA/USB combo port 2. Cooling vents 6. Universal Serial Bus (USB 3.0) port 3. External RGB monitor port 7. Microphone jack 4. HDMI out port or DisplayPort* 8. Headphone jack * Provided with some models.
eSATA/USB combo port One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on the left side of the computer. This port has eSATA (External Serial ATA) function. This port with the icon ( ) supports the following functions: USB Sleep and Charge function System ON CDP Charge Mode Universal Serial Bus (USB 3.
Smart Card slot This slot allows you to install a Smart Card device. Some models are equipped with a Smart Card slot. Optical disc drive The computer may be configured with an optical disc drive. 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.
Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer. Please note that it is not possible to confirm the operation of all functions of all USB devices that are available.
Figure 2-11 The underside of the computer (R940) 1 5 2 4 6 3 1. Battery lock 4. Battery release latch 2. Docking port* 5. Memory module slot 3. Battery Pack 6. Cooling vents * Provided with some models. Product appearance depends on the model you purchased.
Memory module slot The memory module slot allows the installation, replacement and removal of additional memory module. The size of the memory modules varies depending on the model. The actual amount of useable system memory may be less than the installed memory modules.
Figure 2-12 The front of the computer with the display panel open (R940) 3 4 8 12 17 16 16 14 13 2 1 8 9 10 7 6 4 5 7 11 15 18 1. Display screen 10. Keyboard 2. Microphone* 11. TOSHIBA Presentation button 3. Web Camera LED* 12. TOSHIBA eco button 4. Web Camera* 13.
Microphone A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 3, Operating Basics for more information. Web Camera LED The Web Camera LED glows when the Web Camera is operating.
LCD Sensor switch This switch senses when the display panel is either closed or opened and activates the Panel Power Off/On feature as appropriate. For example, when you close the display panel the co.
AccuPoint A pointer control device located in the center of the keyboard is used to control the on-screen pointer. Refer to the Using the AccuPoint section in Chapter 3, Operating Basics. Some models are equipped with an AccuPoint. Touch Pad ON/OFF button Pressing the Touch Pad ON/OFF button enables or disables the Touch Pad function.
DC IN indicator The DC IN indicator normally glows green when power is being correctly supplied from the AC power adaptor. However, if the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will flash orange.
Left side (R930) The following figure shows the computer’s left side. Figure 2-14 The left side of the computer (R930) 1 2 3 4 6 5 1. DC IN 19V jack 4. eSATA/USB combo port 2. Cooling vents 5. Universal Serial Bus (USB 3.0) port 3. External RGB monitor port 6.
Universal Serial Bus (USB 3.0) port One Universal Serial Bus port, which complies to the USB 3.0 standard, is provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. HDMI out port HDMI out port can connect with Type A connector HDMI cable.
Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. The integrated sound system provides support for the computer's internal speakers and microphone, as well as allowing an external microphone and headphones to be connected via the appropriate jacks.
Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly. USB 3.0 port(s) may work as USB 2.
Figure 2-17 The underside of the computer (R930) 1 2 4 3 5 6 1. Battery lock 4. Battery release latch 2. Docking port* 5. Memory module slot 3. Battery Pack 6. Cooling vents * Provided with some models. Product appearance depends on the model you purchased.
Memory module slot The memory module slot allows the installation, replacement and removal of additional memory module. The size of the memory modules varies depending on the model. The actual amount of useable system memory may be less than the installed memory modules.
Figure 2-18 The front of the computer with the display panel open (R930) 13 11 12 12 10 2 1 17 16 15 3 6 5 7 8 4 14 18 9 1. Display screen 10. Touch Pad ON/OFF button 2. Web Camera* 11. Fingerprint Sensor* 3. Web Camera LED* 12. Touch Pad control buttons 4.
Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger . TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
Microphone A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 3, Operating Basics for more information. Touch Pad ON/OFF button Pressing the Touch Pad ON/OFF button enables or disables the Touch Pad function.
Do not put any magnetic objects close to this switch as they may cause the computer to automatically enter Hibernation Mode and shut down even if the Panel Power Off feature is disabled. Internal Hardware Components This section describes the internal hardware components of your computer.
RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. Video RAM The memory in a computer's graphics adaptor, used to store the image displayed on a bitmap display. The amount of Video RAM available is dependent on the computer's system memory.
Intel ® Display Power Saving Technology (R950 & R940) Intel GPU model may include the Display Power Saving Technology feature that can save the computer's power consumption by optimizing picture contrast on the internal LCD.
Right-click on the desktop and click Graphics Properties... In this control panel: 1. Click Power . 2. Select On battery from the drop-down menu in Power Source .
You can use BIOS Setup to enable/disable the function and change the specified time setting from Sleep Mode to Hibernation Mode. 1. Press and hold the F2 key, and then turn on the computer - the BIOS setup utility will load. 2. Select Advanced . 3. Enable/Disable Intel(R) Rapid Start Technology function.
Chapter 3 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. TOSHIBA Dual Pointing Device Some models are equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.
Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad. Refer to the Using the Touch Pad section for details. Some models are equipped with an AccuPoint. AccuPoint precautions Certain conditions can affect the on-screen pointer when using AccuPoint.
The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages. In use there are six different types of keys, specifically typewriter keys, function keys, soft keys, Hot keys, Windows special keys and the keypad overlay.
Soft keys: FN key combinations The FN (function) is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
3. Click the desired option. To use a Hot Key Card using a hot key: 1. Press and hold the FN key. 2. Press the hot key associated with the desired function. The associated hot key card appears at the top of the screen with its available options below it.
Touch Pad Pressing FN + F9 enables or disables the Touch Pad function. Zoom (Display resolution) Pressing FN + Space changes the display resolution. ODD Pressing FN + TAB ejects the disc tray. Reduce Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows.
Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow Mode To turn on Arrow Mode, press FN + F10 - the Arrow Mode indicator lights and you are able to access cursor and page control functions by using the keys.
2. Using the overlay keys, type the ASCII code of the character you require. 3. Release ALT or ALT + FN - the ASCII character will appear on the display screen. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping.
Enroll two or more fingers. Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers. Check the condition of your finger - any conditions which have changed .
In use, the fingerprint authentication system will use the same username and password as defined within the Windows operating system. If no Windows password has been configured, you must do this before starting the fingerprint registration process. This sensor has the memory space for at least twenty fingerprint patterns.
3. The TOSHIBA Fingerprint Utility main menu is displayed. Select Enroll in the main menu. 4. In the Enroll window, it enables you to delete the fingerprint data for the currently logged in user.
Fingerprint Pre-Boot Authentication and Single Sign- on feature Overview about Fingerprint Pre-Boot Authentication The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up.
Single Sign-On feature. You should check that your fingerprint is enrolled before configuring the settings. 1. Logon as Administrator (means a user has administrator privileges). 2. Click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Fingerprint Utility .
Using optical disc drives The full-size drive provides high-performance execution of disc based programs. You can run either 12 cm (4.72") or 8 cm (3.
3. Lay the disc, label side up, in the disc tray. Figure 3-6 Inserting a disc (R940) 1 1. Laser lens When the disc tray is fully opened, the edge of the computer will slightly cover the disc tray. Therefore, you will need to turn the disc at an angle when you place it in the disc tray.
When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. 2. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc. 3. Push the center of the disc tray to close it.
Blu-ray™ discs BD-R, BD-R DL discs can be written only once. The recorded data cannot be erased or changed. BD-RE, BD-RE DL discs can be recorded more than once. Writing discs The TOSHIBA Disc Creator is provided as writing software with this computer.
two or more copies of important data, in case of any undesired change or loss of the recorded contents. Before writing or rewriting Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of disc media, however, it must be noted that disc quality can affect writing or rewriting success rates.
DVD-RAM: (DVD Super Multi drive only) DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Corporation (for 3x and 5x speed media) Hitachi Maxell, Ltd.
Make sure that the writing/rewriting operation is completed before going into either Sleep Mode or Hibernation Mode (You can remove an optical media on the optical disc drive after writing is completed). If the media is of poor quality, or is dirty or damaged, writing or rewriting errors may occur.
TOSHIBA Disc Creator does not support recording to DVD-RAM discs - to achieve this you should use Windows Explorer or another similar utility. When you back up a DVD disc, be sure that the source driv.
Unfinalized DVDs created on home DVD recorders may not be playable on the computer. Use DVD-Video discs with a region code which is either "the same as the factory default setting" (if applicable) or "ALL". Do not playback video while watching or recording television programs using other applications.
Display Devices & Audio TOSHIBA VIDEO PLAYER will only run when "Colors" is set to "True Color (32 bit)". Click Start -> Control Panel -> Appearance and Personalization -.
Wireless communications The computer’s wireless communication function supports some wireless communication devices. Only some models are equipped with both Wireless LAN and Bluetooth functions. Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields.
electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard - the actual transmission speed will be lower than the theoretical maximum speed.
for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Bluetooth Stack for Windows by TOSHIBA Please note that this software is specifically designed for the following operating systems: Windows 7 Information regarding the use of this software with these operating systems is listed below, with further details being contained with the electronic help files supplied with the software.
The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on). LAN cable types The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation.
2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Figure 3-8 Connecting the LAN cable (R940) 1 2 1.
connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps. Inserting an ExpressCard The Windows hot-install feature allows you to insert ExpressCards while the computer is turned on.
Smart Card A Smart Card is a credit card sized plastic card. An extremely thin integrated circuit (IC chip) is embedded into the card on which information can be recorded. These cards can be used for a wide variety of applications including telephone related and electronic monetary payments.
Before removing the Smart Card, confirm that the Smart Card is not working with any program or system. Be careful not to bend the Smart Card while removing it from the computer. 2. Point to Smart Card and click the left Touch Pad control button. 3. Grasp the Smart Card and remove it.
Points to note about the memory media card SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music.
Do not twist or bend cards. Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid. Do not touch the metal part of a card or expose it to liquids or let it get dirty. After using card, return it to its case. The card is designed so that it can be inserted only one way.
Figure 3-11 Inserting a memory media (R940) 2 1 1. Memory media slot 2. Memory media Make sure memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it. When inserting memory media, do not touch the metal contacts.
Additional memory module You can install additional memory into the computer in order to increase the amount of system memory that is available. This section describes how to install and remove optional memory modules.
2. Remove the AC adaptor and all cables and peripherals connected to the computer. 3. Close the display panel. 4. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section in Chapter 5, Power and Power-Up Modes, if required).
7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. Figure 3-13 Seating the memory module (R940) 3 2 1 1.
8. Seat the memory module cover in place and secure it with the screw(s). Take care to ensure that the memory module cover is firmly closed. Figure 3-14 Seating the memory module cover (R940) 2 1 1.
8. Grasp the module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.
Figure 3-16 Connecting the monitor cable to the External RGB monitor port (R940) 1 2 1. External RGB monitor port 2. Monitor cable There are no fastening screws for an external monitor cable on this computer's External RGB monitor port. However, external monitor cables which have connectors with fastening screws can still be used.
Connecting the HDMI out port 1. Plug one end of the HDMI cable into the HDMI in port of the HDMI device. 2. Plug the other end of the HDMI cable into the HDMI out port on your computer. Figure 3-17 Connecting the HDMI out port (R940) 1 2 1. HDMI out port 2.
Be sure to use the FN + F5 HotKey to select the display device before starting to play video. Do not change the display device while playing video. Do not change the display device under the following conditions. While data is being read or written. While communication is being carried out.
When you change the display output device by hot key like FN + F5 , the playback device may not switch automatically. In this case, in order to set the playback device to the same device as the display output device, please adjust the playback device manually by the following steps: 1.
If you connect an eSATA device after the computer has already been turned on, it will take about ten seconds for it to be recognized by the computer. Do not attempt to disconnect and reconnect the drive before this period has elapsed.
TOSHIBA Docking Station Utility Models with a docking port support system sleep undocking operation. You can enable/disable the system sleep undocking operation. If enabled, the computer goes into Sleep Mode when you undock the computer. You can undock the computer in one of the following ways: Press the Eject button on the port replicator.
Figure 3-19 Security lock (R940) 1 2 1. Security lock slot 2. Security lock Optional TOSHIBA Accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use.
To adjust the volume level of speakers or headphones, move the Speakers slider. To adjust the volume level of an application that you are using, move the slider for the corresponding application. Microphone Level Follow the steps below to change the microphone recording level.
Information Click the Information button to view hardware information, software information, and language setting. Power Management The audio controller in your computer can be turned off when the audio function is not used. To adjust the configuration of audio power management, click the Power Management button .
Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely - in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage.
Heat dispersal To protect against overheating, the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer's internal temperature rises to a certain level.
Chapter 4 Utilities & Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them.
TOSHIBA Button Support This utility controls the following computer button functions. Eco button TOSHIBA Presentation button The starting application from the button can be changed.
Fingerprint Utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints which can then be linked to a username and password in order to remove the need to input these details from the keyboard.
TOSHIBA eco Utility This computer is equipped with "eco mode". This mode slightly lowers performance of some devices to reduce electric power consumption. You can realize measurable power savings by using it continuously. TOSHIBA eco Utility helps you monitor your power savings by showing approximate real time power consumption.
TOSHIBA Sleep Utility This utility is able to either enable or disable the Sleep and Charge function. Sleep and Charge: By connecting to the USB port, devices such as digital audio players are able to charge, even when the computer is in Sleep Mode, Hibernation Mode or shutdown state.
4. Press the Y key to accept the changes. The computer will restart. In order to change the TPM setting when the Hide TPM setting is currently set to Yes, switch the Hide TPM setting from Yes to No . Open Toshiba Security Assist ( Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Security Assist ) and select TPM Settings.
System automatic Sleep/Hibernation Mode *1 This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options. Keypad overlay A ten-key numeric keypad is integrated into the keyboard.
TOSHIBA HDD Protection This feature uses the acceleration sensor built in the computer to detect vibration and shocks, and automatically moves the hard disk drive's read/ write head to a safe position in order to reduce the risk of damage that could be caused by head- to-disk contact.
Sleep and Charge Your computer can supply USB bus power (DC5V) to the USB port even when the power of the computer is turned OFF. "Power OFF" includes Sleep Mode, Hibernation Mode or shutdown state. This function can be used for ports that support the Sleep and Charge function (hereinafter called "compatible ports").
Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag.
remaining battery life falls below the setting, the Sleep and Charge function will be stopped. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from the Windows password.
To end the BIOS Setup, Press F10 , and then press Y to accept the changes. The computer will restart. Change (button) Click this button to change a registered password. Before you can change a password, you must first enter the current password correctly.
Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint System Pre-Boot Authentication. If you would not like to swipe your finger or cannot authenticate the fingerprint for some reasons, push the BACK SPACE key to skip the fingerprint authentication screen.
HW Setup window The HW Setup window contains a number of tabs (General, Display, CPU, Boot Setting, Keyboard, LAN, SATA, USB and Advanced) to allow specific functions of the computer to be configured. In addition there are also three buttons : OK, Cancel and Apply.
Dynamic CPU Frequency Mode This option allows you to configure the power saving modes associated with the processor - the following settings are available: Dynamically Switchable The processor's automatic clock speed switching function is enabled - in use the processor's operation is automatically switched when necessary (default).
If a Supervisor Password has been set, manual boot device selection functions may be restricted. The boot device selection methods described above will not change the boot priority settings that have been configured in HW Setup.
Disabled Disables the Wake-up on Keyboard function. (Default) LAN Wake-up on LAN This feature lets the computer's power be turned on from shutdown when it receives a wake-up packet (Magic packet) from the LAN. Do not install or remove a memory module while Wake-up on LAN is enabled.
Disabled Disables the USB Legacy Emulation. Internal USB 3.0 controller Use this option to enable or disable the internal USB 3.0 controller. If Disabled is selected, the internal USB 3.0 port(s) on the computer will work as USB 2.0 port(s), which will save power.
Disabled Disables the eSATA port in order to save power. SATA Interface setting This feature allows you to set SATA interface setting. Performance Let HDD work with maximum performance. (Default) Battery life Let HDD work with battery life mode. If this setting is selected, this caused performance down.
data protection laws or data protection levels as required by your home country or region. Once enabled, you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel . Doing so will automatically delete all collected information from the HDD.
The TOSHIBA HDD Protection function does not guarantee that the hard disk drive will not be damaged. During audio/video playback, when the computer detects a shock or vibration and the hard disk drive's head is parked, the playback might be temporarily interrupted.
environment such as on a table in the workplace or at home. By setting different detection levels for the computer depending on whether it runs with the AC power (desktop) or with batteries (handheld or mobile usage), the detection level automatically switches according to the power connection mode.
System Recovery There is a hidden partition allocated on the hard disk drive for the System Recovery Options in the event of a problem. You can also create recovery media and restore the system.
Do not write to the media when the virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. Do not use utilities, including those intended to enhance hard disk drive access speed.
the restore process. Please refer to The Keyboard in Chapter 3, Operating Basics, for further details. You can not use System Recovery Options if restoring the pre-installed software without System Recovery Options. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.
otherwise you may find that space for the required software is not available. In addition, if you use a third-party partitioning program to reconfigure the partitions on your hard disk drive, you may find that it becomes impossible to setup your computer.
Computer LCD Yes RGB Yes DisplayPort Yes DisplayPort Model With TOSHIBA Hi-Speed Port Replicator II: Computer LCD Yes Yes Yes - - RGB - - - - - DisplayPort Yes Yes Yes Yes Yes Replicator RGB Yes - - Y.
Chapter 5 Power and Power-Up Modes The computer's power resources include the AC adaptor, battery pack and any internal batteries. This chapter provides details on making the most effective use o.
Power on Power off (no operation) AC adaptor not connected Remaining battery capacity is above low battery trigger point • Operates • LED: Battery off DC IN off Remaining battery capacity is below.
If the battery pack becomes too hot while it is being charged, the charge will stop and the Battery indicator will go out. When the battery pack's temperature falls to a normal range, charging will resume - this process will occur regardless of whether the computer's power is on or off.
use of the computer away from an AC power source although you should not change the battery pack while the AC adaptor is connected. Before you remove the battery pack, save your data and shut down the computer, or place the computer into Hibernation Mode.
The computer's RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed. Dispose of the battery as required by local ordinances or regulations.
The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, you should charge it at room temperature of between 5°C to 35°C (41°F to 95°F). The battery is nearly completely discharged.
Screen brightness System Sleep Mode System Hibernation Mode Display power off period Hard disk drive power off period How often and for how long you use the hard disk drive and external disk(c) drives, for example, optical disc and floppy diskette drive.
If you have extra battery packs, rotate their use. If you will not be using the system for an extended period, for example for more than one month, remove the battery pack from the computer. Store spare battery packs in a cool dry place out of direct sunlight.
Figure 5-1 Releasing the battery pack (R940) 3 3 1 2 1 2 1. Battery lock 3. Battery pack 2. Battery release latch Installing the battery pack To install a battery pack, follow the steps as detailed be.
Hot keys You can use the FN + F3 hot key to enter Sleep Mode or FN + F4 to enter Hibernation Mode. Panel power on/off You can set up your computer so that power is turned off automatically when you close the display panel, and turned on again when you open it.
Chapter 6 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins.
Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously the.
indicator is glowing, the computer is connected to a live external power source. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
AC power If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN indicator. Please refer to Chapter 5, Power and Power-Up Modes for further information.
Problem Procedure Battery doesn’t charge when the AC adaptor is attached ( Battery indicator does not glow orange). If the battery is completely discharged, it will not begin charging immediately, in these instances you should wait a few minutes before trying again.
Real Time Clock Problem Procedure The following message is displayed on the screen: RTC battery is low. Check system. Then press [F2] key. Your computer will automatically power off after 1 minute and the same message will appear again the next time when it is turned on.
Problem Procedure No display Press the FN + F5 hot keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the computer's display panel. These marks may have come from contact with the keyboard and Touch Pad while the display panel has been closed.
Problem Procedure You cannot access a disc in the drive. Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Open the disc tray and make sure the disc is properly seated. It should lie flat with the label facing up.
Problem Procedure Smart Card error occurs Remove the Smart Card from the computer, make sure to confirm that the card oriented correctly and reinsert it in order to ensure it is firmly connected. If the problem persists, then you should refer to the documentation supplied with your Smart Card for further information.
Problem Procedure The reaction of Touch pad is either too sensitive or not sensitive enough. Adjust the touch Sensitivity. To access it, click Start -> Control Panel -> Hardware and Sound -> Mouse . If you are still unable to resolve the problem, contact TOSHIBA Support.
Fingerprint Sensor Problem Procedure Reading of the fingerprint was not successful. In this instance you should try the fingerprint reading operation again using the correct finger position - please refer to Using the Fingerprint Sensor in Chapter 3, Operating Basics for further information.
Problem Procedure I cannot use the Sleep and Charge function. Sleep and Charge function may be disabled. Select the "Enable Sleep and Charge" check box in the TOSHIBA Sleep utility to enable this function.
Problem Procedure The "USB Wakeup function" does not work. When "System ON CDP Charge Mode" or "USB Sleep and Charge function" is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function.
Problem Procedure If there is a memory malfunction, the Power indicator will repeatedly flash (on for 0.5 seconds, off for 0.5 seconds) in the following patterns; If there is an error in only Slot A: orange twice, then green once. If there is an error in only Slot B: orange once, then green twice.
Problem Procedure Annoying sound is heard In this instance you may be experiencing feedback from either the internal microphone or an external microphone connected to the computer - please refer to Sound System in Chapter 3, Operating Basics for further information.
Problem Procedure No display Try adjusting the contrast and brightness controls on the external monitor. Press the FN + F5 hot key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected.
Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 3, Operating Basics . Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication function is on.
If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. R950 379(w) x 252 (d) x 20.8~25.4 (h) millimeters (with 6 cell battery) R940 341(w) x 239 (d) x 19.
External RGB monitor port pin assignment 6 10 1 5 15 11 Pin Signal Name Description I/O 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6.
Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Wire size: Minimum 0.
6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe and China.
Appendix C Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series.
conditions. Read additional restrictions in your product documentation. Contact TOSHIBA technical service and support, refer to Chapter 6 Troubleshooting for more information. 64-Bit Computing 64-bit processors are designed to take advantage of 32 and 64 bit computing.
achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power. After going through many charge and discharge cycles, the battery will lose its ability to perform at maximum capacity and will need to be replaced.
Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media. User's Manual C-4.
Appendix D Information for Wireless Devices Wireless LAN Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.
Your Bluetooth product is not compatible with devices using Bluetooth Version 1.0B specifications Wireless Devices and your health Wireless products, like other radio devices, emit radio frequency electromagnetic energy.
Italy: - For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises. For public use, a general authorization is required.
Restrictions for Use of 5470-5725MHz Frequencies in Europe Italy: - For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises. Luxembourg: Implemented General authorization required for network and service supply Russian Federation: Limited e.
designed to provide reasonable protection against harmful interference in a residential installation. Refer to the FCC information section for the detailed information. Caution: Exposure to Radio Frequency Radiation The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits.
Using this equipment in Japan In Japan, the frequency bandwidth of 2,400MHz to 2,483.5MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).
4. : This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.
Atheros AR9485WB-EG Wireless Network Adapter Wireless LAN and Bluetooth The Name of the radio equipment: AR5B225 DSP Research, Inc. Approval Number: D110317003 Intel ® Centrino ® Wireless-N + WiMAX 6250 Wireless LAN and WiMAX The Name of the radio equipment: 622ANXHMW DSP Research, Inc.
Luxemburg Malta Monaco Netherlands Norway Philippines Poland Portugal Romania Slovak Republic Slovenia Spain Sweden Switzerland UK USA Approved Countries/Regions for Intel ® Centrino ® Wireless-N + .
Index A AC adaptor additional 3-48 connecting 1-3 DC IN 19V jack 2-3, 2-14, 2-25 ASCII characters 3-7 B Battery extending life 5-7 monitoring capacity 5-6 real time clock 2-35, 5-4 save mode 4-7 types.
F Fingerprint Sensor problems 6-12 using 3-8 FN + 1 ( reduce) 3-6 FN + 2 (enlarge) 3-6 FN + 3 (Volume down) 3-6 FN + 4 (Volume up) 3-6 FN + ENTER 3-4 FN + ESC (Mute) 3-5 FN + F1 (Lock) 3-5 FN + F10 (A.
temporarily using overlay (overlay off) 3-7 turning on the overlays 3-7 L LAN cable types 3-29 connecting 3-29 problems 6-17 M Media care Card care 3-35 Memory card care 3-35 Memory additional 3-48 in.
Real Time Clock 6-7 Smart Card 6-9 Sound system 6-15 TOSHIBA support 6-18 Touch Pad 6-10 USB device 6-12 USB mouse 6-11 Wireless LAN 6-18 R Recovery hard disk drive 4-25 Recovery Media 4-24, 4-26 Rest.
User's Manual Glossary-1.
Een belangrijk punt na aankoop van elk apparaat Toshiba R950 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Toshiba R950 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Toshiba R950 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Toshiba R950 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Toshiba R950 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Toshiba R950 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Toshiba R950 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Toshiba R950 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
